Proform 159951 Crossover Elliptical Trainer Users Manual 221997

Proform-159951-Owner-S-Manual proform-159951-owner-s-manual

2015-04-13

: Proform Proform-159951-Crossover-Elliptical-Trainer-Users-Manual-697070 proform-159951-crossover-elliptical-trainer-users-manual-697070 proform pdf

Open the PDF directly: View PDF .
Page Count: 30

Download
Open PDF In Browser	View PDF

Model No. 831.15995.1
Serial No.
Write the serial number in the
space above for future reference.

ELLIPTICAL TRAINER EXERCISER
User’s Manual
Serial Number Decal (Under Seat)

• Assembly
• Adjustments
• Troubleshooting
• Part List and Drawing

CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CONSOLE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
FULL 90-DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.

WARNING DECAL PLACEMENT
The decal shown here has been placed on the
elliptical trainer. If the decal is missing or illegible, please call toll-free 1-888-533-1333, Monday
through Friday, 6 a.m. until 6 p.m. Mountain
Time, and order a free replacement decal. Apply
the decal in the location shown.

IMPORTANT PRECAUTIONS
WARNING:

To reduce the risk of serious injury, read the following important precautions
before using the elliptical trainer.
1. Read all instructions in this manual and all
warnings on the elliptical trainer before using
the elliptical trainer. Use the elliptical trainer
only as described in this manual.

10. The elliptical trainer is designed to support a
maximum user weight of 250 pounds.
11. The elliptical trainer is designed to be used
with the included resistance. Do not use the
elliptical trainer with dumbbells or any other
type of weight to increase the resistance.

2. It is the responsibility of the owner to ensure
that all users of the elliptical trainer are adequately informed of all precautions.

12. Make sure that the cables remain on the pulleys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys. Replace all
cables at least every two years.

3. The elliptical trainer is intended for home use
only. Do not use the elliptical trainer in any
commercial, rental, or institutional setting.
4. Keep the elliptical trainer indoors, away from
moisture and dust. Place the elliptical trainer
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the elliptical trainer to mount, dismount, and use the
elliptical trainer.

13. Hold the handles when mounting, dismounting, or using the elliptical trainer’s elliptical
station.
14. Always keep your back straight when using
the elliptical trainer; do not arch your back.

5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.

15. When you stop using the elliptical station,
allow the pedals to slowly come to a stop.
The elliptical trainer does not have a freewheel; the pedals will continue to move until
the flywheel stops.

6. Keep children under 12 and pets away from
the elliptical trainer at all times.
7. Keep hands and feet away from moving parts.

16. Make sure all electrical connections are complete before connecting the elliptical trainer
to a power source.

8. Wear appropriate clothes when exercising;
do not wear loose clothes that could become
caught on the elliptical trainer. Always wear
athletic shoes for foot protection while exercising.

17. Always unplug the power cord immediately
after use and before cleaning the elliptical
trainer.

9. The pulse sensor is not a medical device.
Various factors, including the user’s movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.

18. Use the high pulley station only when the
seat base is collapsed and secured next to
the upright base.
19. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.

WARNING:

Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

BEFORE YOU BEGIN
after reading this manual, call 1-800-4-MY-HOME®
(1-800-469-4663). To help us assist you, please note
the product model number and serial number before
calling. The model number is 831.15995.1. The serial
number can be found on a decal attached to the elliptical trainer (see the front cover of this manual).

Thank you for selecting the versatile PROFORM®
CROSSOVER ELLIPTICAL TRAINER. The elliptical
trainer offers a selection of weight stations designed to
develop every major muscle group of the body.
Whether your goal is to tone your body, build dramatic
muscle size and strength, or improve your cardiovascular system, the elliptical trainer will help you to achieve
the specific results you want.

Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

For your benefit, read this manual carefully before
using the elliptical trainer. If you have questions

High Pulley Station
ASSEMBLED
DIMENSIONS:
Height: 85 in.
Width: 37 in.
Depth: 83 in.

Top Arm

Console
Handle
Pulse Sensor

Middle Pulley Station
Backrest

Handle

Seat

Pedal
Leg Lever
Low Pulley Station

ASSEMBLY
• As you assemble the elliptical trainer, make sure
all parts are oriented as shown in the drawings.

Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the elliptical trainer can be assembled successfully by anyone. However, it is important to
realize that the versatile elliptical trainer has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.

• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet

Before beginning assembly, carefully read the
following information and instructions:

• One Phillips screwdriver

• Assembly requires two persons.

• Lubricant, such as grease or petroleum jelly,
and soapy water.

• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.

Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.

• Tighten all parts as you assemble them, unless
instructed to do otherwise.

1. Remove the sheath covering the Rope (162).

Attach the Right Arm (12) to the Upright Base (1)
with an M10 x 25mm Button Screw (87), an M10
x 54mm Button Bolt (90), an M10 Split Washer
(114), three M10 Large Black Washers (186), and
an M10 Nylon Locknut (81).

81
186
1 Sheath
162

Attach the Left Arm (13 [not shown]) in the
same manner.

12
186
114
87 90

2. Attach the Seat Stabilizer (9) to the Seat Base (2)
with two M10 x 78mm Carriage Bolts (149) and
two M10 Nylon Locknuts (81).

2
9

149
3. Attach the Upright Stabilizer (10) to the Upright
Base (1) with two M10 x 78mm Button Screws
(101) and two M10 Split Washers (114).

101
114

114

4. Identify the Right Rail (6). Carefully tip the Upright
Base (1) and the Seat Base (2) onto the left side.
Attach the Right Rail to the Upright Base with four
M10 x 25mm Screws (86) and four M10 Large
Zinc Washers (82).

4
2

Turn the Base Knob (44 [not shown]) out and
attach the Left Rail (5 [not shown]) in the
same manner.
1
6

82
82
86
82

82
86

5. Insert the connector of the Upper Wire Harness
(188) into the socket of the Middle Wire Harness
(37). Next, connect the two Wire Harnesses (159)
together in the same manner. Note: The Upper
Wire Harness connector is wider than the Wire
Harness connectors.

5
Pull
188
159

The connectors should slide easily into the
sockets and snap into place. If a connector does
not slide easily and snap into place, turn it over and
then insert it. IF THE CONNECTOR IS NOT
INSERTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON.

Pull the Upper Wire Harness (188) and the Wire
Harness (159) in the indicated location to remove
slack. Slide the Upright (3) into the Upright Base
(1). Be careful not to pinch the Wire
Harnesses. Attach the Upright to the Upright
Base with four M10 x 25mm Patch Screws (135).

159
159

188
37

135
135
6. Hold the Right Handle (16) near the Upright (3).
Connect the Pulse Sensor Wire (54) to the
Sensor Wire Harness (187). Push the excess
wire into the Upright.

6
187
54

103

The connector should slide easily into the socket and snap into place. If the connector does not
slide easily and snap into place, turn it over and
then insert it. IF THE CONNECTOR IS NOT
INSERTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON.

16
102
103
54
184
102
3

Attach the Right Handle (16) to the Upright (3)
with three M8 x 36mm Button Bolts (103) and
three M8 Nylon Locknuts (102). Make sure that
the Locknuts sit inside of the hexagonal holes
in the Right Handle. Be careful not to pinch
the wires with the Bolts.
Note: Make sure that the Long Handgrip (184)
is pushed up against the Pulse Sensor (54).
Repeat this step with the Left Handle (17).

7. Attach the Backrest (22) to the Upright (3) and
the Upright Base (1) with four M6 x 16mm
Screws (130).

130
22
3

130

1
8. Connect the Sensor Wire Harness (187), the Wire
Harness (159), and the Upper Wire Harness
(188) to the Console (71). Push the excess wire
into the Upright (3).

85
188

The connector should slide easily into the socket and snap into place. If a connector does not
slide easily and snap into place, turn it over and
then insert it. IF THE CONNECTOR IS NOT
INSERTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON.

187
85

159

Attach the Console (71) to the Upright (3) with
four M4 x 16mm Screws (85). Make sure that
the wires do not get pinched.
9
9. Attach the two Swivel Arms (58) to the Top Arm
(11) with two M4 x 5mm Screws (131).

131

10. Attach the Top Arm (11) to the Upright (3) with
two M10 x 75mm Patch Screws (99).

Route the Short Cables (163) through the bracket
on the back of the Upright (3).

11
99
163

3
163
Bracket

11. Attach the Leg Lever Bracket (14) to the Seat
Base (2) with two M8 x 40mm Button Screws
(142) and two M8 Split Washers (140).

11
142
140

140
2
14

12. Grease an M10 x 75mm Button Bolt (129). Attach
the Leg Lever (4) to the Leg Lever Bracket (14)
with the Bolt and an M10 Nylon Locknut (81). Do
not overtighten the Locknut; the Leg Lever
must be able to pivot easily.

14
129

13. Attach the Right Pedal (28) to the Right Pedal
Leg (8) with two M8 x 51mm Button Screws (98),
two M8 Split Washers (140), and two M8
Washers (139).

Repeat this step with the Left Pedal (27) and
the Left Pedal Leg (7).

7
28
8

140
139
140

14. Slide a Plastic Spacer (180) onto the right Crank
Shaft (68). Orient the Right Pedal Leg (8) as
shown. Attach the Right Pedal Leg to the Crank
Shaft with an M8 x 19mm Button Screw (94) and
an M8 Large Zinc Washer (74).

14
7

Repeat this step with the Left Pedal Leg (7).

68 180

74
94

15. Attach the Seat (23) to the Seat Base (2) with
four M6 x 16mm Screws (130).

130
2
130

16. Slide the two Foam Pads (64) onto the Leg Lever
(4).

130

16
64

64
4

17. Adjust the Feet (48) under the Upright Stabilizer
(10) to steady the elliptical trainer.

10
18. Make sure that all parts have been properly tightened. The use of the remaining parts will be
explained in ADJUSTMENTS, beginning on the
following page.

ADJUSTMENTS
This section explains how to adjust the elliptical trainer. See the EXERCISE GUIDELINES on page 22 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure that all parts are properly tightened each time the elliptical trainer is used. Replace any worn parts
immediately. The elliptical trainer can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not
use solvents.
ATTACHING THE SHORT CABLES
To use a high pulley station, attach the indicated end
of a Short Cable (163), the end without the ball, to the
Rope (162) with a Cable Clip (157).

Ball
163

When not using the high pulley stations, store the
lower ends of the Short Cables (163) in the indicated
bracket on the back of the Upright (3 [not shown]).

Bracket
157
162

ATTACHING THE LOW PULLEY STATION
162

To use the low pulley station, attach the Long Cable
(164) to the Rope (162) with a Cable Clip (157).
Slide the hook on the Pulley Housing (105) onto the
hook on the Left Rail (6). Attach the Long Cable to
the appropriate attachment (see ATTACHING THE
HAND STRAPS below, or ATTACHING THE LEG
LEVER on page 12).

157

164

6
105
ATTACHING THE HAND STRAPS
To use a Hand Strap (160), connect it to a Short
Cable (163) with a Cable Clip (157). For some exercises, an Extension Strap (175) should be attached
between the Short Cable and the Hand Strap with two
Cable Clips.

157
175
160

The Hand Straps (160) or the Ankle Strap (not
shown) can be attached at any pulley stations in the
same manner.

157

163

ATTACHING THE LEG LEVER
To use the Leg Lever (4), first attach the low pulley
station (see ATTACHING THE LOW PULLEY STATION on page 11). Then, attach the Long Cable (164)
to the Leg Lever (4) with a Cable Clip (157). Always
attach both Long Cables to the Leg Lever before
using the Leg Lever. Note: The elliptical trainer
must be in the collapsed position while the leg
lever is used.
4

164
157

EXTENDING THE SEAT BASE
7
To use the Pedal Legs (7, 8), turn the Base Knob (44)
to loosen it. Extend the elliptical trainer by pulling the
Seat Base (2) away from the Upright Base (1) until it
stops. Retighten the Base Knob into the Seat Base.
Collapse the elliptical trainer in the same manner.
Always make sure the Base Knob is fully tightened before using the elliptical trainer.

If it is difficult to extend the elliptical trainer, see
ADJUSTING THE FEET on page 13.
8
2
TIGHTENING THE ROPE
The type of rope used on the resistance system can
stretch slightly when it is first used. If there is slack in
the rope before resistance is felt, the rope should be
tightened.

58
162

To tighten the Rope (162), first set the elliptical trainer
resistance level to 100 pounds. Locate the end of the
Rope with the Clamps (193, 194) and pull it out until
the Rope is tight. Then, measure the distance between
the Rope Cover (191) and the Swivel Arm (58).

Measure
Distance

191
144

Set the elliptical trainer resistance to the lowest level.
Have a second person pull the Rope (162) out and
hold it while the Rope is adjusted. Push the Rope
Cover (191) down the Rope and loosen the two M5 x
21mm Flat Head Screws (144). Pull the Rope through
the Link (192) and the Rope Clamps (193, 194) to
shorten the Rope by the measured amount. Then,
retighten the two Screws and cover the Rope Clamps
with the Rope Cover.

191
162

194

192

WARNING: Always make sure the

193

two M5 x 21mm Flat Head Screws (144) are fully
tightened before the elliptical trainer is used.

MOVING THE ELLIPTICAL TRAINER
To move the elliptical trainer, first unplug the
Transformer (not shown) from the 120-volt outlet and
secure the elliptical trainer in the collapsed position
(see EXTENDING THE SEAT BASE on page 12).
Then, using the handle on the Upright Stabilizer (10),
tilt the elliptical trainer onto the Stabilizer Wheels (47).
Finally, move the elliptical trainer to the new location.

WARNING:

The elliptical trainer is
heavy; lift with your knees to prevent injury to
your back. Moving the elliptical trainer may
require two persons.

CAUTION:

When lifting the elliptical
trainer, do not allow the upper swivel arms to
touch the ceiling.

ADJUSTING THE FEET
10
If extending the elliptical trainer is difficult, adjust the
Feet (48) so that the Seat Base (2) is parallel to the
Upright Base (1). Adjust the Feet (A) all of the way
into the Upright Base. Adjust the Feet (B) so that the
Upright Stabilizer (10) is raised slightly.
48–B
1

48–A

EXERCISING ON THE ELLIPTICAL STATION
To mount the elliptical station, firmly hold the Handles
(16, 17) and carefully step onto the Pedal (27 or 28)
that is in the lowest position. Next, step onto the other
Pedal. Push the Pedals until they begin to move with
a continuous motion. Note: The Belt Pulley Covers
(29) can turn in either direction. It is recommended that you turn the Belt Pulley Covers in the
direction shown by the arrow below; however, for
variety, you may turn the Belt Pulley Covers in the
opposite direction.

To dismount the elliptical station, allow the Pedals (27
or 28) to come to a complete stop. Note: The elliptical trainer does not have a free wheel; the Pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
Pedal first. Then, step off the lowest Pedal.

28
29

CONSOLE OPERATION
FEATURES OF THE CONSOLE

Ten crossover training programs are also offered. Each
crossover training program combines elliptical exercise
with strength training exercises to give you a combined
cardiovascular and strength workout.
The console also features iFIT.com interactive technology. Having iFIT.com technology is like having a personal trainer in your home. Using a stereo audio cable
(available at electronics stores), you can connect the
elliptical trainer to your home stereo, portable stereo,
computer, or VCR and play special iFIT.com CD and
video programs (iFIT.com CDs and videocassettes are
available separately). iFIT.com CD and video programs
automatically control the resistance of the elliptical
trainer and prompt you to vary your pace as a personal trainer coaches you through every step of your elliptical workout. High-energy music provides added motivation. To purchase iFIT.com CDs and videocassettes, call toll-free 1-888-533-1333.
With the elliptical trainer connected to your computer,
you can also go to our Web site at www.iFIT.com and
access programs directly from the internet. Explore
www.iFIT.com for more information.
PLUGGING IN THE ELLIPTICAL TRAINER

The heart of the elliptical trainer is the digital resistance
training console, offering an impressive array of features designed to make your workouts more effective.
When the manual mode of the console is selected, you
can change the resistance of the elliptical trainer with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even monitor your heart rate using the integrated pulse sensor.
The console also features six elliptical training programs and six strength training programs. Each program will guide you through an effective cardiovascular,
weight loss, strength, or toning workout.

Plug the indicated
end of the transJack
former into the jack
in the left mech
cover. Plug the
other end of the
transformer into a
Transformer
120-volt outlet. All
indicators and displays on the console will flash once; the console will then be ready for
use. The motor may be heard while the elliptical trainer
calibrates itself. Important: Always plug in the transformer when using the elliptical trainer. Note: When
the power is on, the words MANUAL MODE will appear
in the CROSSOVER TRAINING display. If the buttons
are not pressed, the cables are not pulled, and the
pedals are not moved for ten minutes, the console will
go to sleep. Press any button to resume exercising.
To use the elliptical training features, see ELLIPTICAL TRAINING on pages 15 and 16. To use the
strength training features, see STRENGTH TRAINING on pages 16 and 17. To use a crossover training
program, see CROSSOVER TRAINING on page 18.

To reset the display modes to their default settings,
press the RESET button. The SCAN display mode
will be selected.

ELLIPTICAL TRAINING
MANUAL OPERATION

6. Measure Your Heart Rate if Desired.
1. Plug In the Transformer.
If there are thin sheets
of plastic on the metal
contacts on the pulse
sensors, peel off the
plastic. Place your hands
on the pulse sensors, with
your palms on the metal
contacts. Avoid moving
Contacts
your hands. When your
pulse is detected, two or
three dashes (– – –) will
appear in the ELLIPTICAL TRAINING display and
then your heart rate will be shown. For the most
accurate heart rate reading, continue to hold the
pulse sensors for about 30 seconds. Note: If you
continue to hold the pulse sensors, the display will
shown your heart rate for 30 seconds. The display
will then show your heart rate along with the other
display modes.

See PLUGGING IN THE ELLIPTICAL TRAINER on
page 14. Important: Always plug in the transformer when using the elliptical trainer.
2. Extend the Seat Base.
See EXTENDING THE SEAT BASE on page 12.
3. Select the Manual Mode.
When the transformer is plugged in, the manual
mode will be selected. If you have already selected
a program, press the ELLIPTICAL TRAINING
PROGRAMS button repeatedly until the words
MANUAL MODE reappear in the CROSSOVER
TRAINING display.
4. Begin Pedaling and Select a Resistance Level.

If your heart rate is not shown, make sure that your
hands are positioned as described. Avoid moving
your hands excessively or squeezing the metal contacts too tightly. For optimal performance, periodically clean the metal contacts using a soft cloth;
never use alcohol, abrasives, or chemicals.

When you begin pedaling,
the TOTAL TIME display
will be started. This display can be started and
stopped with the
START/STOP button.
The resistance of the pedals can be set at any of
ten levels. To select a
resistance level, press the
RESISTANCE + and –
buttons. The selected
resistance level will be displayed in the ELLIPTICAL
TRAINING display.
5. Select a Display Mode.
When the SCAN indicaMode Indicator
tor appears, the ELLIPTICAL TRAINING display
will show six display
modes in succession:
RPM, TIME, PULSE,
RESISTANCE, CALORIES, and TOTAL REVOLUTIONS.

7. Unplug the Transformer.
When you finish your workout, unplug the transformer from the 120-volt outlet.
PROGRAM OPERATION
The console offers a level 1 (beginning) elliptical training program, two level 2 (intermediate) programs, and
three level 3 (advanced) programs. To use an elliptical training program, first follow steps 1 and 2 at
the left. Then, follow the steps below.
3. Select an elliptical training program.
To select one of the
six elliptical training
programs, press the
ELLIPTICAL
TRAINING
PROGRAMS button
repeatedly. When an elliptical training program is
selected, the name of the selected program will
appear in the CROSSOVER TRAINING display.
The ELLIPTICAL TRAINING display will show how
long the program will last.

To select a single display mode, press the MODE
button repeatedly until the desired mode indicator
appears; make sure that the SCAN indicator does
not appear. To reselect the SCAN display mode,
press the MODE button until the SCAN indicator
appears.

4. Begin Pedaling or Press the START/STOP
Button to Start the Program.

STRENGTH TRAINING

When you begin pedaling, the TOTAL TIME display will be started. This display and the program
can be started and stopped with the START/STOP
button.

MANUAL OPERATION
1. Plug In the Transformer.
See PLUGGING IN THE ELLIPTICAL TRAINER
on page 14. Important: Always plug in the transformer when using the elliptical trainer.

Each program consists of several time periods of
different lengths. One resistance setting and one
target pace are programmed for each segment.

2. Collapse the Seat Base.
At the end of each period of the program, a tone
will sound. If a different resistance setting is programmed for the next period, the resistance setting
will flash in the ELLIPTICAL TRAINING display, a
series of tones will sound, and the resistance of
the pedals will change. Note: You can override the
resistance setting, if desired, by pressing the
RESISTANCE + and – buttons. However, when the
next period begins, the resistance will change if a
different resistance setting is programmed for the
next period.

See EXTENDING THE SEAT BASE on page 12.
3. Select the Manual Mode.
When the transformer is plugged in, the manual
mode will be selected. If you have already selected
a program, press the STRENGTH TRAINING
PROGRAMS button repeatedly until the words
MANUAL MODE reappear in the CROSSOVER
TRAINING display.

5. Use the RPM Pace Guide.

4. Select a Resistance Setting for the First
Exercise that You Plan to Do.

During elliptical training
programs, the RPM pace
guide above the ELLIPTICAL TRAINING display
will indicate whether you
are pedaling at the target
pace. When one of the lights on the left side of the
pace guide lights, increase your pedaling pace.
When one of the lights on the right side of the
pace guide lights, decrease your pace. When the
center light is lit, maintain your current pace.
Important: The target pace is intended only to
provide a goal. Make sure to pedal at a pace
that is comfortable for you.

The current resistance
setting will appear in the
SYSTEM RESISTANCE
display. To change the
resistance setting, first
make sure that no
cables are being pulled. Next, press the
SYSTEM RESISTANCE + and – buttons. Each
time a button is pressed, the resistance setting will
change by 1 pound. To change the resistance setting quickly, hold down one of the buttons.
Note: While the resistance setting is changing, the
motor will be heard. To prevent damage to the
motor, do not pull any of the cables while the
resistance setting is changing. If a cable is
pulled, the words RELEASE HANDLES AND
READJUST RESISTANCE AS DESIRED may
appear in the CROSSOVER TRAINING display.

6. Select a Display Mode and Measure Your Heart
Rate if Desired.
See steps 5 and 6 on page 15.
7. Unplug the Transformer.

5. Enter the Numbers of Sets and Repetitions that
You Plan to Do.

When you complete your workout, unplug the
transformer from the 120-volt outlet.

To enter the number of
sets that you plan to do,
press the SETS + and –
buttons. To enter the
number of repetitions that
you plan to do, press the
REPS + and – buttons.

IFIT.COM PROGRAM OPERATION
To use an iFIT.com program with the elliptical trainer,
see IFIT.COM ELLIPTICAL TRAINING on page 19.

4. Select a Strength Training Program.

Note: If you do not enter the numbers of sets and
repetitions that you plan to do, the console will
count the total number of repetitions that you do
during your workout.

To select one of the
six strength training
programs, press the
STRENGTH
TRAINING
PROGRAMS button
repeatedly. When a strength training program is
selected, the name of the selected program will
appear in the CROSSOVER TRAINING display for
a few seconds. The name of the first exercise in the
program will then be displayed.

6. Perform the Exercise.
When you begin exercising, the TOTAL TIME display will be started. This
display can be started
and stopped with the
START/STOP button.

5. Perform the Exercise.

If you have entered numbers of sets and repetitions, the console will count down the repetitions
and sets you have completed.

The resistance setting and the numbers of sets and
repetitions for the first exercise will appear in the
SYSTEM RESISTANCE, SETS, and REPS displays.
The resistance setting and the numbers of sets and
repetitions may be too high or too low for you,
depending on such factors as your body size and
your physical condition. If desired, adjust the resistance setting and the numbers of sets and repetitions
by pressing the buttons below the three displays.

Note: The elliptical trainer uses progressive resistance. As the ends of the cable begin to be pulled,
the resistance will increase gradually. As the cable
ends are pulled farther, the resistance will increase
rapidly.
When you complete the exercise, repeat steps 4
to 6 for each exercise that you wish to do.

When you begin exercising, the TOTAL TIME display will be started. This display and the program
can be started and stopped with the START/STOP
button.

7. Unplug The Transformer.
When you complete your workout, unplug the transformer from the 120-volt outlet.

As you perform the exercise, the console will count
down the sets and repetitions you have completed.
A tone will sound each time a repetition is performed, and two tones will sound when all of the
sets for the exercise are completed.

PROGRAM OPERATION
The console offers two ab and back strength training
programs, two upper body programs, and two lower
body programs. To use a strength training program,
first follow steps 1 and 2 on page 16. Then, follow
the steps below.

After you have completed the exercise, press the
NEXT button; the name of the next exercise in the
program will appear in the CROSSOVER TRAINING
display. Repeat this step for the next exercise.

3. Designate Yourself as User 1, 2, or 3.
During strength training and crossover training programs, a resistance setting is programmed for
each strength exercise. If you change the resistance setting, the console will remember your setting and use it the next time you use the program.
The console can remember settings for three different users.

When you complete the program, the words WORKOUT COMPLETE will appear in the main display.
6. Unplug the Transformer.

To designate yourself as
user 1, 2, or 3, press the
SELECT USER button.
Make sure to select the
same user number each
time you use a strength
training or crossover training program.

When you complete your workout, unplug the transformer from the 120-volt outlet.

When the time in the
CROSSOVER TRAINING display reaches
00:00, the name of the
first strength exercise
and a time period of 2
minutes will appear in the display. Collapse the seat
base, and perform as many repetitions of the exercise as you can while the time is counted down in
the display. Note: If desired, change the resistance
setting by pressing the SYSTEM RESISTANCE +
and – buttons.

CROSSOVER TRAINING
The console offers ten crossover training programs that
combine elliptical exercise with strength training exercises. To use a crossover training program, follow
the steps below.
1. Plug In the Transformer.
See PLUGGING IN THE ELLIPTICAL TRAINER on
page 14. Important: Always plug in the transformer when using the elliptical trainer.
2

When the time in the CROSSOVER TRAINING display reaches 00:00, the name of the next strength
exercise and a time period of 1 minute will appear
in the display. Perform as many repetitions of the
next exercise as you can while the time is counted
down in the display.

Designate Yourself as User 1, 2, or 3.
See step 3 on page 17.

3. Select a Crossover Training Program.
To select one of the
ten crossover training
programs, press the
CROSSOVER
TRAINING
PROGRAMS button
repeatedly. When a crossover training program is
selected, the number of the selected program will
appear in the CROSSOVER TRAINING display.
4. Press the START/STOP Button to Start the
Program.

After you have performed strength exercises, the
word ELLIPTICAL and a time period will again
appear in the CROSSOVER TRAINING display.
Extend the seat base and begin pedaling. Continue
pedaling while the time is counted down in the display.
The program will continue in this way. When you
complete the program, the words WORKOUT COMPLETE will appear in the main display.
5. Unplug the Transformer.

When the program is
started, the TOTAL TIME
display will be started.
This display and the program can be started and
stopped with the
START/STOP button.

When you complete your workout, unplug the transformer from the 120-volt outlet.

When the program
begins, the word
ELLIPTICAL and a
time period of 3 or 4
minutes will appear in
the CROSSOVER
TRAINING display. Extend the seat base and begin
pedaling. Continue to pedal while the time is counted down in the display.

• Adjust the volume of your CD player or VCR. If
the volume is too high or too low, the console
may not detect the program signals.

IFIT.COM ELLIPTICAL TRAINING
IFIT.COM CD AND VIDEO PROGRAMS
To use iFIT.com CDs or videocassettes, the elliptical
trainer must be connected to your portable CD player,
portable stereo, home stereo, computer with CD player, or VCR. See HOW TO CONNECT YOUR CD
PLAYER, VCR, OR COMPUTER on pages 20 and 21.
To purchase iFIT.com CDs and videocassettes, call
toll-free 1-833-533-1333. Follow the steps below to
use an iFIT.com CD or video program.
1. Plug In the Transformer.
See PLUGGING IN THE ELLIPTICAL TRAINER on
page 14. Important: Always plug in the transformer when using the elliptical trainer.
2. Extend the Seat Base.
See EXTENDING THE SEAT BASE on page 12.
3. Select the iFIT.com Mode.
To select the iFIT.com mode, press the iFIT.com
button. The indicator above the button will light,
and the words IFIT MODE will appear in the
CROSSOVER TRAINING display.

• Make sure that the audio cable is properly connected and that it is fully plugged in.
6. Unplug the Transformer.
When you complete your workout, unplug the transformer from the 120-volt outlet.
IFIT.COM INTERNET PROGRAMS
Our Web site at www.iFIT.com allows you to play
iFIT.com programs directly from the internet. To use
programs from our Web site, the elliptical trainer must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 21. In addition, you must have an internet connection and an
internet service provider. A list of specific system
requirements is found on our Web site. To use an
iFIT.com program from our Web site, first follow
steps 1 to 3 at the left. Then, follow the steps
below.
4. Go to Your Computer and Start an Internet
Connection.
5. Start Your Web Browser, if Necessary, and Go
to Our Web Site at www.iFIT.com.

4. Insert the iFIT.com CD or Videocassette.
If you are using an iFIT.com CD, insert the CD into
your CD player. If you are using an iFIT.com videocassette, insert the videocassette into your VCR.
5. Press the Play Button on Your CD Player or
VCR.

6. Follow the Desired Links on Our Web Site to
Select a Program.
Read and follow the on-line instructions for using a
program.
7. Follow the On-line Instructions to Start the
Program.

A moment after the play button is pressed, your
personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions.

When you start the program, an on-screen countdown will begin.
8. Begin Exercising on the Elliptical Trainer.

The program will function in almost the same way
as an elliptical training program. However, an electronic “chirping” sound will alert you when the resistance of the pedals and/or the target pace is about to
change.
Note: If the resistance of the pedals and/or the
RPM pace guide does not change when a
“chirp” is heard:

When the on-screen countdown ends, the program
will begin. The program will function in almost the
same way as an elliptical training program.
However, an electronic “chirping” sound will alert you
when the resistance of the pedals and/or the target
pace is about to change.
9. Unplug the Transformer.

• Make sure that the iFIT.com indicator is lit.

When you complete your workout, unplug the transformer from the 120-volt outlet.

HOW TO CONNECT YOUR PORTABLE STEREO

HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER

To use iFIT.com programs, a
stereo audio cable must be
plugged into the iFIT jack on
the back of the console.

Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
1/8" LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.

iFIT
Jack

A. Plug one end
A/B
of a 1/8" to
RCA stereo
audio cable
(available at
electronics
stores) into the
Audio
console iFIT
Cable
jack. Plug the
other end of the
cable into the
AUDIO OUT
jack on your stereo.

To use iFIT.com CDs, the
elliptical trainer must be connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
20 and 21 for connecting instructions. To use iFIT.com
videocassettes, the elliptical trainer must be connected to your VCR. See page 21 for connecting instructions. To use iFIT.com programs directly from our
Web site, the elliptical trainer must be connected to
your home computer. See page 21 for connecting
instructions.

AUDIO OUT

LINE OUT

RIGHT
LEFT

B. See the drawing above. Plug one end of a 1/8" to
1/8" stereo audio cable (available at electronics
stores) into the console iFIT jack. Plug the other
end of the cable into the LINE OUT jack on your
stereo.

HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT
and PHONES jacks, see instruction A below. If
your CD player has only one jack, see instruction B.

C. Plug one end
C
of a 1/8" to 1/8"
stereo audio
cable (available
PHONES
at electronics
stores) into the
console iFIT
1/8"
Audio
Y-adapter
Cable
jack. Plug the
other end of
the cable into a
1/8" Y-adapter
Headphones
(available at
electronics
stores). Plug the Y-adapter into the PHONES jack
on your stereo. Plug your headphones into the
other side of the Y-adapter.

A. Plug one end
A
of a 1/8" to
1/8" stereo
LINE OUT
PHONES
audio cable
(available at
electronics
HeadAudio
stores) into
phones
Cable
the console
iFIT jack. Plug
the other end
of the cable
into the LINE OUT jack on your CD player. Plug
your headphones into the PHONES jack.
PHONES LINE OUT

B. Plug one end
B
of a 1/8" to
1/8" stereo
PHONES
audio cable
(available at
1/8"
electronics
Audio Y-adapter
stores) into
Cable
the console
iFIT jack. Plug
the other end
Headphones
of the cable
into a 1/8" Yadapter (available at electronics stores). Plug the Yadapter into the PHONES jack on your CD player.
Plug your headphones into the other side of the Yadapter.
PHONES

HOW TO CONNECT YOUR HOME STEREO

B. Plug one end
B
of a 1/8" to 1/8"
stereo audio
cable (available
PHONES
at electronics
stores) into the
jack beneath
1/8”
Audio
the console.
Y-adapter
Cable
Plug the other
end of the
cable into a
Headphones/
1/8" Y-adapter
Speakers
(available at
electronics
stores). Plug the Y-adapter into the PHONES jack
on your computer. Plug your headphones or speakers into the other side of the Y-adapter.

Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of
a 1/8" to RCA
stereo audio
cable (available
at electronics
stores) into the
console iFIT
jack. Plug the
other end of the
cable into the
LINE OUT jack
on your stereo.

CD
VCR
Amp

LINE OUT

Audio
Cable

HOW TO CONNECT YOUR VCR
B. Plug one end of
B
CD
a 1/8" to RCA
stereo audio
VCR
cable (available
Amp
at electronics
stores) into the
console
iFIT.com jack.
RCA
Plug the other
Audio Y-adapter
end of the cable
Cable
into an RCA Yadapter (availWire removed
able at electronfrom LINE
ics stores).
OUT jack
Next, remove
the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.

Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 20.

LINE OUT

A. Plug one end
A
of a 1/8" to
RCA stereo
AUDIO OUT
audio cable
RIGHT
(available at
LEFT
electronics
Audio
stores) into the
Cable
console
iFIT.com jack.
Plug the other
end of the
cable into the AUDIO OUT jack on your VCR.

RF OUT

CH
3 4

OUT

B. Plug one end
B
of a 1/8" to
RCA stereo
audio cable
(available at
electronics
RCA
stores) into the
Y-adapter
Audio
console
Cable
iFIT.com jack.
Plug the other
end of the
Wire removed from
cable into an
AUDIO OUT jack
RCA Y-adapter
(available at
electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.

HOW TO CONNECT YOUR COMPUTER

ANT. IN

VIDEO AUDIO
IN

RF OUT

CH
3 4

Note: If your computer has a 1/8" LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of
A
a 1/8" to 1/8"
stereo audio
cable (available
at electronics
stores) into the
Audio
jack beneath
Cable
the console.
Plug the other
end of the
cable into the
LINE OUT jack on your computer.

ANT. IN

VIDEO AUDIO
IN

OUT

LINE OUT

EXERCISE GUIDELINES
EXERCISE INTENSITY

CARDIOVASCULAR EXERCISE GUIDELINES

Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.

WORKOUT GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
Each workout should include the following three parts:
Warming Up—Begin each workout with 5 to 10 minutes of stretching and light exercise. A proper warmup increases your body temperature, heart rate, and
circulation in preparation for exercise.
Training Zone Exercise—Each workout should consist of 20 to 30 minutes of exercising with your heart
rate in your training zone. Note: During the first few
weeks of your exercise program, do not keep your
heart rate in your training zone for longer than 20 minutes.

To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers
above your age. The three numbers are your “training
zone.” The lowest number is the recommended heart
rate for fat burning; the middle number is the recommended heart rate for maximum fat burning; the highest number is the recommended heart rate for aerobic
exercise.

Cooling Down—End each workout with 5 to 10 minutes of stretching. This will increase the flexibility of
your muscles and will help to prevent post-exercise
problems.
Exercise Frequency—To maintain or improve your
condition, plan three workouts each week, with at
least one day of rest between workouts. After a few
months of regular exercise, you may complete up to
five workouts each week, if desired. Remember, the
key to success is make exercise a regular and enjoyable part of your everyday life.

Fat Burning—To burn fat effectively, you must exercise at a relatively low intensity level for a sustained
period of time. During the first few minutes of exercise, your body uses easily accessible carbohydrate
calories for energy. Only after the first few minutes of
exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the
intensity of your exercise until your heart rate is near
the lowest number in your training zone as you exercise. For maximum fat burning, adjust the intensity of
your exercise until your heart rate is near the middle
number in your training zone as you exercise.

WARNING:

The pulse sensor is
not a medical device. Various factors may
affect the accuracy of heart rate readings. The
pulse sensor is intended only as an exercise
aid in determining heart rate trends in general.

Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, your exercise must be “aerobic.” Aerobic exercise is activity that requires large
amounts of oxygen for prolonged periods of time. This
increases the demand on the heart to pump blood to
the muscles, and on the lungs to oxygenate the
blood. For aerobic exercise, adjust the intensity of
your exercise until your heart rate is near the highest
number in your training zone.

Staying Motivated—For motivation, keep a record of
each workout. List the date, the exercises performed,
the resistance used, and the numbers of sets and
repetitions completed. Record your weight and key
body measurements at the end of every month.
Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.

STRENGTH TRAINING GUIDELINES
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
and the number of repetitions or sets to complete, is
an individual matter. It is important to avoid overdoing
it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience
pain or dizziness at any time while exercising, stop
immediately and begin cooling down. Find out what is
wrong before continuing. Remember that adequate
rest and a proper diet are important factors in any
exercise program.

THE BASIC TYPES OF STRENGTH WORKOUTS
Muscle Building—To increase the size and strength
of your muscles, push them close to their maximum
capacity. Your muscles will continually adapt and grow
as you progressively increase the intensity of your
exercise. You can adjust the intensity of an individual
exercise in two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise. A “set” is a series of repetitions.)

Warming Up—Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up.
Warming up prepares your body for more strenuous
exercise by increasing circulation, raising your body
temperature, and delivering more oxygen to your
muscles.

The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
right for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.

Working Out—Each workout should include 6 to 10
different exercises. Select exercises for every major
muscle group, emphasizing areas that you want to
develop most. To give balance and variety to your
workouts, vary the exercises from session to session.

Toning—You can tone your muscles by pushing them
to a moderate percentage of their capacity. Select a
moderate amount of resistance and increase the number of repetitions in each set. Complete as many sets
of 15 to 20 repetitions as possible without discomfort.
Rest for 1 minute after each set. Work your muscles
by completing more sets rather than by using high
amounts of resistance.

Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Exercise Form—Maintaining proper form is an
essential part of an effective exercise program. This
requires moving through the full range of motion for
each exercise, and moving only the appropriate parts
of the body. Exercising in an uncontrolled manner will
leave you feeling exhausted. On the exercise guide
accompanying this manual you will find photographs
showing the correct form for several exercises, and a
list of the muscles affected.

Weight Loss—To lose weight, use a low amount of
resistance and increase the number of repetitions in
each set. Exercise for 20 to 30 minutes, resting for a
maximum of 30 seconds between sets.
Cross Training—Cross training is an efficient way to
get a complete and well-balanced fitness program. An
example of a balanced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an exercise cycle
or an elliptical exerciser, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise for at least one full day each week to give your
body time to regenerate.

The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
Cooling Down—End each workout with 5 to 10 minutes of stretching. Include stretches for both your arms
and legs. Ease into each stretch gradually and go only
as far as you can without strain. Move slowly as you
stretch and do not bounce. Stretching at the end of
each workout is an effective way to increase flexibility.

The combination of strength training and aerobic exercise will reshape and strengthen your body, plus
develop your heart and lungs.

PART IDENTIFICATION CHART
See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may
have been pre-attached for shipping purposes. If you cannot find a part in the parts bag, check to see if
it has been pre-attached. If a part is missing, call toll-free 1-888-533-1333.

M8 Nylon Locknut (102)

M10 x 25mm Patch Screw (135)

M8 Large Zinc Washer (74)
M10 x 25mm Button Screw (87)
M10 Nylon Locknut (81)
M8 x 36mm Button Bolt (103)

M10 Large Zinc/Black
Washer (82, 186)

M10 Split Washer (114)

M8 x 40mm Button Screw (142)

M8 x 51mm Button Screw (98)
M8 Split Washer (140)
M8 Washer (139)
M4 x 5mm Screw (131)

M4 x 16mm Screw (85)

M6 x 16mm Screw (130)

M8 x 19mm Button Screw (94)

M10 x 25mm Screw (86)

M10 x 54mm Button Bolt (90)

M10 x 75mm Patch Screw (99)

M10 x 75mm Button Bolt (129)

M10 x 78mm Button Screw (101)

M10 x 78mm Carriage Bolt (149)

PART LIST—Model No. 831.159951
Key No.

Qty.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
2
2
1
1
2
2
4
1
8
5
4
2
2

Description
Upright Base
Seat Base
Upright
Leg Lever
Left Rail
Right Rail
Left Pedal Leg
Right Pedal Leg
Seat Stabilizer
Upright Stabilizer
Top Arm
Right Arm
Left Arm
Leg Lever Bracket
Mech Frame
Right Handle
Left Handle
Large Belt Pulley
Fly Wheel
Left Mech Cover
Right Mech Cover
Backrest
Seat
“C”-magnet
Right Side Shield
Left Side Shield
Left Pedal
Right Pedal
Belt Pulley Cover
Disk Cap
Crank
Idler
Return Spring
Guide Rod
Resistance Cable
Bushing Bracket
Middle Wire Harness
Leg Lever Bumper
Leg Lever Bushing
19mm Round Inner Cap
38mm x 50mm Inner Cap
Top Arm Cap
Pedal Wheel
Base Knob
Left Rail Cap
Seat Stabilizer Cap
Stabilizer Wheel
Foot
Left Base Bushing
Swivel Bearing
1 3/4" Pulley
“V”-pulley
Resistance Band
Pulse Sensor/Wire

R0305A

Key No. Qty.
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108

7
2
2
4
1
3
2
1
1
2
10
2
2
2
1
4
1
2
1
2
2
1
1
2
1
2
13
8
14
2
32
8
2
1
2
6
1
6
4
2
6
2
1
4
2
6
2
7
6
2
2
3
1
3

Description
3 1/2" Pulley
Band Wheel
Flange Spacer
Swivel Arm
Rep Counter
Limit Switch
Mech Arm Plate
Bungee Cord
Resistance Motor
Foam Pad
Small Base Wheel
Disk Hub
Double Locknut
Crank Shaft
System Wire Harness
M6 x 12mm Flat Head Screw
Console
M8 x 51mm Bolt Set
Right Rail Cap
M8 Large Zinc Washer
Arm Cap
Mech Arm
Motor Assm.
M10 x 30mm Button Screw
Lower Pulley Plate
2 3/4" Pulley
M10 Nylon Locknut
M10 Large Zinc Washer
Wheel Snap Ring
Flange Screw
M4 x 16mm Screw
M10 x 25mm Screw
M10 x 25mm Button Screw
M10 x 89mm Button Bolt
M10 x 49mm Button Bolt
M10 x 54mm Button Bolt
M10 x 48mm Button Bolt
M3 x 19mm Screw
M5 x 16mm Screw
M8 x 19mm Button Screw
Pedal Leg Bearing
33mm Spacer
Right Base Bushing
M8 x 51mm Button Screw
M10 x 75mm Patch Screw
M3 Nut
M10 x 78mm Button Screw
M8 Nylon Locknut
M8 x 36mm Button Bolt
M6 x 16mm Flat Head Screw
Pulley Housing
16mm Spacer
Upper Pulley Plate
M5 Nut

Key No.

Qty.

109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154

4
4
2
3
3
4
1
2
2
2
4
1
1
1
2
1
4
2
8
4
1
8
4
2
2
1
6
4
2
2
6
6
4
2
4
2
1
1
4
1
2
1
2
1
4
2

Description
Short Wheel Axle
Wheel Bearing
98mm Spacer
51mm Spacer
Long Wheel Axle
M10 Split Washer
Push Link
Spring
M4 x 25mm Screw
Pulley Strap
M4 x 12mm Round Head Screw
Power Plug-in
M10 x 58mm Button Bolt
M10 x 32mm Button Bolt
13mm Spacer
76mm Spacer
M8 x 15mm Screw
Clamp
M6 Nylon Locknuts
M5 Nylon Locknut
M10 x 75mm Button Bolt
M6 x 16mm Screw
M4 x 5mm Screw
M6 x 90mm Bolt
M6 x 112mm Bolt
M10 x 116mm Button Bolt
M10 x 25mm Patch Screw
M10 x 112mm Button Bolt
M4 x 12mm Screw
M10 x 16mm Button Screw
M8 Washer
M8 Split Washer
Pedal Leg Bushing
M8 x 40mm Button Screw
M6 x 29mm Flat Head Screw
M5 x 21mm Flat Head Screw
Reed Switch
Magnet
M6 x 10mm Button Screw
M8 x 58mm Button Screw
M10 x 78mm Carriage Bolt
M6 x 35mm Bolt
M6 Nut
Lower Wire Harness
8mm Spacer
Upright Stabilizer Cap

Key No. Qty.
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
#
#
#
#

2
1
6
1
2
2
6
1
2
2
1
1
4
9
1
1
2
2
1
1
2
2
2
1
2
2
1
4
2
2
1
6
1
1
1
1
2
1
1
1
2
1
1
1
1
2

Description
Crank Snap Ring
Flywheel Snap Ring
Cable Clip
Ankle Strap
Wire Harness
Hand Strap
M10 Washer
Rope
Short Cable
Long Cable
Transformer
M4 x 35mm Screw
Finger Guard
M10 Jam Nut
M4 Nylon Locknut
Reed Sensor
M6 x 25mm Screw
15mm Spacer
11mm Spacer
Extended Hub Pulley
Extension Strap
Plastic Washer
M10 Split Zinc Washer
Pulley Zinc Washer
M5 x 20mm Screw
Plastic Spacer
Reed Switch Plate
M5 Washer
Short Handgrip
Long Handgrip
Belt
M10 Large Black Washer
Sensor Wire Harness
Upper Wire Harness
M10 x 83mm Bolt Set
98mm Large Spacer
Rope Cover
Link
Lower Clamp
Upper Clamp
M13 Washer
M8 x 42mm Button Screw
User’s Manual
Exercise Guide
Exercise Video
Allen Wrench

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts. If a part is missing, call toll-free
1-888-533-1333.

EXPLODED DRAWING A—Model No. 831.159951
30

R0305A

180 67

143
66

143
143

153

18
127

29
153

185

29
127

85
85

66
70

23
117

84 95
31 95

67
84

155
142

148

117

102

146

24
108 108

147

147
156

39
81
171

34
130
130

109

179

128

93
182

83
65

65
83
63

128
81
47 150

65
112
113

130

36
14 19

83 65
112
113

140

196 145
181
126
147 32
47 85
81
46 81
195

179
129

35 108

180
30

155

130

83
85

151

4
40

195

81
46

85
85

149

152

EXPLODED DRAWING B—Model No. 831.159951

R0305A

90 58
50

167

50 42

163

105

161

167

81
157

131

164

161

163 81

158

50
99
52

11
175

131

103

160

102 85
103

71
165

102

3
135
130

164

161

102

22
161

81
80

183
184

135

159
187

188
94

74
139
95

167
105

102
85
103

130

167

103

140

139
140
98

141 110 43
110
141

28 48

154

141

110 43
72
110
141

85
5

85
8
140
98
95

101

114

154

139
98

139
140

6
73

EXPLODED DRAWING C—Model No. 831.159951

R0305A

85
119

125
139

119

51
122

137

139
51173

174

191

168
178
62
168
15

162
85

125

119
85

191

144
194

168

131
13

90
87

186

114 186
118 78
37

86
86 168 82
86
82
82
82
82

48
85
97

48
85

119

162
193 192

186 161
81 78
127
107

168

96
161
50
134 75

137

21
81 127
118
170
51 81
168 123
85
52
186
55
61
166
133
169 90
126
12
127
131 104
77
123
186
189 177
114
138
90 56 53
61
79
100
176
87135
124
176 104
57
177
116
1
100
138
168 106
53
60
92
76
56
86
132
115
82
57
60 92
120
135 111
100 60
106
86
85
82
190
92
59
168
106
51
136
172
82
172
136
111 86
69
86
121
136

132
88
189

FULL 90-DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
ELLIPTICAL TRAINER EXERCISER, contact the nearest Sears Service Center throughout the United
States and Sears will repair or replace the ELLIPTICAL TRAINER EXERCISER, free of charge.
This warranty does not apply when the ELLIPTICAL TRAINER EXERCISER is used commercially or for
rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 60179

Part No. 221997 R0305A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 30
Producer                        : QuarkXPress(tm) 6.5
Title                           : 159951-221997
Create Date                     : 2005:03:16 09:08:10
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (PANTONE 420 C).%%+ (PANTONE 877 C).%%+ (PANTONE 485 C).%%+ (PANTONE 151 C).%%CMYKCustomColor: 0 0 0 .15 (PANTONE 420 C).%%+ 0 0 0 .4 (PANTONE 877 C).%%+ 0 .95 1 0 (PANTONE 485 C).%%+ 0 .48 .95 0 (PANTONE 151 C).%%EndComments
Creator                         : QuarkXPress(tm) 6.5

EXIF Metadata provided by EXIF.tools

Proform 159951 Crossover Elliptical Trainer Users Manual 221997

Proform-159951-Owner-S-Manual proform-159951-owner-s-manual

Navigation menu

Versions of this User Manual:

Views

Navigation