Psion AIR200X RFID MODULE LF-AIR200-G2-XMOD User Manual USERS MANUAL

Psion Inc RFID MODULE LF-AIR200-G2-XMOD USERS MANUAL

USERS MANUAL

October 23, 2007 DPD A00332 A00 Sheet 1 of 7 WORKABOUT PRO RFID MODULE LF-AIR200-G2-XMOD EXPANSION MODULE INSTRUCTIONS Important: All Approval and safety information is outlined in the ‘Workabout pro G2 Handheld-computer User Manual’ – part number 8100140A. This manual is available on our website www.psionteklogix.com through the Teknet extranet Installation of the RFID Module LF-AIR200-G2-XMOD: Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to meet your specific mobile computing requirements. This chapter outlines how to install the RFID Module LF-AIR200-G2-XMOD and the external RFID Antenna LF-AEA120-G2. Before installing a module in the WORKABOUT PRO G2, all power sources must be turned off. • Remove the batteries. If your unit is using AC power, disconnect it. • Slide the switch to position OFF to shut off internal battery power. With the power shut down, you can install the RFID Module LF-AIR200-G2-XMOD. • Remove and discard the two screws on the bottom of the metal frame. • Put the adapter board in the same alignment of the expansion connector on the WORKABOUT PRO. Apply slight pressure to snap the module into place on the hand-held.
October 23, 2007 DPD A00332 A00 Sheet 2 of 7 • Use four screws provided to secure the module in place. • Stick the RFID Module LF-AIR200-G2-XMOD to the WORKABOUT PRO, as shown. • Fix it with the 2 added washers and screws. • Fix the four screws on the top of the end cap.
October 23, 2007 DPD A00332 A00 Sheet 3 of 7 • Slide the switch to the position ON to turn power back on. • Replace the back plate and batteries. For detailed instructions, pleased refer to the WORKABOUT PRO Hand-Held Computer User Manual. These manuals are available on our website www.psionteklogix.com through the Teknet extranet Installation of the external RFID Antenna LF-AEA120-G2: • The RFID Antenna LF-AEA120-G2 can easily be fixed to the reader by a so called Binder plug. • Hook the mounting plate of the AEA120 into the bottom of the Workabout PRO. Fit both together, so that the screw holes match. • Bolt the AEA120 to the Workabout. • Screw the silver cap off from the socket.
October 23, 2007 DPD A00332 A00 Sheet 4 of 7 • Put the Binder plug of the telescope antenna in the socket of the RFID Module LF-AIR200-G2-XMOD. • Pay attention to the groove. • Follow the instructions of your Workabout PRO, to start a read. READING AREA: This area depend of the TAG type, TAG packaging, configuration of the WORKABOUT PRO (scanner, Compact flash…), environment (metallic or not). TAG Reading Area Reading Area
October 23, 2007 DPD A00332 A00 Sheet 5 of 7 WORKABOUT PRO RFID MODULE LF-AIR200-G2-XMOD RFID Regulatory Information
October 23, 2007 DPD A00332 A00 Sheet 6 of 7
October 23, 2007 DPD A00332 A00 Sheet 7 of 7 IMPORTANT NOTE FOR NORTH AMERICA: The RFID must not be used whilst the host WORKABOUT PRO is being powered by the ac/dc adaptor. FCC Information to Users: This product and it antennas must not be co-located or operated in conjunction with any other antenna or transmitter. Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued compliance, the product must not be held closer than 20 cm from the rest of the body. Federal Communication Commission Interference Statement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Emissions Information for Canada: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device has been designed to operate with the antennas listed below, and having a maximum gain of 1.8 dB. Antennas not included in this list or having a gain greater than 1.8 dB are strictly prohibited for use with this device. The required antenna impedance is 2.8 ohms. - RFID Antenna LF-AEA120-G2

Navigation menu