Public Wireless CM-100 Cable Modem 100 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	972515
Application ID	dmvnLq62T+nTe8hbi8UX5g==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.5kB (93785 bits)
Date Submitted	2008-07-17 00:00:00
Date Available	2008-07-17 00:00:00
Creation Date	2008-07-09 16:24:35
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-07-09 16:24:35
Document Title	Microsoft Word - PRELIM_Installation Guide CM-100__REV_B.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	DW8

Public Wireless
CM-100
User / Installation
Guide
Revision: PRELIM_DW_01
Date: 20 May 2008
FCC Compliance:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
Antenna Care/Unauthorized Modifications:
Use only the supplied antenna. Use of any other antenna other than the
one supplied with this unit could damage the unit and may violate FCC
regulations. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority
to operate the equipment.
The installation of a CM-100 has 3 main steps: 1) configuration of the CM-100 before is goes to the
installation site, 2) the installation at the location and 3) the verification the unit is working.
INSERT PIC HERE
IP BTS CONFIGURATION PROCEDURE USING A ROUTER
Important: turn wireless card off in your Personal computer before starting BSC Installer. ( Turn
router and radio on after starting the Installer.
1. Parts needed to program a radio
i. POE source to power radio
ii. Router
iii. 3 Ethernet cables 36 inches long
iv. BTS Installer software
v. Computer
2.
3.
4.
5.
6.
7.
8.
1.
2.
9.
Start BCS Installer
Add Mac ID of radio under New
FIND AND SELECT
ACTION – SET/GET ATTRIBUTES – CLOSE
UNIT ID – UNCHECK “RESET BTS AFTER SETTING”
ATTRIBUTES 1 – ENABLE – CONFIG FLAGS – F1, F7, F9, F11
ATTRIBUTES 2 – CONFIG PRIMARY OML LIST
NUMBER OF ADDRESSES IN LIST = 1
PRIMARY OMC IP ADDRESS = DEPENDING ON BSC BEING USED
DOWNLOAD – ENABLE DOWNLOAD – “BROWSE” – USE NEWEST
VERSION. THEN “OK”
10. CONFIGURE UNIT ID
11. SET/GET NV ATTRIBUTES – “OK”
12. DOWNLOAD SOFTWARE – IP BTS WILL BLINK
13. Select listen
14. Set Freq. to PCS1900 ( default is 1800)
15. FREQ SYNC – PCS1900 –RUN TEST 5 TIMES
ARFCN LISTS – APPLY WHITE LIST – SET ALL
APPLY FREQ SYNC OPTIONS AND ADJUST CLOCK – “OK”
16. CONNECT- WHEN GREEN – START TEST – SINGLE DIGIT TO PASS
17. PRINT SCREEN/PASTE SCREEN SHOT OF PASSING TEST
Installation of the CM-100 on the messenger cable
1. Parts needed for the installation
a. Programmed CM-100 that has a Picocell which has been preconfigured with it OML
Address and a Lantronix XPRESSDR+ which has been pre-configured with the latest
firmware revision and is configured for DHCP.
b. (Adjustable) Strand antenna mounting bracket.
c. Antenna.
d. LMR-400 Coax of the proper length for the distance between CM-100 and antenna
mounting locations.
e. (50 Ohm) Cable TV coax of the proper length from the CM-100 to Cable junction box
with connectors.
f. Tools needed ½ inch box wrench and 7/16 inch box wrench.
g. Antenna Bracket leveling tool.
2. Installing CM-100 on Messenger Cable wire
a. Loosen the ½ inch clamps in the center of the CM-100 case.
b. Loosen the cable coax so that the cable can be moved to allow the CM-100 clamps to be
attached to the messenger cable.
c. Hook the CM-100 clamps onto the messenger cable and tighten the clamps with the ½
inch wrench.
INSERT PIC HERE
3. Installing the antenna mounting bracket
a. Hook the bracket on the Messenger cable.
b. Using the antenna leveling tool, level the bracket in the perpendicular plane from the
messenger cable and tighten the ½ inch bolt.
c. Using the antenna leveling tool, now level the bracket in the parallel direction to the
messenger cable.
d. Install the antenna and connect the antenna coax to the antenna and the end connector
on the CM-100.
e. Install the cable coax to the cable splice and to the CM-100.
Testing
a. Call the Network Operation Center ( 800-XXX-XXXX) and report the serial number of
the unit.
b. The NOC will inform the installer the unit is working or not.
c. If not working follow the trouble procedures as directed by the NOC.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:07:09 16:24:35-07:00
Create Date                     : 2008:07:09 16:24:35-07:00
Format                          : application/pdf
Title                           : Microsoft Word - PRELIM_Installation Guide CM-100__REV_B.doc
Creator                         : DW8
Document ID                     : uuid:b39776d2-2afd-4c43-a4ea-803deb562cf1
Instance ID                     : uuid:4f195f59-c434-4371-891e-b1cca633b483
Page Count                      : 4
Author                          : DW8

EXIF Metadata provided by EXIF.tools