Psion 7535G2RA2041 802.11g Compact Flash Module User Manual netpad Win CE Quick Start Guide
Psion Inc 802.11g Compact Flash Module netpad Win CE Quick Start Guide
UserManual.wiki
>
Psion
>
7535G2RA2041 User Manual
Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 251.4.2 Installing The Battery•Slide the charged battery with the contoured plastic facing you into the 7535 G2. • Click the battery into place.1.4.3 Battery Swap And RuntimeThe 7535 G2 battery will operate for ten hours under typical operat-ing conditions after a full charge. Typical battery life is 300 charge cycles or 2 years average use. A full charge is completed in 4 hours with a typical charge time of 1.5 hours.1.5 Switching The 7535 G2 On• Press and hold down [ENTER] for at least one second. • When all four LEDs flash yellow, release the [ENTER] key.A splash screen displaying the Psion Teklogix logo and the Win-dows CE logo appears followed by the startup desktop.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-31.png)
![26 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start GuideNote: If the 7535 G2 is in suspend state, pressing [ENTER] ‘wakes’ the unit from this state. The screen in which you were working before the computer entered suspend state is displayed.1.6 Switching The 7535 G2 OffImportant: Keep in mind that turning off the 7535 G2 does not result in a complete reboot; rather, the unit enters a power-saving, “suspend” state. When the hand-held is turned on from suspend state, operation resumes within a few seconds. To switch off the 7535 G2:• Press the [BLUE] key, and then press the [ENTER] key.Important: If the word ‘BLUE’ is displayed in uppercase in the taskbar area at the bottom of the screen, this key is locked “on”—the 7535 G2 will not switch off. Press the [BLUE] key again to unlock it; then press [BLUE] [ENTER] to switch the 7535 G2 off.If the ‘BLUE’ option is enabled in the ‘One Shots’ dialog box (accessible through the ‘Keyboard’ Control Panel icon) the 7535 G2 can be turned off when the [BLUE] key is locked on.1.7 Connecting To An 802.11 NetworkIn most cases, the 7535 G2 must be configured before it can connect to an 802.11 wireless network. Chapter 2, Section 2.2.2, “Configur-ing An IEEE 802.11 Radio Installed In The 7535 G2” in the 7535 G2 Hand-Held Computer User Manual (PN 8000075) describes this configuration process. Once the 7535 G2 is properly](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-32.png)
![28 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide2.2 The KeyboardNote: Refer to “Navigating Using The Keyboard” on page 47 for details about using keys to move around Windows CE.The 7535 G2 offers two types of keyboard layouts—a 58-key key-board and a 36-key, large button keyboard. The [BLUE] and [ORANGE] modifier keys provide access to addi-tional keys and system functions. These functions are colour coded in orange and blue print above the keyboard keys.2.2.1 Modifier KeysThe [SHIFT], [CTRL], [ALT], [BLUE] and [ORANGE] keys are modifier keys. Pressing a modifier key changes the function of the next key pressed. For example, on a 58-key keyboard, a square bracket is printed in orange print above the [4] key. Pressing the Stylus(Pointing Tool)Battery PackTether PortScanner Window](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-34.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 29[ORANGE] key followed by the [4] key displays a square bracket rather than the number 4. The [SHIFT], [CTRL] and [ALT] keys operate much like a desktop keyboard except that they are not chorded (two keys held down simultaneously). The modifier key must be pressed first followed by the key whose function you want modified.Activating Modifier KeysWhen a modifier key is pressed once, it is displayed in lowercase let-ters in the taskbar at the bottom of the 7535 G2 screen. For example, if the [CTRL] key is pressed, ctrl key is displayed at the bottom of the unit screen. Once the next key is pressed, the modifier key becomes inactive and disappears from the taskbar.Locking Modifier KeysWhen a modifier key is pressed twice, it is ‘locked’ on. A ‘locked’ modifier key is displayed in uppercase letters in the taskbar. For example, pressing the [BLUE] key twice locks it on—it is displayed as BLUE KEY in the taskbar at the bottom of the computer screen.The locked modifier key will remain active until it is pressed a third time to unlock or turn it off.2.2.2 The KeysThe [SHIFT] KeyUsed to display uppercase alpha characters and provide access to the symbols above the numeric keys.The Arrow KeysMove the cursor around the screen in the direction of the arrow—up, down, left and right.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-35.png)
![30 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start GuideThe [BKSP/DEL] KeyMoves the cursor one character to the left, erasing the incorrectly-entered key stroke. [DEL] key ([BLUE] [BKSP]) erases the character at the cursor position.The [CTRL] And [ALT] KeyModify the function of the next key pressed and are application-dependent.The [TAB] KeyUsually moves the cursor to the next field to the right or downward.The [ESC] KeyGenerally used as a keyboard shortcut to close the current menu, dialog box or activity and return to the previous one.The [SPACE] KeyInserts a blank space between characters. In a Windows dialog box, the [SPACE] key enables or disables a checkbox.The [SCAN] KeyActivates the scanner beam while pressed. For units without internal scanners, pressing this key has no affect.2.2.3 The 58-Key KeyboardIn addition to alphanumeric keys that are directly accessible on the keyboard (no key combination is required) and the keys described in this chapter, the 58-key keyboard also provides function keys and macro keys. They can be custom-defined for each application.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-36.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 312.2.4 The 36-Key KeyboardOn 36-key 7535 G2s, all alpha characters are printed on the unit plastic in orange typeface above the numeric keys. An indicator in the left corner of the taskbar displays the currently selected charac-ter. To access an alpha character, first press the [ORANGE] key and then press the numeric key above which the alpha character you want to type is printed. Choosing A Single Alpha CharacterNote: The following examples assume that the [ORANGE] key is enabled as ‘Lock’ mode in the ‘One Shot’ screen (accessible through the Control Panel ‘Keyboard’ icon). In ‘Lock’ mode, pressing the [ORANGE] key once locks it ‘on’.The examples below illustrate how to access A, B and C, all of which are printed in orange characters above the numeric key, [2].To choose the letter ‘a’:• Press the [ORANGE] key, and press the numeric key [2].• Press the [ORANGE] key again to unlock or turn it off.To choose the letter ‘b’:• Press the [ORANGE] key, and press [2] twice.• Press the [ORANGE] key again to unlock or turn it off.To choose the letter ‘c’:• Press the [ORANGE] key, and press [2] three times. • Press the [ORANGE] key again to unlock or turn it off.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-37.png)
![32 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start GuideCreating Uppercase LettersTo display a capital letter:• Press the [ORANGE] key and then the [SHIFT] key before typing the alpha character.Note: If you want to use uppercase characters at all times, press [BLUE] [SHIFT]. An icon of an uppercase ‘A’ is displayed in the taskbar indicating that all letters will be displayed as uppercase characters.Choosing Multiple Characters From The Same KeyIf you need to choose more than one alpha character from a single key, you’ll need to press the ‘Accept’ key between alpha selections. The ‘Accept’ key is presented as an arrow ⇒ symbol above the ‘0’ (zero) key. For example, suppose you want to type the letters ‘a’, ‘b’ and ‘c’. These letters are all accessible from the numeric key, [2].To type the letter ‘a’:• Press the [ORANGE] key, and then press the numeric key, [2].• Press the ‘Accept’ key [⇒] (zero key) to indicate that the let-ter ‘a’ should be accepted and that another letter from the same key will be chosen.To type the letter ‘b’:• Press the [2] key twice, and press [⇒] to accept the letter ‘b’.To type the letter ‘c’:• Press the [2] key three times.When you have completed your alpha selections from this key, you can do one of the following:](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-38.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 33• If you want to choose additional alpha characters from another key(s), leave the [ORANGE] key ‘on’, and press the numeric key with the alpha character you require, or • If you do not want to choose any additional alpha characters, press [ORANGE] again to unlock or turn ‘off’ the key and end alpha selection.Choosing Multiple Characters From A Range Of KeysIf you plan on choosing alpha characters from a number of different keys, you are not required to press the ‘Accept’ [⇒] key after each alpha selection. The [⇒] key is only required when you are choosing more than one alpha character from the same key—e.g., ‘a’, ‘b’ and ‘c’ from the [2] key. Suppose you want to type the letters ‘a’, ‘d’ and ‘g’. These alpha characters are accessed from the numeric keys [2], [3] and [4].• With the [ORANGE] key locked ‘on’, press [2] to type the letter ‘a’.• Press [3] to type ‘d’, and press [4] to type the letter ‘g’.• To end alpha selection, press the [ORANGE] key again to unlock it.2.2.5 Adjusting The Keypad BacklightTo adjust the intensity of the keypad backlight and the conditions under which this backlight is activated.•In the Control Panel, choose the Keyboard icon.Note: Access may be restricted to supervisory use.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-39.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 352.3.2 Adjusting The ContrastThe display contrast can be adjusted from the unit keyboard using the [BLUE] key and function keys [F1] and [F2].• Press the [BLUE] key twice to lock it on, and then press [F1] to darken or [F2] to lighten the display.• When you’re satisfied with the contrast adjustment, press [BLUE] again.Sets the duration of time that the backlight stays on at half the configured intensity when the unit is not in use.Determines how dark the ambient lightlight needs to be before the backlightswitches on.Sets the duration of time that the backlight stays on at the configured intensity whenthe unit is not in use.Adjusts the light intensity of the backlight.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-41.png)
![36 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide2.3.3 Calibrating The TouchscreenNote: This function may be restricted to supervisory use.If your 7535 G2 touchscreen has never been calibrated or if you find that the stylus pointer is not accurate when you tap on an item:•In the Control Panel, choose the Stylus icon, and select the Calibration tab, and then choose the [Recalibrate] button.• Follow the onscreen directions to calibrate the display.2.4 7535 G2 Indicators7535 G2s use LEDs (Light Emitting Diodes), onscreen messages and audio tones as indicators.2.4.1 LEDsThe 7535 G2 is equipped with four tri-coloured LEDs. This section outlines what these LEDs indicate.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-42.png)
![40 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start GuideStart Menu options may be very limited depending on the security setting assigned to the computer.Modifier Key Indicators[SHIFT], [CTRL], [ALT], [BLUE] and [ORANGE] are modifier keys that have onscreen indicators to show when a key is active or locked. If a modifier key is pressed once to activate it, the key is dis-played in the taskbar in lowercase characters. If a modifier key is pressed twice, it is ‘locked on’ and the onscreen indicator is dis-played in uppercase letters in the taskbar.Battery GaugeThe battery-shaped icon displayed in the taskbar provides a visual indication of the remaining battery power. When the battery level is low—approximately 15 minutes from empty—a warning window pops up. When the battery power is completely depleted, a final warning window indicates that the 7535 G2 will be powered down.If the 7535 G2 is using external AC power, an AC icon is displayed.Full 75% 50% 25% Empty AC Connection](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-46.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 432.4.3 Audio IndicatorsThe 7535 G2 beeper provides a variety of sounds and can be config-ured to emit a sound under a variety of conditions. Refer to ‘Volume Adjustment’ in Chapter 5 of the ‘7535 G2 Hand-Held Computer User Manual’ for details about determining when your unit will beep.Adjusting The Beeper VolumeThe volume function keys located along the top of the keyboard are used to adjust the beeper volume emitted from your 7535 G2.The increase volume function key is labelled with a plus sign and the decrease volume function key is labelled with a minus sign .To adjust the beeper volume:• Press the [BLUE] key twice to lock it ‘on’.• Press the increase volume function key or the decrease volume function key until the volume meets your needs.• Press the [BLUE] key again to ‘unlock’ it.2.5 Monitoring The Network ConnectionIf your hand-held is equipped with a wireless LAN radio, it will typically associate with the nearest access point. The radio signal quality meter in the taskbar indicates the relative strength of the communication link. To access the radio signal icon from the keyboard:• Press [BLUE] [0]. Choose Shortcuts>System Tray from the Start Menu.• Use the arrow keys to highlight the radio signal icon in the taskbar.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-49.png)
![44 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide•Press [ENTER] to display the radio quality dialog box.If you’re using a touchscreen:• Tap on the radio icon in the taskbar to display the radio qual-ity dialog box.Note: Moving in and out of the radio coverage area can have vary-ing effects on a network session. At times, you may need to renew your connection by logging in again.2.6 Checking The ScannerIf your 7535 G2 is equipped with an internal scanner, you can test it to ensure that it is operating properly. Point the scanner window at a bar code that your scanner was designed to decode – for example, a 1D UPC bar code or 2D bar code. Press the SCAN button or the pis-tol trigger, and check for a valid decode on the hand-held screen.“Scanning Techniques” on page 44 provides some pointers to help ensure successful decodes. “Scan LED Indicators” also on page 45 describes how to determine a successful decode.2.6.1 Scanning TechniquesNote: The scanning techniques described here apply to internal and external scanners.• Hold the scanner at an angle. Do not hold it perpendicular to the bar code.•Do not hold the scanner directly over the bar code. In this position, light can reflect back into the scanner’s exit window and prevent a successful decode.• Scan the entire bar code. If you are using a 1D or 2D scanner, make certain that the scan beam crosses every bar and space on the bar code, including the margins on either end of the symbol.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-50.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 473.2 Navigating Using The KeyboardNote: Refer to “The Keyboard” on page 28 for more detail about the keyboard keys.If your 7535 G2 has a standard screen (rather than a touchscreen), choosing icons and navigating dialog boxes, displaying the desktop, and so on requires keyboard input. Keep in mind that unlike a desktop computer, the 7535 G2 does not support key chording (pressing two keys at the same time). You must press one key followed by the next in sequence.Operation Key or Key CombinationSwitch between applications [ALT] [TAB]Open the task manager screen [ALT] [ESC]Move the cursor Arrow keysOpen file, folder or icon [ENTER]Exit & Save [ENTER]Close/Exit & Do Not Save [ESC]Navigate Dialog Boxes [TAB]To move cursor up: [SHIFT][TAB]To display the next ‘tab’ in a dialog box: [CTRL][TAB]Select Radio Button/Press Button[SPACE]Go to Start Menu [BLUE][0]](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-53.png)
![48 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide3.3 The Startup DesktopWhen the 7535 G2 boots up, the startup desktop is displayed. Any applications stored in the Startup folder will start up immediately. The Startup folder is located in \Windows\Startup and \Flash Disk\Startup.3.3.1 Accessing Desktop Icons• Use the arrow keys to highlight the icon, and press [ENTER] to launch the highlighted icon.Note: If the arrow keys do not highlight the desktop icons, the desk-top may not be selected. Press [BLUE] 0 (zero) to display the Start Menu, and choose Desktop. Now the desktop will be “in focus” and the arrow keys will highlight the icons.If you’re using a touchscreen:• Tap the icon to select it, or double-tap on it to open a window or, in the case of an application icon, launch an application.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-54.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 493.3.2 The TaskbarThe 7535 G2 is equipped with a taskbar at the bottom of the screen. It displays icons through which you can view the security level,battery capacity and radio signal quality of your unit. A 7535 G2 attached to a charger, cradle, docking station or PDM displays the associated icon.The taskbar also displays active modifier keys—[SHIFT], [ALT], [CTRL], [BLUE] and [ORANGE]. Keys that have been locked “on” are displayed in uppercase letters. Using The Taskbar• Press [BLUE] [0] to display the Start Menu.• Press the [DOWN] arrow key to highlight the Shortcut menu. Press the [RIGHT] arrow key to display the sub-menu. Type [Y] to choose System Tray from the menu. • Press the [LEFT] and [RIGHT] arrow keys to highlight the icon in the taskbar about which you’d like more information.A tooltip is displayed as each taskbar icon is highlighted. The tooltip provides the status of each icon.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-55.png)
![50 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide• Press [ENTER] to display the associated dialog box.If you’re using touchscreen:• Tap and hold the stylus on an icon to display the icon's tooltip. Double-tap the icon to open the Control Panel dialog box associated with the icon.3.4 The Start MenuThe Start Menu lists operations you can access and work with. It is available from the startup desktop or from within any application.To display the menu:• Press [BLUE] [0] (zero).• Use the arrow keys to highlight a menu item, and press [ENTER], or If the menu item has an underlined character:• Type the underlined alpha character—for example, to display Security, type the letter s.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-56.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 51If you’re using a touchscreen:• Tap on the Start button in the taskbar. Tap on the item in the menu with which you want to work.The DesktopChoosing Desktop from the Start Menu displays the 7535 G2desktop. Security SettingsTo assign a security level:• Choose Security from the Start Menu.• Choose a security level from the dialog box. To allow access to all the Start Menu and taskbar options, choose the Supervi-sor security level. • Type the appropriate password in the Password: text box, and press [ENTER].To change the password:Note: Keep in mind that this is the same password as that assigned through the Password control panel applet.• Choose a security level, and enter the existing password in the Password field.• Choose the [Set Password] button.In the Password Properties dialog box:• Type the new password in the Password: text box, and retype the new password in the Confirm Password: text box.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-57.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 53The System TrayThe System Tray option allows access to the icons in the taskbar at the bottom of the screen. The taskbar displays indicators such as a battery capacity gauge and the security level. These indicators are attached to dialog boxes that provide additional information. • Choose System Tray from the Start Menu.When System Tray is chosen, the taskbar icons become accessible. To display the dialog box attached to an icon:• Use the [LEFT] and [RIGHT] arrow keys to highlight an icon—for example, the security icon.• Press [ENTER] to display the security level dialog box.If you’re using a touchscreen, you don’t need to use System Tray: You have direct access to the icons in the taskbar.• Tap on the icon with which you want to work. The associated dialog box is displayed.Cycle TasksWhen Cycle Tasks is selected (and the Task Manager is not open), you can cycle through active applications. • Press [BLUE] [0] (zero) [T] [C] to cycle to the next active task, orPress [ALT][TAB].The Task ManagerThe Task Manager option allows you to switch to another task or to end an active task. To display the task manager window:• Press [BLUE] [0] (zero) [T] [T], or](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-59.png)
![54 Psion Teklogix 7535 G2 Hand-Held Computer Quick Start GuidePress [ALT][ESC].SettingsThe Settings menu provides access to the Control Panel applets, lets you configure your radio (Network and Dial-up Connections) and customize the Taskbar and Start Menu.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-60.png)
![Psion Teklogix 7535 G2 Hand-Held Computer Quick Start Guide 57Dialog boxes contain one or more of the following elements:Tab: A tab separates different elements of a dialog box. Press the [TAB] key until a tab in the dialog box is highlighted. To display adjoining tabs, press the [RIGHT] or [LEFT] arrow key. To display the information in the next tab from anywhere in the win-dow, press [CTRL] [TAB].Textbox: A textbox requires that you type information. Press the [TAB] key to highlight the textbox and then type the appropriate information.Dropdown: This type of menu is identified by up and down arrows next to the dropdown menu to indicate that additional options are available. Press the [TAB] key to highlight the menu, and use the arrow keys on your keyboard to cycle through the options. Checkbox: This box allows you to select or deselect an option. To select or deselect a checkbox, press the [TAB] key to highlight the checkbox, and press the [SPACE] key to select or deselect it.Radio buttons: These buttons allow you to choose from a number of options. For example, in the sample screen under section 3.5 on page 56, you can choose to ‘Obtain an IP address via DHCP’ or ‘Specify an IP address’. Press the [TAB] key to highlight a radio button option, and then select a radio button by pressing the arrow keys to highlight the appropriate option.Buttons: This type of button allows you to ‘Save’, ‘Delete’ and so on the options you’ve chosen in a dialog box. Use the [TAB] key to highlight the button you want to use. Press the [ENTER] key to activate it.Saving Your Choices: Once you’ve made all your changes, press the [ENTER] key to save your changes and exit the window.Note: A dialog box item that is displayed in grey text indicates that it is not currently available.](https://usermanual.wiki/Psion/7535G2RA2041/User-Guide-716899-Page-63.png)
