10266 2 B&G 102210 Install Manual P81748 (11/07) User
10266 2 B&G 102210 Install Manual 10266_2_B&G 102210 Install Manual
User Manual: Pump 10266 2 B&G 102210- Install Manual
Open the PDF directly: View PDF .
Page Count: 4
![](asset-1.png)
DESCRIPTION
Bell & Gossett Booster Pumps feature oil lubricated sleeve
bearings, a carbon/ceramic seal and a noise dampening spring
coupler. Bell & Gossett Booster Pump motors are designed
specifically for quiet operation and are built with thermal pro-
tection and drip-proof construction. The motor is non-
over-loading at any point on the pump curve.
This pump is nonsubmersible, for indoor use only.
PUMP APPLICATION
Bell & Gossett Pumps may be used for water circulating appli-
cations in hydronic, solar and chilled water systems. Bell &
Gossett recommends that bronze constructed pumps be used
for pumping potable water. For other applications contact your
local Bell & Gossett Representative. Note that some local
codes require using a check valve in the supply line when recir-
culating potable water.
It has not been investigated, nor is it intended for use in swim-
ming pool and marine areas.
OPERATIONAL LIMITS
These pumps are designed to pump liquids compatible with
their iron or bronze body construction. Unless special provi-
sions have been made by ITT Bell & Gossett, the operational
limits for Series 100, HV, PR and 2" Pumps are listed below.
Do not exceed these values.
Maximum Working Pressure: 125 psi
Maximum Operating Temperature: 225ºF
Electrical Rating: 115V, 60 Hz, 1PH
Motors with special electrical characteristics are available on
request. Contact your local Bell & Gossett Representative for
details.
SAFETY
INSTRUCTIONS
This safety alert symbol will be used in this manual and on the
pump instructions decal to draw attention to safety related
instructions. When used, the safety alert symbol means
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
FAILURE TO FOLLOW THE INSTRUCTIONS MAY RESULT IN
A SAFETY HAZARD.
Your Booster Pump should have these warning labels affixed
near the conduit box cover. If these warnings are missing or
illegible, contact your local Bell & Gossett Representative for
replacement labels.
Iron & Bronze Booster Pumps
INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER’S USE.
Series 100
Series HV
Series PR Series 2"
WARNING
BEFORE INSTALLING, USING OR
SERVICING THIS PRODUCT,
READ THE WARNING NOTES
AND INSTRUCTIONS IN
INSTRUCTION MANUAL.
FAILURE TO DO SO MAY
RESULT IN SERIOUS INJURY
OR PROPERTY DAMAGE
V56845
WARNING
RISK OF ELECTRIC SHOCK;
THIS PUMP HAS NOT
BEEN INVESTIGATED FOR
USE IN SWIMMING POOL
AND MARINE AREAS.
-NONSUBMERSIBLE PUMP-
P86313
INSTRUCTION MANUAL
P81748F
![](asset-2.png)
ELECTRICAL SAFETY
2
MECHANICAL SAFETY
WARNING: EXCESSIVE SYSTEM PRESSURE
HAZARD
The maximum working pressure of the pump is listed on
the nameplate – DO NOT EXCEED THIS PRESSURE.
Failure to follow these instructions could result in serious
personal injury, death and/or property damage.
WARNING: EXCESSIVE PRESSURE HAZARD –
VOLUMETRIC EXPANSION
The heating of water and other fluids causes volumetric
expansion. The associated forces may cause failure of sys-
tem components and release high temperature fluids. This
can be prevented by installing properly sized and located
expansion tanks and pressure relief valves. Failure to follow
these instructions could result in serious personal injury,
death and/or property damage.
WARNING: EXTREME TEMPERATURE HAZARD
If the pump, motor, or piping are operating at ex-
tremely high or low temperature, guarding or insulation is
required. Failure to follow these instructions could result in
serious personal injury, death and/or property damage.
THERMAL SAFETY
WARNING: ELECTRICAL GROUNDING HAZARD
Adequate electrical grounding is required for the safe
operation of B&G Pumps. The use of grounded metal con-
duit assures this requirement. If the means of connection to
the supply-connection box (wiring compartment) is other
than grounded metal conduit, ground the pump back to the
service by connecting a copper conductor at least the size
of the circuit conductors supplying the pump to the green
grounding screw provided within the wiring compartment.
Failure to follow these instructions could result in serious
personal injury, death and/or property damage.
WARNING: ELECTRICAL SHOCK HAZARD
Disconnect and lockout the power before servicing.
Failure to follow these instructions could result in serious
personal injury or death.
REMOVAL OF THE PUMP FROM EXISTING SYSTEM FOR REPLACEMENT
1. Close the valves on the suction and discharge sides of
the pump. If no valves have been installed, it may be nec-
essary to drain the system.
WARNING: HOT WATER HAZARD
Before draining the system, allow water to cool to
100°F max. open the drain valve (take precautions against
water damage) and leave the drain valve open until servicing
is complete. Failure to follow these instructions could result
in serious personal injury, death and/or property damage.
2. Loosen the conduit box cover screw and remove the cover.
3. Disconnect the electrical supply lines to the pump.
WARNING: HIGH PRESSURE HAZARD
Pressure may be present in the pump body. This
pressure can be relieved by loosening the flange bolts and
shifting the pump assembly slightly to allow the pressur-
ized water to escape. Failure to follow these instructions
could result in serious personal injury or death.
4. Remove the flange bolts and remove the pump from the
piping.
WARNING: ELECTRICAL SHOCK HAZARD
Electrical connections are to be made by a qualified
electrician in accordance with all applicable codes, ordi-
nances and good practices. Failure to follow these instruc-
tions could result in serious personal injury, death and/or
property damage.
SAFETY REQUIREMENTS
WARNING: HOT WATER HAZARD
When disassembling a gasket joint, always use a new
gasket upon reassembly. NEVER RE-USE OLD GASKETS.
Failure to follow these instructions could result in serious
personal injury, death and/or property damage.
WARNING: ELECTRICAL OVERLOAD HAZARD
Three phase motors must have properly sized heaters
to provide overload and under voltage protection. Single
phase motors have built-in overload protectors. Failure to
follow these instructions could result in serious personal
injury, death and/or property damage.
WARNING: ELECTRICAL SHOCK HAZARD
Be certain the electrical power is not present at the
motor leads before continuing. Failure to follow these in-
structions could result in serious personal injury or death.
WARNING: UNEXPECTED START-UP HAZARD
Single phase motors are equipped with automatic
reset overload protectors. The pump can restart without
warning. Disconnect and lockout power before servicing.
Failure to follow these instructions could result in serious
personal injury, death and/or property damage.
WARNING: RISK OF ELECTRIC SHOCK
Do not install this pump in swimming pool or marine
areas. Failure to follow these instructions could result in
serious personal injury, death and/or property damage.
![](asset-3.png)
MODE OF DISCHARGE
Bell & Gossett Pumps can be installed to discharge up, down,
left or right. The oiling ports must always be in the twelve
o’clock position (on top) with motor and bearing assembly in a
horizontal position. THE ARROW ON THE PUMP BODY MUST
POINT IN THE DIRECTION OF THE FLOW. If it becomes nec-
essary to change the mode of discharge, refer to B&G
Instruction Manual HS-105-SM for specific instructions in
removing the motor and bearing assembly from the pump
body.
NOTE: The position of the conduit box is determined by the
model of the motor used. The oiling ports must always be in
the up position.
3
WARNING: WATER LEAKAGE HAZARD
To prevent leakage, make certain that the flange
bolts have been adequately torqued. Failure to follow these
instructions could result in serious personal injury and/or
property damage.
PUMP LOCATION
Bell & Gossett Booster Pumps should be installed where there
will be sufficient room for future inspection, maintenance and
service. It is highly recommended that service valves (shut-off)
also be installed on each side of circulator pumps to facilitate
servicing or replacing the pump without draining the system.
IMPORTANT: In closed systems, do not install and operate
Bell & Gossett pumps, 3D valves, suction diffusers, etc., with-
out properly sized safety and control devices. Such devices
include the properly sized and located pressure relief valves,
expansion tanks and pressure, temperature, and flow con-
trols. If the system is not equipped with these devices, consult
the responsible engineer or architect before operating.
PUMP SUPPORTING AND PIPING
Install the suction and discharge flanges on the pipe ends
using Teflon®* tape sealer or high quality thread sealant.
Minimize strain on the pump by supporting the suction and
discharge piping with pipe hangers near the pump. Line up the
vertical and horizontal piping so that the bolt-holes in both the
pump and pipe flanges are aligned. DO NOT ATTEMPT TO
SPRING THE SUCTION OR DISCHARGE LINES INTO POSI-
TION. THIS MAY RESULT IN UNWANTED STRESS IN THE
PUMP BODY, FLANGE CONNECTIONS AND/OR PIPING. The
code for pressure piping, ANSI B31.1, lists types of supports
for various applications.
Ordinary wire or band hangers are not adequate to maintain
alignment. It is very important to provide strong, rigid support
for the suction and discharge lines.
IMPORTANT: Do not support the pump by its power pack. To
function properly, the motor power pack must not be strained.
PUMP FLANGES
New Bell & Gossett flanges gaskets must be installed between
the flanges of the pump body and suction and discharge
pipes. The gaskets should be clean and grease-free; old gas-
kets should never be reused.
Apply torque in even increments to both flange bolts until the
value listed in the table below is reached. Both the suction and
discharge flanges must be torqued in this manner.
PUMP INSTALLATION WARNING: HOT WATER HAZARD
When disassembling a gasketed joint, always use
a new gasket upon reassembly. NEVER RE-USE OLD
GASKETS. Failure to follow these instructions could result
in serious personal injury, death and/or property damage.
OIL PORTS
*Teflon®is a registered trademark of E.I. DuPont de Nemours and Company.
100 With
Full Face 100 With Ring
Pump Series Flange Gasket* Flange Gasket PR HV 2"
Bolt Torque 150-180 in. lbs. 96-132 in. lbs. 96-132 in. lbs. 96-132 in. lbs. 96-132 in. lbs.
12.5-15 ft. lbs. 8-11 ft. lbs. 8-11 ft. lbs. 8-11 ft. lbs. 8-11 ft. lbs.
Full turns of
the nut from 1-1/4 1 1 3/4 3/4
finger tight
* No longer used.
WARNING: HOT WATER HAZARD
Make sure that each flange gasket remains seated in
the flange groove during and after installation. Failure to fol-
low these instructions could result in serious personal
injury, death and/or property damage.
![](asset-4.png)
1. Keep the pump and motor properly lubricated.
2. If the system is to be exposed to freezing temperatures,
drain the pump.
PERIODIC INSPECTION
Inspect the pump regularly for leaking seals, worn gaskets,
and loose or damaged components. Replace or repair as
required.
Refer to the following manuals for additional repair instruc-
tions for Bell & Gossett Iron & Bronze Booster Pumps:
Coupler & Motor Mount Replacement . . . . . .#S15900, Rev. D
Booster Pump Service Manual . . . . . . . .#HS-105-SM, Rev. 3
SYSTEM PREPARATION1
Prior to pump start up, closed heating and cooling systems
should be flushed with clean water and drained. The system
should then be filled with clean water having a PH between 7
and 9.
LUBRICATION1
Although the new B&G pumps are test run at the factory, they
must be lubricated thoroughly before being placed in opera-
tion. Bell & Gossett supplies a high quality lubricant specifi-
cally for this purpose which can be purchased from any B&G
Representative (Part No. L23401). Proper lubrication proce-
durs are as follows:
1. PUMP BEARINGS – Fill the bearing frame according to the
oiling instructions decal. At the time of installation, add
approximately 1 oz. of B&G #20 weight non-detergent oil.
An SAE 20 (non-detergent) or 10W-30 oil may be substituted.
Re-lubrication is required at the start of each heating sea-
son, or every three months for continuous service. Re-
lubricate with 1 teaspoon of oil. More frequent lubrication
may be required under adverse conditions such as high
ambient temperatures. Less frequent lubrication is required
if oil overflows from the reservoir.
2. MOTOR BEARINGS – Lubricate through the two motor oil
cups according to the lubrication decal. At the time of
installation the motor bearings use approx. 12 drops each.
At re-lubrication intervals fill each motor bearing with
approx. 6-8 drops. More or less frequent re-lubrication
may be required depending on the installation conditions.
NOTE: Over-oiling can cause motor mount deterioration and
may cause spillage onto surrounding surfaces. Deteriorated
motor mounts will lead to misalignment and excessive coupler
wear.
PRIMING AND STARTING
Do not run B&G circulator pumps dry. Before starting, the
pump must be filled with water. Air should be vented from the
system by means of a system air vent or by an alternate method.
1. Remove the screws securing the conduit box cover (wiring
compartment) and lift off the cover. Attach the appropriate
size connector to the hole in the side of the conduit box.
2. Using a minimum size 14 AWG copper electrical wire (refer
to your local code for wiring restrictions), wire the motor to
a 115 volt, 60 hertz, single phase power source.
3. Connect the ground wire to the green screw inside the
conduit box.
NOTE: Single phase motors are protected with inherent over-
heating devices and do not require external overload protection.
NOTE: If a motor with special characteristics is selected, the
electrical rating of the power source must be the same as that
of the motor.
WARNING: ELECTRICAL SHOCK HAZARD
Disconnect and lockout the power before making
electrical connections. Failure to follow these instructions
could result in serious personal injury or death.
TO REMOTE
CONTROL
IF REQUIRED
TYPICAL WIRING INSTALLATION SCHEMATIC
POWER SOURCE: 115 VOLT, 60 HZ, 10
FUSIBLE DISCONNECT
OR CIRCUIT BREAKER
BY OTHERS
PUMP MOTOR
THERMALLY
PROTECTED
PUMP
MOTOR
LN
WARNING: ELECTRICAL SHOCK HAZARD
Be certain that all connections are secure and the
conduit box cover is closed before electrical power is con-
nected. Failure to follow these instructions could result in
serious personal injury, death and/or property damage.
OPERATIONAL INSTRUCTIONS
CAUTION: SEAL DAMAGE HAZARD
Do not run the pump dry – seal damage may occur.
Failure to follow these instructions could result in moderate
personal injury and/or property damage.
SERVICE INSTRUCTIONS ADDITIONAL PUMP REPAIR
WIRING INSTRUCTIONS
Xylem Inc.
8200 N. Austin Avenue
Morton Grove, Illinois 60053
Phone: (847) 966-3700
Fax: (847) 965-8379
www.xyleminc.com/brands/bellgossett
Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.
© 2012 Xylem Inc. P81748F April 2012