Proform 307541 415 Crosswalk Treadmill Users Manual *294060 204705

Proform-307541-Owner-S-Manual proform-307541-owner-s-manual

2015-04-13

: Proform Proform-307541-415-Crosswalk-Treadmill-Users-Manual-697646 proform-307541-415-crosswalk-treadmill-users-manual-697646 proform pdf

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

Model No. 30754.1
Serial No.

USER'S MANUAL

Write the serial number in the space
above for future reference.

Serial
Number
Decal

QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE DO
NOT CONTACT THE STORE. For
assistance, contact our Customer
Service Department.
CALL TOLL-FREE:

1-888-936-4266
Mon.–Fri., 8:00 until 17:00 EST
(excluding holidays)
OR E-MAIL US:
customerservice@iconcanada.ca

CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.

Visit our website at
www.proform.com

TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

WARNING DECAL PLACEMENT
The decals shown here have been applied in the locations shown. If a decal
is missing, or if it is not legible, call
the telephone number on the front
cover of this manual and request a
free replacement decal. Apply the
decal in the location shown. Note:
The decals may not be shown at actual size.

IMPORTANT PRECAUTIONS
WARNING:

To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons
with pre-existing health problems.

suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.

2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.

12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11.

3. Use the treadmill only as described.

13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.

4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.

14. Keep the power cord and the surge suppressor away from heated surfaces.

5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.

15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 18 if the treadmill is
not working properly.)

6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.

16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 13).

8. The treadmill should be used only by persons
weighing 250 lbs. (113 kg) or less.

17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails or crosswalk arms while using the
treadmill.

9. Never allow more than one person on the
treadmill at a time.

18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.

10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.

19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.

11. When connecting the power cord (see page
11), plug the power cord into a surge suppressor (not included) and plug the surge

24. Inspect and properly tighten all parts of the
treadmill regularly.

20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)

25.

DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.

21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 17.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.

26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.

22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. Never insert any object into any opening on
the treadmill.

SAVE THESE INSTRUCTIONS

BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
CROSSWALK 415 treadmill. The CROSSWALK 415
treadmill offers an impressive array of features designed
to make your workouts at home more enjoyable and effective. And when you’re not exercising, the unique
CROSSWALK 415 treadmill can be folded up, requiring
less than half the floor space of other treadmills.

this manual, please see the front cover of this manual.
To help us assist you, note the product model number
and serial number before contacting us. The model
number and the location of the serial number decal are
shown on the front cover of this manual.
er decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.

For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading

Crosswalk Arm

Book Holder

Accessory Tray

Console
Pulse Sensor

Handrail

Key/Clip

Storage Latch

Upright
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail

Cushioned Walking Platform

Rear Roller
Adjustment Bolts

ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex key
adjustable wrench
.

and your own Phillips screwdriver

, and

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to
one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do
not use power tools for assembly.

M8 Star
Washer (10)–4

M4 x 13mm
Screw (3)–1

M4 x 25mm
Screw (2)–4

M4 x 19mm
Screw (1)–6

M8 x 25mm Bolt (6)–4

M10 Star
Washer (8)–8
Base Pad Spacer
(104)–2

1/4" Washer
(9)–4

1/4" x 3 1/2" Bolt (4)–4

M10 x 96mm Bolt (5)–4

Bolt Spacer (79)–4

1. Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (48) so that the treadmill is more stable;
do not fully fold the Frame yet.

1
B
Tie

Remove and discard the two indicated bolts (A)
and the shipping bracket (B). Cut the tie securing
the Upright Wire (77) to the Base (85). Locate
the tie in the indicated hole in the Base, and use
the tie to pull the Upright Wire out of the hole.

Hole
81

Attach a Base Pad (81) to the Base (85) in the
location shown with a Base Pad Spacer (104)
and an M4 x 25mm Screw (2). Then, attach another Base Pad (81) with only an M4 x 25mm
Screw (2).

104

81
2

2. Remove the M10 Nut (33), the M10 x 50mm Bolt
(27), and the shipping bracket (C) from the Base
(85). Attach a Wheel (86) with the Bolt and the
Nut that you just removed. Do not overtighten
the Nut; the Wheel must turn freely. Discard
the shipping bracket.

2
Tie

Cut the tie off the Upright Wire (77).

C
33

3. Identify the Right Upright (78) and the Right
Upright Spacer (80), which are marked with
stickers. Insert the Upright Wire (77) through the
Right Upright Spacer as shown.

Tie
78
77

See the inset drawing. Tie the wire tie in the
Right Upright (78) securely around the end of
the Upright Wire (77). With the help of a second
person, hold the Right Upright near the Base
(85). Then, pull the other end of the wire tie until
the Upright Wire is routed completely through
the Right Upright.

77
80
85
82

Press a Base Endcap (82) into the Base (85).
78
77

4. Hold a Bolt Spacer (79) inside the lower end of
the Right Upright (78). Insert an M10 x 96mm
Bolt (5) with an M10 Star Washer (8) into the
Right Upright and the Bolt Spacer. Repeat this
step with another Bolt Spacer (79), an M10 x
96mm Bolt (5), and an M10 Star Washer (8).

Wire
Tie

5
78
8
77

Hold the Right Upright Spacer (80) and the
Right Upright (78) against the Base (85). Be
careful not to pinch the Upright Wire (77).
Finger tighten the M10 x 96mm Bolts (5); do not
fully tighten the Bolts yet.

85
79
80

5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (48) so the treadmill is more stable; do
not fully fold the Frame yet.

5
B
A

Remove and discard the two indicated bolts (A)
and the shipping bracket (B).

85
81

Attach a Base Pad (81) to the Base (85) in the
location shown with a Base Pad Spacer (104)
and an M4 x 25mm Screw (2). Then, attach another Base Pad (81) with only an M4 x 25mm
Screw (2).

48
27

2
104
86

Remove the M10 Nut (33), the M10 x 50mm
Bolt (27), and the shipping bracket (C) from the
Base (85). Attach a Wheel (86) with the Bolt and
the Nut that you just removed. Do not overtighten the Nut; the Wheel must turn freely.
Discard the shipping bracket.

81
C
33

6. With the help of a second person, hold a Bolt
Spacer (79) inside the lower end of the Left
Upright (73). Insert an M10 x 96mm Bolt (5) with
an M10 Star Washer (8) into the Left Upright
and the Bolt Spacer. Repeat this step with a
second Bolt Spacer (79), an M10 x 96mm Bolt
(5), and an M10 Star Washer (8).

6
73

5
8
83

Orient the Left Upright (73) and the Left Upright
Spacer (83) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(85). Finger tighten the M10 x 96mm Bolts (5);
do not fully tighten the Bolts yet.

79
82

Press a Base Endcap (82) into the Base (85).
With the help of a second person, tip the treadmill so that the Base (85) is flat on the floor.

7. Set the Console (87) face down on a soft surface to avoid scratching the Console. Identify
the Right Handrail (90), which has a large hole
in the location shown. Attach the console ground
wire to the Right Handrail with an M4 x 13mm
Screw (3).

7
90

Console
Wire

Large Hole
1

Console
Ground Wire

Insert the console wire into the large hole in the
Right Handrail (90) and out of the top as shown.
Attach the Right Handrail with three M4 x 19mm
Screws (1). Make sure that no wires are
pinched. Start all three Screws before tightening any of them; do not overtighten them.

Attach the Left Handrail (not shown) in the
same way. Note: There are no wires on the
left side.

8. Have a second person hold the console assembly near the Right Upright (78). Remove the wire
tie from the Upright Wire (77) and console wire.

Console
Assembly

Connect the Upright Wire (77) to the console
wire. The connectors should slide together
easily and snap into place. If they do not, turn
one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY,
THE CONSOLE MAY BE DAMAGED WHEN
THE POWER IS TURNED ON. Then, insert the
connectors into the Right Upright (78).
Console Wire

Set the console assembly on the Right Upright
(78) and the Left Upright (not shown). Make sure
that no wires are pinched.

77
77
78

9. Finger tighten two M8 x 25mm Bolts (6) with two
M8 Star Washers (10) into the Left Upright (73)
and the Left Handrail (89).

9
89

Next, finger tighten two M8 x 25mm Bolts (6)
with two M8 Star Washers (10) into the Right
Upright (78) and the Right Handrail (90). Then,
tighten all four Handrail Bolts.

6
6

See steps 4 and 6. Tighten the four M10 x
96mm Bolts (5).

73
6

10
6

10
78

10. Press the Latch Insert (70) into the Left Upright
(73).

10
Knob

Remove the knob from the pin. Make sure that
the collar and the spring are on the pin.
Insert the pin into the Latch Insert (70), and
tighten the knob back onto the pin.

70
Spring
Collar
Pin
73

11. Attach the Left Crosswalk Arm (71) to the Left
Upright (73) with two M10 Star Washers (8), two
1/4" Washers (9), and two 1/4" x 3 1/2" Bolts (4).
Make sure that the Left Crosswalk Arm is on
the side of the Console (87) shown.

Attach the Right Crosswalk Arm (not shown)
in the same way.

87
71
73
8

9
4

12. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt (see
page 19).

OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT

plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.

Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.

This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.

HOW TO PLUG IN THE POWER CORD

DANGER:

Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.

The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor

Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).

Grounding Pin

Grounding Pin
Grounded Outlet

Grounding Plug

2
Grounded Outlet Box

Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.

Adapter

Surge Suppressor

Lug
Metal Screw

The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.

This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding

CONSOLE DIAGRAM

Note: If there are sheets of clear plastic on the console, remove the plastic.

Key
Clip

FEATURES OF THE CONSOLE

To use the manual mode of the console, follow the
steps beginning on page 13. To use a preset workout, see page 15.

The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable.

Note: If there is a sheet of clear plastic on the console,
remove the plastic. To prevent damage to the walking
platform, wear clean athletic shoes while using the
treadmill. The first time you use the treadmill, observe
the alignment of the walking belt, and center the walking belt if necessary (see page 19).

When you use the manual mode, you can change the
speed and incline of the treadmill with the touch of a
button. As you exercise, the console will display instant
exercise feedback. You can even measure your heart
rate using the handgrip pulse sensor.

Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
16. Note: For simplicity, all instructions in this section
refer to miles.

In addition, the console offers six iFit custom-fit preset
workouts, three of these use the crosswalk arms. Each
workout automatically controls the speed and incline of
the treadmill as it guides you through an effective exercise session.

HOW TO TURN ON THE POWER

HOW TO USE THE MANUAL MODE

IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.

1. Insert the key into the console.

Plug in the power cord (see
page 11). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Switch the circuit
breaker to the reset position.

See HOW TO TURN ON THE POWER to the left.
2. Select the manual mode.
When the key is inserted, the manual mode will be
selected. If a preset workout has been selected, remove the key and then reinsert it.

Reset
Position

3. Start the walking belt.
To start the walking belt, press the Go button, the
Speed increase button, or one of the speed buttons
numbered 2 through 10.

IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
16 to turn off the demo mode.

If you press the Go button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase and
decrease buttons. Each time you press a button,
the speed setting will change by 0.1 mph; if you
hold down a button, the speed setting will change
in increments of 0.5 mph. Note: After you press a
button, it may take a moment for the walking belt to
reach the selected speed setting.

Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 12)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.

If you press one of the numbered speed buttons, the
walking belt will gradually increase in speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To restart
the walking belt, press the Go button or the Speed
increase button.
4. Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline increase or decrease buttons. Each time
you press the Incline increase or decrease button, the incline will change by 0.5%. Note: After you
press a button, it may take a moment for the treadmill to reach the selected incline setting.

5. Follow your progress with the displays.

6. Measure your heart rate if desired.

The lower left display—
As you exercise, the
lower left display can
show the elapsed time
and the distance that you
have walked or run. The
lower left display will also show the incline of the
treadmill each time the incline level changes.

Before using the
handgrip pulse
sensor, remove
the sheets of
clear plastic from
the metal contacts on the pulse
bar. In addition,
make sure that
your hands are clean.

The lower right display—The lower right
display can show the approximate number of
calories that you have
burned and the speed of
the walking belt. The display also shows your heart
rate when you use the handgrip pulse sensor (see
step 6).
The upper display—The upper
display can show
the elapsed time,
the distance that
you have walked
or run, the approximate number of calories that you
have burned, or the speed of the walking belt. Press
the Display button repeatedly until the upper display
shows the information that you are most interested
in viewing. Note: While information is shown in the
upper display, the same information will not be
shown in the lower displays.

Contacts

To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on the
metal contacts. Avoid moving your hands. When
your pulse is detected, a heart symbol in the lower
right display will flash each time your heart beats,
one or two dashes will appear, and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
7. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical components may wear prematurely.

To reset the displays, press the Stop button, remove the key, and then reinsert the key.

HOW TO USE A PRESET WORKOUT

Tones will sound at the end of each segment.
Three seconds before the speed and/or incline of
the treadmill is about to change, the Speed display
and/or Incline display will flash and a series of tones
will sound to alert you. The treadmill will then automatically adjust to the speed and/or incline settings
for the next segment.

1. Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 13.
2. Select a preset workout.

If you have selected workout 4, 5 or 6, you will be
prompted to use the crosswalk arms. When the
crosswalk indicator lights up, move the crosswalk
arms forward and backward as you walk on the
treadmill. This action exercises your arms, shoulders, and back for a total body workout,

To select a preset workout, press the Select
Workout button repeatedly until the number of
the desired workout appears in the upper display. Note: The name, number, and profile of each
workout is listed on the console.

The workout will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.

When you select a preset workout, the incline level
of the workout will flash in the lower left display, the
speed setting will flash in the upper display, and
then the workout length will appear in the lower left
display.

If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the Speed or Incline
buttons. Note: When the next segment of the
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.

3. Select length of workout if desired.
If you have selected workout 1, 2, or 3, you can set
the length of the workout to a time between 15 and
45 minutes, in increments of 5 minutes. To set the
length of the workout press the Set Time increase
or decrease button until the desired time is selected. The new workout settings will appear in the
displays.
4. Press the Go button or the Speed increase button to start the workout.

To stop the workout at any time, press the Stop
button. To restart the workout, press the Go button.
The walking belt will begin to move at 1 mph. When
the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline
settings for the next segment.
5. Follow your progress with the displays.
See step 5 on page 14.

A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings of the workout. Hold the handrails and
begin walking.
Each workout is divided into 30 one-minute segments, unless you have changed the length of the
workout (see step 3). One speed setting and one
incline setting are programmed for each segment.
Note: The same speed setting and/or incline setting
may be programmed for two or more consecutive
segments.

6. Measure your heart rate if desired.
See step 6 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 7 on page 14.

THE INFORMATION MODE

HOW TO USE THE CROSSWALK ARMS

The console features an information mode that keeps
track of the total distance that the walking belt has
moved and the total number of hours that the treadmill
has been used. The information mode also allows you
to select a measurement system of miles or kilometers
and turn on and off the display demo mode.

As you walk on the treadmill, you can hold the
handrails or use the crosswalk arms. To exercise your
arms, shoulders, and back for a total body workout,
move the crosswalk arms forward and back as you
walk on the treadmill.
To vary the intensity of your upper body exercise, the
resistance of the crosswalk arms can be adjusted. To
increase the resistance, turn the resistance knobs
clockwise; to decrease the resistance, turn the knobs
counterclockwise.

To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
An “E” for English miles or
an “M” for metric kilometers
will appear in the lower right
display. Press the Speed increase button to change the
unit of measurement if desired.

Upper Body
Arms

The lower left display will
show the total number of
miles (or kilometers) that the
walking belt has moved.

The upper display will show
the total number of hours the
treadmill has been used.

Resistance
Knobs

Note: The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. While the demo mode is turned on, the console
will function normally when you plug in the power cord,
switch the circuit breaker to the reset position, and insert the key into the console. However, when you remove the key, the displays will remain lit, although the
buttons will not function. If the demo mode is turned on,
a “d” will appear in the lower right display while the information mode is selected. To turn on or off the demo
mode, press the Speed decrease button.
To exit the information mode, remove the key from the
console.

HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the pin is
aligned with the gap between the frame and platform,
and then slowly release the latch knob. Make sure that
the latch pin is fully inserted into the gap.
Frame
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).

Latch
Knob
Pin

HOW TO MOVE THE TREADMILL
Frame
Before moving the treadmill, convert it to the storage position
as described above. Make sure that the frame is held securely by the latch pin.
Handrail
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheels

Base

3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left. It may be necessary to
push the frame forward as you pull the knob to the left. Pivot the frame downward and release the latch knob.
2. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your legs and keep your back straight.

TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call the telephone number listed on
the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppressor that meets all of the specifications described on page 11. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.

Reset

Tripped

PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
THE POWER CORD. Remove the three M4 x
19mm Screws (13) and carefully pivot the Hood
(53) off.

Locate the Reed Switch (54) and the Magnet (42)
on the left side of the Pulley (44). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4 x 19mm Screw (1), move the
Reed Switch slightly, and then retighten the Screw.
Reattach the Hood, and run the treadmill for a few
minutes to check for a correct speed reading.

1/8 in.
1
54

42
44

Top
View

PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 16 to turn off the demo mode.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to 7
cm) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

2–3 in.

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left rear roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side
of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt
centered. Then, plug in the power cord, insert the
key, and carefully walk on the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened.

PROBLEM: The crosswalk arms squeak during use
SOLUTION: a. (Note: Correcting this problem requires a small
amount of white marine grease, available at hardware stores.) Turn the Resistance Knob (A) counterclockwise and remove it. Next, remove the
Resistance Cone (B) and the Crosswalk Arm (76),
along with the Resistance Plate (C), Washers (D),
Spring Washer (E), Thrust Washers (F), and Thrust
Bearing (G). (Note: If the Resistance Plate [C]
comes out of the Resistance Cone [B], press it back
in.) Apply a thin layer of white marine grease to the
outer surface of the Resistance Cone (B). Then,
reattach all parts in the order shown at the right.

76
B
F
E
C

G
D

EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.

WARNING:

Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over the age of 35 or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.

Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.

These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.

WORKOUT GUIDELINES

EXERCISE INTENSITY

Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.

Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.

Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY

To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.

To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.

PART LIST—Model No. 30754.1

R0607A

To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

15
4
1
4
4
4
1
4
4
4
5
12
3
2
2
1
2
1
1
2
1
7
8
2
2
1
2
4
2
2
1
2
4
2
2
4
3
4
1
2
2
1
1
1
1
1
1
1
1
2

Description

Key No. Qty.

M4 x 19mm Screw
M4 x 25mm Screw
M4 x 13mm Screw
1/4" x 3 1/2" Bolt
M10 x 96mm Bolt
M8 x 25mm Bolt
3/8" Star Washer
M10 Star Washer
1/4" Washer
M8 Star Washer
M4 x 13mm Washer Head Screw
M4 x 16mm Screw
M4 x 19mm Washer Head Screw
M8 x 30mm Screw
M8 x 90mm Screw
M10 x 34mm Bolt
M6 x 70mm Bolt
3/8" x 1 3/4" Bolt
3/8" x 1 1/2" Bolt
3/8" x 1" Bolt
M6 x 45mm Bolt
M4 x 13mm Ground Screw
M5 x 25mm Screw
1/4" x 3/8" Bolt
3/8" x 3/4" Bolt
3/8" x 4" Bolt
M10 x 50mm Bolt
M4 x 13mm Screw
M6 Lock Washer
M6 Washer
3/8" Nut
3/8" Motor Nut
M10 Nut
M8 Nut
M8 Flange Nut
3/8" Lock Nut
Hood Clip
Cage Nut
Left Foot Rail
Walking Platform Cushion
Belt Guide
Magnet
Motor Belt
Front Roller/Pulley
Walking Belt
Walking Platform
Right Foot Rail
Frame
Warning Decal, English
Rear Roller Bracket Plate

51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

1
1
1
1
1
2
1
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
4
1
4
2
1
2
1
2
1
1
1
1
4
1
1
1
7
2
2
1
1
1

Description
Left Foot
Right Foot
Hood
Reed Switch
Reed Switch Clip
Frame Spacer
Lift Frame/Roller Ground Wire
Incline Motor
Rear Roller Bracket
Motor
Motor Bracket
Cable Tie
Lift Frame
Filter Wire
Power Cord
Controller
Grommet
Reset/Off Circuit Breaker
Belly Pan
Latch Insert
Left Crosswalk Arm
Latch Pin Assembly
Left Upright
Insert Screw
Crosswalk Arm Insert
Right Crosswalk Arm
Upright Wire
Right Upright
Bolt Spacer
Right Upright Spacer
Base Pad
Base Endcap
Left Upright Spacer
Caution Decal
Base
Wheel
Console
Console Base
Left Handrail
Right Handrail
Handrail Endcap
Cable Tie
Key/Clip
Releasable Tie
8" Cable Tie
Resistance Assembly
Hand Grip
M10 x 30mm Screw
Lift Motor Spacer
Rear Roller

Key No. Qty.
101
102
103
104
105
106
107
108
*

1
1
2
2
1
1
1
1
–

Description

Key No. Qty.

Hex Key
Lift Frame/Base Ground Wire
Frame Endcap
Base Pad Spacer
4mm Hex Key
5mm Hex Key
6mm Hex Key
Warning Decal, French
10" Blue Wire, 2F

–
6" Blue Wire, 2F
*
*
–
4" Blue Wire, M/F
–
6" Red Wire, M/F
*
*
–
6" Black Wire, M/F
*
–
8" Green Wire, F/Ring
*
–
User’s Manual
*These parts are not illustrated.
Specifications are subject to change without notice.

Description

105

106

107

103

101

30 103

100

41
28

108

EXPLODED DRAWING A—Model No. 30754.1
R0607A

EXPLODED DRAWING B—Model No. 30754.1

R0607A

13
53

13
37

25
7
25
60

32
1

55
61

56
33

26
21

31
57

56
33

12
66

65
11
11
11
67
11

22
68

11
12

EXPLODED DRAWING C—Model No. 30754.1

R0607A

6
71

6
70

74
77
8

4
96

10
6

102

20
79

84
81

77
85

104
33
86

2
84

33
86

104
81
2

EXPLODED DRAWING D—Model No. 30754.1

R0607A

88
12
12
22
12
92

12
12
12
91

12
91

12
3

1
89
90
91

1
38

ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING near the end of this manual)

LIMITED WARRANTY
ICON OF CANADA, INC. (ICON) warrants this product to be free from defects in workmanship and material, under normal use and service conditions. The frame is warranted for four (4) years after the date
of purchase. The drive motor is warranted for one (1) year after the date of purchase. Parts and labor
are warranted for one (1) year after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province.
ICON OF CANADA, INC., 900 de l’Industrie, St. Jerôme, QC J7Y 4B8

Part No. 257724 R0607A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 28
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (PANTONE 3005 C).%%+ (PANTONE 430 C).%%CMYKCustomColor: 1 .34 0 .02 (PANTONE 3005 C).%%+ .05 0 0 .45 (PANTONE 430 C).%%EndComments
Producer                        : QuarkXPress(tm) 6.5
Create Date                     : 2007:06:14 15:53:48
Title                           : *294060-204705
Creator                         : QuarkXPress(tm) 6.5

EXIF Metadata provided by EXIF.tools

Proform 307541 415 Crosswalk Treadmill Users Manual *294060 204705

Proform-307541-Owner-S-Manual proform-307541-owner-s-manual

Navigation menu

Versions of this User Manual:

Views

Navigation