Psion HFT2G2X RFID MODULE HF-T2-G2-SMOD User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	846749
Application ID	OIUjQto2BlO2puPTNXJoBg==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.24kB (253042 bits)
Date Submitted	2007-09-24 00:00:00
Date Available	2007-09-25 00:00:00
Creation Date	2007-09-13 21:03:42
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2007-09-13 21:03:42
Document Title	Microsoft Word - RFID Module HF-T2-G2-Xmod UserMan.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	heyer

WORKABOUT PRO RFID MODULE HF-T2-G2-XMOD
EXPANSION MODULE INSTRUCTIONS
Important: All Approval and safety information is outlined in the ‘Workabout pro G2
Handheld-computer User Manual’ – part number 8100140A. This manual is available on
our website www.psionteklogix.com through the Teknet extranet
Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to
meet your specific mobile computing requirements. This chapter outlines how to install the RFID Module
HF-T2-G2-XMOD (this module is composed of one RFID Coupler HF-T2-G2-XMOD and one RFID
Antenna HF-A1-G2-XMOD).
Before installing a module in the WORKABOUT PRO G2, all power sources must be turned off.
•
Remove the batteries. If your unit is using AC power, disconnect it.
•
Slide the switch to position OFF to shut off internal battery power.
With the power shut down, you can install the RFID Module HF-T2-G2-XMOD.
•
Remove and discard the two screws on the bottom of the metal frame.
•
Put the RFID Coupler HF-T2-G2-XMOD in the same alignment of the expansion connector on the
WORKABOUT PRO. Apply slight pressure to snap the module into place on the hand-held.
August 29, 2007
DPD A00301 A10 Sheet 1 of 5
•
•
Use four new screws (M2 x 6 mm) provided to secure the module in place.
Remove and discard the two screws on the top of the metal frame.
•
Slide the RFID Antenna HF-A1-G2-XMOD under the metal frame (with the spiral pattern facing
up).
•
Connect the RFID Antenna HF-A1-G2-XMOD to the RFID Coupler HF-T2-G2-XMOD.
•
Use two new screws (M2 x 12mm) provided to secure the antenna on the metal frame.
•
Slide the switch to the position ON to turn power back on.
•
Replace the end-cap, back plate and batteries.
For detailed instructions, pleased refer to the WORKABOUT PRO Hand-Held Computer User Manual and
to the RFID MODULE HF-T2-G2-XMOD User manual. These manuals are available on our website
www.psionteklogix.com through the Teknet extranet
READING AREA:
This area depend of the TAG type, TAG packaging, configuration of the WORKABOUT PRO (scanner,
Compact flash…), environment (metallic or not).
Reading Area
TAG
August 29, 2007
DPD A00301 A10 Sheet 2 of 5
WORKABOUT PRO RFID MODULE HF-T2-G2-XMOD
RFID Regulatory Information
August 29, 2007
DPD A00301 A10 Sheet 3 of 5
August 29, 2007
DPD A00301 A10 Sheet 4 of 5
IMPORTANT NOTE FOR NORTH AMERICA:
The RFID must not be used whilst the host WORKABOUT PRO is being powered by the ac/dc adaptor.
FCC Information to Users:
This product and it antennas must not be co-located or operated in conjunction with any other antenna or
transmitter.
Radiation Exposure Compliance
This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued
compliance, the product must not be held closer than 20 cm from the rest of the body.
Federal Communication Commission Interference Statement.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
Emissions Information for Canada:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
August 29, 2007
DPD A00301 A10 Sheet 5 of 5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : Microsoft Word - RFID Module HF-T2-G2-Xmod UserMan.doc
Creator                         : heyer
Create Date                     : 2007:09:13 21:03:42+02:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2007:09:13 21:03:42+02:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:623d6386-577d-4216-ae37-c2e3dfd68719
Instance ID                     : uuid:7354b221-58b3-488a-a9be-3dc9c7b436cd
Page Count                      : 5
Author                          : heyer

EXIF Metadata provided by EXIF.tools