Proform Pfsy34150 Fusion 4 0 Lx Weight System Users Manual WESY39240 212817

Proform-Pfsy34150-Owner-S-Manual proform-pfsy34150-owner-s-manual

PFSY3415.0 to the manual d3aea54b-b51e-41fe-a89e-c03defb50b94

2015-04-14

: Proform Proform-Pfsy34150-Fusion-4-0-Lx-Weight-System-Users-Manual-701386 proform-pfsy34150-fusion-4-0-lx-weight-system-users-manual-701386 proform pdf

Open the PDF directly: View PDF .
Page Count: 24

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Model No. PFSY3415.0

Serial No.

Write the serial number in the

space above for future reference.

Serial Number Decal (Under Seat)

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if a part is

damaged or missing, PLEASE

CONTACT OUR CUSTOMER

SERVICE DEPARTMENT

DIRECTLY.

CALL TOLL-FREE:

1-888-533-1333

Mon.–Fri., 6 a.m.–6 p.m. MST

ON THE WEB:

www.proformservice.com

USER’S MANUAL

Visit our website at

www.proform.com

new products, prizes,

fitness tips, and much more!

WARNING DECAL PLACEMENT

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING is attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

PROFORM is a registered trademark of ICON IP

,Inc.

TABLE OF CONTENTS

The decal shown here has been placed on the

weight system. If the decal is missing or illegi-

ble, please call the toll-free telephone number

on the front cover of this manual and order a

free replacement decal. Apply the decal in the

location shown.

1. Read all instructions in this manual and all

warnings on the weight system before using

the weight system. Use the weight system

only as described in this manual.

2. It is the responsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all precautions.

3. The weight system is intended for home use

only. Do not use the weight system in any

commercial, rental, or institutional setting.

4. Keep the weight system indoors, away from

moisture and dust. Place the weight system

on a level surface, with a mat beneath it to

protect the floor or carpet. Make sure that

there is enough clearance around the weight

system to mount, dismount, and use the

weight system.

5. Inspect and properly tighten all parts regular-

ly. Replace any worn parts immediately.

6. Keep children under 12 and pets away from

the weight system at all times.

7. Keep hands and feet away from moving parts.

8. Make sure that the cables remain on the pul-

leys at all times. If the cables bind as you are

exercising, stop immediately and make sure

that the cables are on the pulleys. Replace all

cables at least every two years.

9. Always wear athletic shoes for foot protec-

tion while exercising.

10. Always stand on the foot plate when per-

forming an exercise that could cause the

weight system to tip.

11. The weight system is designed to support a

maximum user weight of 300 pounds.

12. The weight system is designed to be used

only with the included weight. Do not use the

weight system with dumbbells or any other

type of weight to increase the resistance.

13. Always move the seat frame out of the way

when performing squat exercises.

14. Never release the ankle strap, leg lever,

squat bar, leg press, curl bar, or handles

while weights are raised; the weights will fall

with great force.

15. Do not use the weight system with the top

weight pinned in an elevated position.

16. Always secure the weight stack with the lock

pin and lock after exercising to prevent

unauthorized use of the weight system (see

LOCKING THE WEIGHT STACK on page 15).

17. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the weight system.

IMPORTANT PRECAUTIONS

Pulley Housing

Pull-up Handle

Shroud

VKR Frame

Handle

Weight Stack

Right Side

Left Side

Note: The terms “right side” and “left side”

are determined relative to a person sitting on

the bench; they do not correspond to right

and left on the drawings in the manual.

Backrest

Swivel Arm

Leg Lever

Seat

BEFORE YOU BEGIN

Thank you for selecting the versatile PROFORM®

FUSION 4.0 LX weight system. The weight system

offers a selection of weight stations designed to devel-

op every major muscle group of the body. Whether

your goal is to tone your body, build dramatic muscle

size and strength, or improve your cardiovascular sys-

tem, the weight system will help you to achieve the

specific results you want.

For your benefit, read this manual carefully before

using the weight system. If you have questions after

reading this manual, see the front cover of this manu-

al. To help us assist you, please note the product

model number and serial number before calling. The

model number is PFSY3415.0. The serial number can

be found on a decal attached to the weight system

(see the front cover of this manual).

Toavoid a registration fee for any service needed

under warranty, you must register the weight sys-

tem at www.proformservice.com/registration.

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

Curl Pad

ASSEMBLED DIMENSIONS:

Height: 82 in. / 208 cm

Width: 105 in. / 267 cm

Depth: 94 in. / 239 cm

Weight Pin

ASSEMBLY

To hire an authorized service technician to

assemble the weight system, call toll-free

1-800-445-2480.

Before beginning assembly, carefully read the

following information and instructions:

•Because of its weight and size, the weight sys-

tem should be assembled in the location where it

will be used. Make sure that there is enough

clearance to walk around the weight system as

you assemble it.

•Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until assembly is completed.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

•As you assemble the weight system, make sure

all parts are oriented as shown in the drawings.

•Assembly requires two people.

• For help identifying small parts, use the PART

IDENTIFICATION CHART.

Assembly may be require the included grease

and hex key , and the following tools

(not included):

• Two adjustable wrenches

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

• Clear tape or masking tape, and soapy water.

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Make Things Easier for Yourself

Everything in this manual is designed to ensure

that the weight system can be assembled suc-

cessfully by almost anyone. However, the weight

system has many parts and the assembly

process will take time. By setting aside plenty of

time, assembly will go smoothly.

Attach the Rear Stabilizer (5) to the Base (1) with

the two M8 x 76mm Carriage Bolts (59) and two

M8 Nylon Locknuts (74).

See the inset drawing. Press the two Base Caps

(38) onto the Base (1).

559

Before beginning assembly, make sure you

understand the information in the box

above. For help identifying small parts, use

the PART IDENTIFICATION CHART in the

center of this manual.

2. Press the 110mm Round Inner Cap (42) into the

Upright (3).

Set the Upright (3) onto the Base (1). Have a sec-

ond person hold the Upright until this step is com-

pleted.

Attach the Upright (3) to the Base (1) with the

three M8 x 45mm Bolts (57), three M8 Nylon

Locknuts (74), and four M10 x 25mm Screws (58).

3. Attach the Base Plate (2) to the Base (1) with the

four M4 x 40mm Screws (46), and two M4 x

64mm Screws (81).

74 1

4. Insert the Weight Tube (11) into a Weight (17).

Make sure the indicated slot in the Weight is

oriented as shown. Center the Roll Pin (54) into

the indicated hole in the Weight Tube. Note: The

Roll Pin must be below the Weight.

5. Orient the two Weight Guides (10) with the indi-

cated hole closer to the bottom (see the inset

drawing).

Insert the two Weight Guides (10) into the indicat-

ed holes in the Base (1). Attach the Weight

Guides with two M8 x 115mm Bolts (76), four M8

Washers (72), two 38mm Spacers (48), and two

M8 Nylon Locknuts (74).

Slide the two Weight Bumpers (50) onto the

Weight Guides (10). Next, slide eleven Weights

(17) onto the Weight Guides one at a time. Make

sure the indicated slot in each Weight is ori-

ented as shown. Then, slide the Weight Tube

(11) and Weight (17) onto the Weight Guides.

Slot

Holes

6. Slide three M6 Washers (78) onto three M6 x

140mm Screws (79) and insert the Screws into

the Upright (3) through the indicated holes.

Orient the VKR Bumper (95) with the wide end on

top. Attach the VKR Bumper to the Upright (3)

with two M4 x 16mm Screws (70).

Attach the VKR Pin (101) to the Upright (3) with

an M4 x 16mm Screw (70).

Set the Shroud (13) onto the Base (1). Attach the

Bottom Cover (14) and the Shroud to the Base

with two M4 x 16mm Screws (70).

7. Grease the M10 x 168mm Button Bolt (99).

Attach the VKR Frame (82) to the Upright (3) with

the Bolt and an M10 Nylon Locknut (73). Do not

overtighten the Locknut; the VKR Frame must

be able to pivot easily.

Engage the VKR Pin (101) into the VKR Frame

(82) and the Upright (3).

313

14 70

Wide

End

73 82

Grease

101

8. Slide the Top Frame (4) onto the Weight Guides

(10). Attach the Top Frame to the Weight Guides

with two M8 x 89mm Bolts (64), four M8 Washers

(72), two 25mm Spacers (47), and two M8 Nylon

Locknuts (74). Donot tighten the Locknuts.

Attach the Top Frame (4) to the Upright (3) with

four M10 x 25mm Screws (58). Do not tighten

the Screws.

Attach the Top Cover (15) to the Shroud (13) and

Top Frame (4) with two M4 x 16mm Screws (70).

Tighten the two M8 Nylon Locknuts (74) and

the four M10 x 25mm Screws (58).

9. Slide a Pull-up Cap (39) onto a Pull-up Handle

(96). Insert the Handle into the Top Frame (4) and

press the Cap onto the Top Frame.

Attach the Pull-up Handle (96) to the Top Frame

(4) with two M10 x 80mm Button Bolts (97), two

M10 Washers (71), two M10 Split Washers (98),

and two M10 Nylon Locknuts (73).

Repeat this step with the other Pull-up Handle

(96).

10. Attach an Eyehook (66) to the Top Frame (4) with

an M8 Washer (72) and an M8 Nylon Locknut

(74). Do not overtighten the Locknut; the

Eyehook must rotate freely.

Repeat this step with the other Eyehook (66).

370

96 39

11. Attach the Press Arm (8) without the wire to the

Upright (3) with four M10 x 25mm Screws (58).

Remove the M4 x 5mm Screw (69) and the

Swivel Arm (16). Route the Press Arm Cable (30)

through the Swivel Arm and the Press Arm (8) as

shown.

Reattach the Swivel Arm (16) to the Press Arm

(8) with the M4 x 5mm Screw (69).

13. Attach a 2 3/4" Pulley (23) to the left Press Arm

(8) with an M10 x 53mm Button Bolt (61), two

M10 Washers (71), two 5mm Spacers (25), two

Finger Guards (27), and an M10 Nylon Locknut

(73). See the inset drawing. Orient the Finger

Guards and Pulley as shown. Make sure the

Press Arm Cable (30) is in the groove of the

Pulley.

12. Attach a “V”-pulley (22) to a Swivel Arm (16) with

an M10 x 64mm Button Bolt (75), two M10

Washers (71), two 5mm Spacers (25), and an

M10 Nylon Locknut (73). Make sure the Press

Arm Cable (30) is routed under the indicated

welded rods.

71 71

Welded

Rod

Welded

Rod

27 27

14. Wrap the Press Arm Cable (30) over a 3 1/2"

Pulley (24) and route the Cable through the Top

Cover (15) as shown.

Attach the 3 1/2" Pulley (24) and a Cable Trap

(28) to the Top Frame (4) with an M10 x 45mm

Bolt (65) and an M10 Nylon Locknut (73). Make

sure the Cable Trap is oriented to hold the

Press Arm Cable (30) in the groove of the

Pulley.

73 65

15. Wrap the Press Arm Cable (30) over a 3 1/2"

Pulley (24). Attach the Pulley and a Cable Trap

(28) to the Top Frame (4) with an M10 x 45mm

Bolt (65) and an M10 Nylon Locknut (73). Make

sure the Cable Trap is oriented to hold the

Cable in the groove of the Pulley.

16. Wrap the Press Arm Cable (30) under a 3 1/2"

Pulley (24). Attach the Pulley, a Cable Trap (28),

and two Half Finger Guards (26) to the Weight

Tube (11) with an M10 x 48mm Bolt (62) and an

M10 Nylon Locknut (73) at the indicated hole.

Make sure the Finger Guards are oriented as

shown and are on the outside of the Weight

Tube. Make sure the Cable Trap is oriented to

hold the Cable in the groove of the Pulley.

26 24

17. Wrap the Press Arm Cable (30) over a 3 1/2"

Pulley (24). Attach the Pulley and a Cable Trap

(28) to the Top Frame (4) with an M10 x 45mm

Bolt (65) and an M10 Nylon Locknut (73). Make

sure the Cable Trap is oriented to hold the

Cable in the groove of the Pulley.

18. Route the Press Arm Cable (30) through the Top

Cover (15).

Wrap the Press Arm Cable (30) over a 3 1/2"

Pulley (24). Attach the Pulley and a Cable Trap

(28) to the Top Frame (4) with an M10 x 45mm

Bolt (65) and an M10 Nylon Locknut (73). Make

sure the Cable Trap is oriented to hold the

Cable in the groove of the Pulley.

24 30 15

24 4

19. Attach the Press Arm (8) with the wire to the

Upright (3) with four M10 x 25mm Screws (58).

Remove the M4 x 5mm Screw (69) and the

Swivel Arm (16).

Using the wire that is inserted into the Press Arm

(8), route the Press Arm Cable (30) through the

Press Arm as shown. Route the Cable through

the Swivel Arm (16).

Reattach the Swivel Arm (16) to the Press Arm

(8) with the M4 x 5mm Screw (69).

20. Attach a 2 3/4" Pulley (23) to the right Press Arm

(8) with an M10 x 53mm Button Bolt (61), two

M10 Washers (71), two 5mm Spacers (25), two

Finger Guards (27), and an M10 Nylon Locknut

(73). See the inset drawing. Orient the Finger

Guards and Pulley as shown. Make sure the

Press Arm Cable (30) is in the groove of the

Pulley.

21. Make sure the Press Arm Cable (30) is routed

under the indicated welded rods.

Attach a “V”-pulley (22) to the Swivel Arm (16)

with an M10 x 64mm Button Bolt (75), two M10

Washers (71), two 5mm Spacers (25), and an

M10 Nylon Locknut (73).

30 22

23 27

Welded

Rods

2727

22. Attach the Backrest (18) and the Backrest Base

(88) to the Upright (3) with the two M6 x 25mm

Screws (60) and the indicated M6 x 140mm

Screw (79).

60 60

23. Attach the Headrest (90) and the Headrest Base

(89) to the Upright (3) with the two indicated M6 x

140mm Screw (79).

24. Attach the Seat (19) and the Seat Base (91) to

the Seat Frame (6) with two M6 x 25mm Screws

(60), an M6 x 87mm Screw (68), and an M6

Washer (78).

Hook the Seat Frame (6) onto the Upright (3) at

the indicated location.

24 19

78 60

26. Slide two Foam Pads (21) onto the Seat Frame

(6).

Slide a Pad Tube (20) through a hole in the Leg

Lever (7). Slide two Foam Pads (21) onto the Pad

Tube.

25. Attach the Bumper (49) to the Leg Lever (7) with

an M4 x 16mm Screw (70).

Apply grease to an M10 x 71mm Bolt (67). Attach

the Leg Lever (7) to the Seat Frame (6) with the

Bolt and an M10 Nylon Locknut (73). Do not

overtighten the Bolt; the Leg Lever must be

able to pivot easily.

Grease

770

27. Slide an Arm Pad Base (83) and an Arm Pad (84)

onto the VKR Frame (82). Attach the Arm Pad

and Base to the Frame with two M6 x 73mm

Screws (103) and two M6 Washers (78).

Repeat this step on the other side of the VKR

Frame (82).

103

20 21

28. Attach the Curl Pad (87) and the Curl Pad Base

(86) to the Curl Post (85) with two M6 x 25mm

Screws (60).

29. Make sure that all parts have been properly

tightened before the resistance system is

used.

This section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 18 for

important information about how to get the most benefit from your exercise program. Also, refer to the accom-

panying exercise guide to see the correct form for each exercise.

Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts imme-

diately. The weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use

solvents.

ATTACHING THE PULLEY HOUSINGS

Touse a high pulley,slide the hook on the Pulley

Housing (32) onto an Eyehook (66) on the Top Frame

(4). Attach the end of the Extension Cable (31) without

the ball to the end of the Press Arm Cable (30) with a

Cable Clip (37). Attach the other Pulley Housing in

the same manner.

See the inset drawing A. Touse the leg lever (not

shown), hook the Pulley Housings (32) to the hooks

on the Upright (3).

See the inset drawing B. Touse the curl bar (not

shown), hook the Pulley Housings (32) to the hook in

the center of the Base (1). Attach the end of the

Extension Cable (31) without the ball to the end of the

Press Arm Cable (30) with two Cable Clips (37).

See the inset drawing C. Touse the squat bar (not

shown), hook the Pulley Housings (32) to the hooks

on the sides of the Base (1). Note: To use the squat

bar,you must first remove the Seat Frame from

the Upright (See ADJUSTING THE SEAT FRAME

HEIGHT on the next page).

Remove the Pulley Housings (32) when not in use.

66 4

ADJUSTMENTS

ATTACHING THE HANDLES

oattach a Handle (33), first attach the pulley housings

to the weight system (see ATTACHING THE PULLEY

HOUSING on page 14 above). Then, attach the

Handle to an Extension Cable (31) with a Cable Clip

(37). The Handles can be attached to the Press Arm

Cable (30) in the same manner.

The Ankle Strap (not shown) or Squat Bar (not shown)

can be attached to an Extension Cable (31) in the

same manner. For some exercises an Extension Strap

(not shown) should be attached between the Extension

Cable and the accessory with two Cable Clips (37).

ADJUSTING THE SEAT FRAME HEIGHT

To adjust the height of the Seat Frame (6), or to

remove it for exercising with the squat bar, unhook

the Seat Frame from the indicated brackets on the

Upright (3). Hook it onto the other bracket or set it

aside.

Brackets

CHANGING THE WEIGHT SETTING

To change the setting of a weight stack, insert the

Weight Pin (55) under the desired Weight (17). Insert

the Weight Pin so that the bent end touches the

weight stack. Turn the bent end down.

See the WEIGHT RESISTANCE CHART on page 17

for the resistance for each station.

LOCKING THE WEIGHT STACK

To lock the weight stack, insert the Lock Pin (53) into

the indicated hole in a Weight Guide (10). Insert the

Lock (52) through the hole in the Weight Pin and

close the Lock.

Hole

107

731

ATTACHING THE LEG LEVER

Touse the Leg Lever (7), first attach the seat to the

weight system (see ADJUSTING THE SEAT FRAME

HEIGHT on page 15). Then, attach the pulley hous-

ings to the upright (see ATTACHING THE PULLEY

HOUSINGS on page 14). Finally, attach the Extension

Cables (31) to the Chain (107) with two Cable Clips

(37) and attach the Chain to the Leg Lever with anoth-

er Cable Clip. Note: For less resistance, the Leg

Lever can be used with only one Extension Cable

attached to it.

ATTACHING THE CURL PAD

To use the Curl Pad (87), first remove the 51mm

Round Inner Cap (41) from the Seat Frame (6). Then

secure the Curl Post (85) inside the Seat Frame with

the Curl Knob (100).

When the Curl Pad (87) is not being used, the 51mm

Round Inner Cap (41) should be reinserted into the

Seat Frame (6).

ATTACHING THE CURL BAR

To use the Curl Bar (104), first attach the curl pad to

the seat frame (see ATTACHING THE CURL PAD

above). Then, with the pulley housings attached to the

base (see ATTACHING THE PULLEY HOUSINGS on

page 14) attach the Extension Cables (31) to the Leg

Lever (7) with Cable Clips (37). Finally, attach the Curl

Bar to the Leg Lever.

ADJUSTING THE VKR FRAME

To adjust the VKR Frame (82), remove the VKR Pin

(101) from the Frame and the Upright (3). Move the

Frame down to use the Frame to exercise, or up to

the stored position. Reengage the Pin into the Frame

and Upright.

100

104

101

The cable diagram shows the proper routing of

the Press Arm Cable (30). Use the diagram to

make sure that the Cable has been assembled

correctly. If the Cable has not been correctly

routed, the weight system will not function prop-

erly and damage may occur. The numbers show

the correct route for the Cable.

CABLE DIAGRAM

Press Arm Cable (30)

WEIGHT RESISTANCE CHART

The chart below shows the approximate weight resistance for the 12.5 lb. weights. Weight resistance shown is

for each arm. Note: The actual resistance at each station may vary due to differences in individual weight

plates as well as friction between the cables, pulleys, and weight guides.

WEIGHT 1 2 3 4 5 6 7 8 9 10 1112

RESISTANCE 14 23 32 41 50 59 68 77 86 95 102 110

EXERCISE GUIDELINES

THE FOUR BASIC TYPES OF WORKOUTS

Muscle Building

Toincrease the size and strength of your muscles,

push them to a high percentage of their maximum

capacity. Your muscles will adapt and grow as you pro-

gressively increase the intensity of your exercise. You

can adjust the intensity level of an individual exercise

in two ways:

• by changing the amount of weight used

•by changing the number of repetitions or sets per-

formed. (A “repetition” is one complete cycle of an

exercise, such as one sit-up. A “set” is a series of

repetitions.)

The proper amount of weight for each exercise

depends upon the individual user. You must gauge

your limits and select the amount of weight that is right

for you. Begin with 3 sets of 8 repetitions for each

exercise you perform. Rest for 3 minutes after each

set. When you can complete 3 sets of 12 repetitions

without difficulty, increase the amount of weight.

Toning

You can tone your muscles by pushing them to a mod-

erate percentage of their capacity. Select a moderate

amount of weight and increase the number of repeti-

tions in each set. Complete as many sets of 15 to 20

repetitions as possible without discomfort. Rest for 1

minute after each set. Work your muscles by complet-

ing more sets rather than by using high amounts of

weight.

Weight Loss

To lose weight, use a low amount of weight and

increase the number of repetitions in each set.

Exercise for 20 to 30 minutes, resting for a maximum

of 30 seconds between sets.

Cross Training

Cross training is an efficient way to get a complete and

well-balanced fitness program. An example of a bal-

anced program is:

•Plan strength training workouts on Monday,

Wednesday, and Friday.

•Plan 20 to 30 minutes of aerobic exercise, such as

running on a treadmill or riding an elliptical or an

exercise cycle, on Tuesday and Thursday.

•Rest from both strength training and aerobic exercise

for at least one full day each week to give your body

time to regenerate.

The combination of strength training and aerobic exer-

cise will reshape and strengthen your body, plus devel-

op your heart and lungs.

PERSONALIZING YOUR EXERCISE PROGRAM

Determining the exact length of time for each workout,

aswell as the number of repetitions or sets completed,

is an individual matter. It is important to avoid overdo-

ing it during the first few months of your exercise pro-

gram. You should progress at your own pace and be

sensitive to your body’s signals. If you experience pain

or dizziness at any time while exercising, stop immedi-

ately and begin cooling down. Find out what is wrong

before continuing. Remember that adequate rest and a

proper diet are important factors in any exercise pro-

gram.

WARMING UP

Begin each workout with 5 to 10 minutes of stretching

and light exercise to warm up. Warming up prepares

your body for more strenuous exercise by increasing

circulation, raising your body temperature and deliver-

ing more oxygen to your muscles.

WORKING OUT

Each workout should include 6 to 10 different exercis-

es. Select exercises for every major muscle group,

emphasizing areas that you want to develop most. To

give balance and variety to your workouts, vary the

exercises from session to session.

Schedule your workouts for the time of day when your

energy level is the highest. Each workout should be

followed by at least one day of rest. Once you find the

schedule that is right for you, stick with it.

EXERCISE FORM

Maintaining proper form is an essential part of an

effective exercise program. This requires moving

through the full range of motion for each exercise, and

moving only the appropriate parts of the body.

Exercising in an uncontrolled manner will leave you

feeling exhausted. On the exercise guide accompany-

ing this manual you will find photographs showing the

correct form for several exercises, and a list of the

muscles affected. Refer to the muscle chart on the

next page to find the names of the muscles.

The repetitions in each set should be performed

smoothly and without pausing. The exertion stage of

each repetition should last about half as long as the

return stage. Proper breathing is important. Exhale

during the exertion stage of each repetition and inhale

during the return stroke. Never hold your breath.

Rest for a short period of time after each set. The

ideal resting periods are:

•Rest for three minutes after each set for a muscle

building workout.

•Rest for one minute after each set for a toning work-

out.

•Rest for 30 seconds after each set for a weight loss

workout.

Plan to spend the first couple of weeks familiarizing

yourself with the equipment and learning the proper

form for each exercise.

COOLING DOWN

End each workout with 5 to 10 minutes of stretching.

Include stretches for both your arms and legs. Move

slowly as you stretch and do not bounce. Ease into

each stretch gradually and go only as far as you can

without strain. Stretching at the end of each workout

is an effective way to increase flexibility.

STAYING MOTIVATED

For motivation, keep a record of each workout. List the

date, the exercises performed, the resistance used,

and the numbers of sets and repetitions completed.

Record your weight and key body measurements at

the end of every month. Remember, the key to achiev-

ing the greatest results is to make exercise a regular

and enjoyable part of your everyday life.

MUSCLE CHART

A. Sternomastoid (neck)

B. Pectoralis Major (chest)

C. Biceps (front of arm)

D. Obliques (waist)

E. Brachioradials (forearm)

F. Hip Flexors (upper thigh)

G. Abductor (outer thigh)

H. Quadriceps (front of thigh)

I. Sartorius (front of thigh)

J. Tibialis Anterior (front of calf)

K. Soleus (front of calf)

L. Anterior Deltoid (shoulder)

M. Rectus Abdominus (stomach)

N. Adductor (inner thigh)

O. Trapezius (upper back)

P. Rhomboideus (upper back)

Q. Posterior Deltoid (shoulder)

R. Triceps (back of arm)

S. Latissimus Dorsi (mid back)

T. Spinae Erectors (lower back)

U. Gluteus Medius (hip)

V. Gluteus Maximus (buttocks)

W. Hamstring (back of leg)

X. Gastrocnemius (back of calf)

M6 Washer (78)

M8 Washer (72)

M10 x 45mm Bolt (65)

M6 x 140mm Screw (79)

M8 x 76mm Carriage Bolt (59)

M10 x 25mm Screw (58)

M4 x 40mm Screw (46)

M8 x 45mm Bolt (57)

M10 x 71mm Bolt (67)

M10 x 48mm Bolt (62)

M6 x 87mm Screw (68)

M8 x 89mm Bolt (64)

M8 x 115mm Bolt (76)

M6 x 25mm Screw (60)

M10 Nylon Locknut (73)

M10 Washer (71)

M8 Nylon Locknut (74)

M4 x 64mm Screw (81)

M4 x 16mm Screw (70)

M10 x 53mm Button Bolt (61)

M10 x 64mm Button Bolt (75)

M10 Split Washer (98)

M6 x 73mm Screw (103)

M4 x 5mm Screw (69)

M10 x 50mm Button Bolt (80)

M10 x 80mm Button Bolt (97)

M10 x 168mm Button Bolt (99)

PART IDENTIFICATION CHART

Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-

ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts

may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.

PART LIST—Model No. PFSY3415.0 R0805A

Key No. Qty. Description Key No. Qty. Description

11 Base

2 1 Base Plate

3 1 Upright

4 1 Top Frame

5 1 Rear Stabilizer

6 1 Seat Frame

7 1 Leg Lever

8 2 Press Arm

9 1 Squat Bar

10 2 Weight Guide

11 1 Weight Tube

12 1 Weight Tube Bumper

13 1 Shroud

14 1 Bottom Cover

15 1 Top Cover

16 2 Swivel Arm

17 12 Weight

18 1 Backrest

19 1 Seat

20 1 Pad Tube

21 4 Foam Pad

22 2 “V”-pulley

23 4 23/4" Pulley

24 5 3 1/2" Pulley

25 8 5mm Spacer

26 2 Half Finger Guard

27 4 Finger Guard

28 5 Cable Trap

29 4 Pulley Cover

30 1 Press Arm Cable

31 2 Extension Cable

32 2 Pulley Housing

33 2 Handle

34 2 Extension Strap

35 1 Squat Bar Pad

36 1Ankle Strap

37 6 Cable Clip

38 2 Base Cap

39 2 Pull-up Cap

40 419mm Round Inner Cap

41 251mm Round Inner Cap

42 1 110mm Round Inner Cap

43 2 Press Arm Cap

44 2 32mm Thick Round Inner Cap

45 1 51mm x 76mm Inner Cap

46 4 M4 x 40mm Screw

47 2 25mm Spacer

48 2 38mm Spacer

49 1 Bumper

50 2Weight Bumper

51 4 Swivel Arm Bushing

52 1 Lock

53 1 Lock Pin

54 1 Roll Pin

55 1 Weight Pin

56 2 25mm Round Inner Cap

57 3 M8 x 45mm Bolt

58 16 M10 x 25mm Screw

59 2 M8 x 76mm Carriage Bolt

60 6 M6 x 25mm Screw

61 2 M10 x 53mm Button Bolt

62 1 M10 x 48mm Bolt

63 1 51mm Thin Round Inner Cap

64 2 M8 x 89mm Bolt

65 4 M10 x 45mm Bolt

66 2 Eyehook

67 1 M10 x 71mm Bolt

68 1 M6 x 87mm Screw

69 2 M4 x 5mm Screw

70 8 M4 x 16mm Screw

71 17 M10 Washer

72 10 M8 Washer

73 17 M10 Nylon Locknut

74 11 M8 Nylon Locknut

75 2 M10 x 64mm Button Bolt

76 2 M8 x 115mm Bolt

77 2 M5 x 15mm Screw

78 8 M6 Washer

79 3 M6 x 140mm Screw

80 2 M10 x 50mm Button Bolt

81 2 M4 x 64mm Screw

82 1 VKR Frame

83 2 Arm Pad Base

84 2 Arm Pad

85 1 Curl Post

86 1 Curl Pad Base

87 1 Curl Pad

88 1 Backrest Base

89 1 Headrest Base

90 1 Headrest

91 1Seat Base

92 2 Large VKR Cap

93 2 Arm Pad Bushing

94 4 32mm Round Inner Cap

95 1VKR Bumper

96 2Pull-up Handle

97 4 M10 x 80mm Button Bolt

98 4 M10 Split Washer

99 1 M10 x 168mm Button Bolt

100 1 Curl Knob

101 1 VKR Pin

102 4 32mm Thin Round Inner Cap

103 4 M6 x 73mm Screw

104 1 Curl Bar

105 264mm Round Outer Cap

106 1 Squat Bar Hook

107 1 Chain

#1User’sManual

# 1 Exercise Guide

#1Hex Key

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.

105

40 21

67 6

103

78 78 93

103

8786

100

101

104

102

105

106

107

EXPLODED DRAWING A—Model No. PFSY3415.0 R0805A

7247

54 26

25 25

869

14 70

71 71

24 28

32 71

24 28 65

102

71 98

EXPLODED DRAWING B—Model No. PFSY3415.0 R0805A

LIMITED WARRANTY

ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-

rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This

warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing

or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which

warranty claims are made must be pre-authorized by ICON. If the product is shipped to a service center,freight

charges to and from the service center will be the customer’s responsibility. For in-home service, the customer

will be responsible for a minimal trip charge. This warranty does not extend to any product or damage to a

product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs

not provided by an ICON authorized service center; products used for commercial or rental purposes; or prod-

ucts used as store display models. No other warranty beyond that specifically set forth above is authorized by

ICON.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection

with the use or performance of the product or damages with respect to any economic loss, loss of property,

loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential

damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse-

quential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-

chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.

Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation

may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give

the following information

1. the MODEL NUMBER of the product (PFSY3415.0)

2. the NAME of the product (PROFORM FUSION 4.0 LX weight system)

3. the SERIAL NUMBER of the product (see the front cover of this manual)

4. the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the

center of this manual)

ORDERING REPLACEMENT PARTS

Proform Pfsy34150 Fusion 4 0 Lx Weight System Users Manual WESY39240 212817

Proform-Pfsy34150-Owner-S-Manual proform-pfsy34150-owner-s-manual

PFSY3415.0 to the manual d3aea54b-b51e-41fe-a89e-c03defb50b94

Navigation menu

Versions of this User Manual:

Views

Navigation