10510 2 B&G 113210 Instructions User Manual

User Manual: Pump 10510 2 B&G 113210 Instructions

Open the PDF directly: View PDF PDF.
Page Count: 4

SAFETY
INSTRUCTIONS
This safety alert symbol will be used in this manual and on the
pump Safety Instruction decal to draw attention to safety related
instructions. When used, the safety alert symbol means AT-
TENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
FAILURE TO FOLLOW THE INSTRUCTIONS MAY RESULT IN
A SAFETY HAZARD.
APPLICATION
To increase the overall efficiency of a hot water recirculation
system, the TC-1 timer control kit and the AQS-1/2and AQS-3/4
aquastat kits can be installed for use on any B&G NRF, NBF or
Series PL circulator. The TC-1 timer control is programmable
to turn the circulator ON and OFF automatically at preset
times. The aquastat kits switch the pump OFF at 120°F
(48.9°C) and ON at 100°F (37.8°C). The timer and aquastat kits
can be used in combination or they can be used separately.
This permits the user to have the pump circulate hot water
only during those times when high usage can be expected
throughout the day. When the aquastat kit and timer are used
together, the pump will only circulate water when the ON time
conditions are met and when the water temperature is low
enough to cause the aquastat to switch ON.
OPERATIONAL LIMITS
For use on B&G models NRF/NBF/Series PL, indoor use only
Power supply: 115-120 VAC, 60Hz, 1Ø
Minimum switch interval: 15 minutes
Run Modes: ON (continuous run), OFF (off at all times), TIMER
(run at programmed intervals)
Maximum switch current: 16 amps
Aquastat switch modes: OFF (open) at 120°F (48.9°C) and ON
(closed) at 100°F (37.8°C)
Aquastat type: Bimetal element, senses surface temperature
of outside diameter of pipe
Pipe Size: AQS-1/2clips onto 1/2" copper pipe or 3/8" steel pipe
(OD of pipe 5/8")
AQS-3/4clips onto 3/4" copper pipe or 1/2" steel pipe
(OD of pipe 7/8")
Mounting: May be installed to sense temperature at the suc-
tion or discharge pipe of the pump
NOTE! Aquastat operation is dependent on ambient eviron-
ment. In installations with excessive heat gain or loss in the
ambient may affect the on/off operating temperatures.
INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER’S USE.
Bell & Gossett
Automatic Timer Kit Model TC-1
Aquastat Models AQS-1/2, AQS-3/4
Pumps With Plug-In Cords
INSTRUCTION MANUAL
P58749C
TIMER INSTALLATION
1. Disconnect the electrical supply to the pump.
2. Remove the screw that holds the steel conduit box cover
to the pump.
3. Remove the conduit box cover. The timer assembly replaces
the conduit box cover.
4. Disconnect the black and white motor leads from the power
supply.
5. Position the plastic base for the timer assembly onto the
steel conduit box with the warning/caution label to the rear
of the pump.
6. Secure the plastic timer base to the conduit box with one
8-32 screw provided.
7. Verify that the electrical rating of the timer matches the
values shown on the nameplate of the circulator.
8. Make the electrical connections according to the wiring
diagram provided. (See Figure 2)
9. Position the cover/timer assembly over the base while
insuring that all wires are inside the box. Note that the
cover/timer assembly can only be assembled in one direc-
tion on the base. Line up the screw holes in the cover with
the screw holes in the base.
10. Fasten the cover to the base using (2) 8-32 screws provided.
AQUASTAT INSTALLATION
1. Follow steps 1 and 2 in the timer installation section.
2. Remove the conduit box cover. If the aquastat is installed
without the timer, the steel cover is reassembled on the
pump after the aquastat installation is complete.
3. Fasten the aquastat clip to the discharge or suction pipe of
the pump.
4. Make the electrical connections according to the wiring
diagram provided. (See Figure 1)
5. Reassemble the conduit box cover to the conduit box while
insuring that all wires are inside the box. Reinstall the 8-32
screw to secure the cover to the conduit box.
WARNING: ELECTRICAL SHOCK HAZARD
Disconnect and lock out the power before making
electrical connections. Failure to follow these instructions
could result in serious personal injury or death.
2
WARNING: ELECTRICAL SHOCK HAZARD
Electrical connections are to be made by a qualified
electrician in accordance with all applicable codes, ordi-
nances and good practices. Failure to follow these instruc-
tions could result in serious personal injury, death and/or
property damage.
WARNING: ELECTRICAL SHOCK HAZARD
Electrical connections are to be made by a qualified
electrician in accordance with all applicable codes, ordi-
nances and good practices. Failure to follow these instruc-
tions could result in serious personal injury, death and/or
property damage.
FIGURE 1
BLACK
WHITE
WHITE
BLACK
BLACK
WHITE
WHITE
BLACK
54321
L
WHITE
N
LBLACK
CAPACITOR
TIMER
AQUASTAT
FIGURE 2
CAPACITOR
FIGURE 5
PROGRAMMING
RING
TIMING ARROW
ON, OFF, AUTO SWITCH
PROGRAMMING
TABS
REAL TIME
CLOCK
AQUASTAT AND TIMER INSTALLATION
1. Follow the installation steps in both sections and see
Figure 3 for wiring connections.
TIMER PROGRAMMING
1. Adjust the programming ring on the unit by turning it in the
direction of the rotation arrow until the timing arrow points
to the actual time of day. (This can also be accomplished
by rotating the minute hand on the real time clock, (shown
in figure 5) clockwise, until both the real time clock and the
timing arrow indicate the actual time of day.)
2. Restore power to the circulator and set the switch on the
timer dial to the “I” (ON) position.
3. Program the “ON/OFF” times by pushing the programming
tabs toward the center of the dial for “OFF” operation and
toward the outside of the programming ring for “ON” time
periods. A pencil, pen or similar object may be used in
making adjustments to the programming tabs.
4. Set the manual switch to the “TIMER” position, which is
centered between the “I” and “O” on the timer dial, in
order to cycle the pump according to the programming tab
settings. The pump will run continuously when the switch
is set to the “I” (ON) position. The “O” (OFF) position of the
switch will shut the circulator off at all times.
5. In the event of a power outage, the timer must be adjusted
for the correct time of day after power is restored.
3
FIGURE 3
FIGURE 4
BLACK
WHITE
BLACK
WHITE N
L
BLACK
CAPACITOR
AQUASTAT
TIMER
POWER
LEADS SUPPLIED BY
OTHERS
WHITE
54321
PUMPS WITH FLEXIBLE CORD
1. Refer to instruction Manual P58671 or P48419 for installa-
tion of the pump.
2. If your pump is equipped with a flexible cord, insert the
115V plug into a properly grounded 115V outlet. (see
Figure 6)
WARNING: ELECTRICAL SHOCK HAZARD
This pump is supplied with a grounded conductor. To
reduce the risk of electric shock, connect only to a properly
grounded, grounding-type receptacle. Failure to follow
these instructions could result in serious personal injury or
death.
FIGURE 6
Xylem Inc.
8200 N. Austin Avenue
Morton Grove, Illinois 60053
Phone: (847) 966-3700
Fax: (847) 965-8379
www.xyleminc.com/brands/bellgossett
Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.
© 2012 Xylem Inc. P58749C May 2012

Navigation menu