86914 5 Berkeley B78660 Repair Parts I

86911 5 Berkeley B66490S Repair Parts I 86911_5_Berkeley B66490S Repair Parts I

86904 5 Berkeley B66488S Repair Parts I 86904_5_Berkeley B66488S Repair Parts I

86907 5 Berkeley B54500 Repair Parts I 86907_5_Berkeley B54500 Repair Parts I

86912 5 Berkeley B66833S Repair Parts I 86912_5_Berkeley B66833S Repair Parts I 86912_5_Berkeley B66833S Repair Parts I pdf pumpproducts

86786 5 Berkeley B54499 Repair Parts I 86786_5_Berkeley B54499 Repair Parts I 86786_5_Berkeley B54499 Repair Parts I pdf pumpproducts

: Pump 86914 5 Berkeley B78660 Repair Parts I 86914_5_Berkeley B78660 Repair Parts I pdf

Open the PDF directly: View PDF PDF.
Page Count: 8

Cast Iron Impeller B1-1/2Zpl
Threaded Case (NPT) Packing Construction
Item Part Description Part Number
1A Case, Volute L01025
1B Case, Volute L03075
2 Impeller See Table I
13A Rings, Packing (Set of 7) S15094
13B Rings, Packing (Set of 6) S13470
14A Sleeve, Shaft (2 Req.) S00619L
14B Sleeve, Shaft S05149L
17A Gland, Packing B82469
17B Gland, Packing B82470
26A Screw, Impeller 3/8 - 16 x 1” S23566
26B Screw, Impeller 1/2 - 13 x 1” S23619
32A Key, 3/16 x 1-1/4” (See Note 1) S34383
32B Key, 1/4 x 2/14” (See Note 1) S23677
69A Washer, Impeller S06314
69B Washer, Impeller S06317
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
800A Capscrew, 3/8 - 16 x 1” (12 Req.) S26826
800B Capscrew, 3/8 - 16 x 1-1/8” (8 Req.) S26827
800C Capscrew, 1/2 - 13 x 1-1/2” (4 Req.) S26916
801A Stud, 3/8 - 16 x 3” (2 Req.) S04439
801B Stud, 3/8 - 16 x 4” (2 Req.) S08303
802 Nut, Hex 3/8 - 16 (2 Req.) S23343
805A Washer, Lock S23036
805B Washer, Lock S23038
810 Plug, Pipe 1/4 NPT (5 Req.) S23715
13A (7/8 U)
13B (1-1/4 U)
14A (7/8 U)
14B (1-1/4 U)
17A (7/8 U)
17B (1-1/4 U)
801A (7/8 U)
801B (1-1/4 U)
802
1741 1210
1A (7/8 U)
1B (1-1/4 U)
810
800A
800C (1-1/4U)
800B (7/8 U)
805A (7/8 U)
805B (4-1/4 U)
71
26A (7/8 U)
26B (1-1/4 U)
69A (7/8 U)
69B (1-1/4 U)
73
2
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
7.5 1 L03827 8-1/2” 1-1/4” 213JP
7.5 3 H00950 4-1/2” 7/8” 184JP
10 1 L03827 8-1/2” 1-1/4” 215JP
10 3 L03827 8-1/2” 1-1/4” 213JP
15 3 L03827 8-1/2” 1-1/4” 215JP
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B53750 7.5 1 3600 1-1/4” 7.18” M07692
B53751 7.5 3 3600 7/8” 7.18” M07693
B55574 10 1 3600 1-1/4” 7.88” M07691
B53752 10 3 3600 1-1/4” 7.88” M07691
B53753 15 3 3600 1-1/4” 8.75” M07690
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.1
Date July 1, 2011
Supersedes 1/1/04
1496 1210
T
r
u
a
r
c
1
810
815
800A
800B
805
71
26
69
73
2
89
14
Cast Iron Impeller B1-1/2Zpls
Threaded Case (NPT) Mechanical Shaft Seal Construction
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B54499 7.5 1 3600 7/8” 7.18” M07693
B54500 7.5 3 3600 7/8” 7.18” M07693
B54646 10 1 3600 7/8” 7.88” M07758
B54502 10 3 3600 7/8” 7.88” M07758
B54504 15 3 3600 7/8” 8.75” M07759
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
7.5 1 L05331 8-1/2” 7/8” 213JM
7.5 3 L05332 4-1/2” 7/8” 184JM
10 1 L05331 8-1/2” 7/8” 215JM
10 3 L05331 8-1/2” 7/8” 213JM
15 3 L05331 8-1/2” 7/8” 215JM
Item Part Description Part Number
1Case, Volute L01025
2 Impeller See Table I
14 Sleeve, Shaft S19310L
26 Screw, Impeller 3/8 - 16 x 1” S23566
32 Key, 3/16 x 1-1/4” (See Note 1) S34383
69 Washer, Impeller S06314
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
89 Seal, Mechanical Shaft S32014
800A Capscrew, 3/8 - 16 x 1” (8 Req.) S26826
800B Capscrew, 1/2 - 13 x 1” (4 Req.) S26912
805 Washer, Lock S23036
810 Plug, Pipe 1/4 NPT (5 Req.) S23715
815 Ring, Retaining S11207
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.2
Date July 1, 2011
Supersedes 1/1/04
1602 1210
T
r
u
a
r
c
1
810
815
800A
800B
805
71
26
69
73
2
89
14
Cast Iron Impeller B1-1/2Zpls
Threaded Case (NPT) Mechanical Shaft Seal Construction
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B08607 20 3 3600 1-1/4” 9.00” M02928
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
20 3 L04615 8-1/2” 1-1/4” 254JM
Item Part Description Part Number
1Case, Volute L03075
2 Impeller See Table I
14 Sleeve, Shaft S18869L
26 Screw, Impeller 1/2 - 13 x 1” S23619
32 Key, 1/4 x 2-1/4’’ (See Note 1) S23677
69 Washer, Impeller S06319
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
89 Seal, Mechanical Shaft S32015
800A Capscrew, 3/8 - 16 x 1-1/8” (8 Req.) S26827
800B Capscrew, 1/2 - 13 x 1” (4 Req.) S26912
805 Washer, Lock S23038
810 Plug, Pipe 1/4 NPT (5 Req.) S23715
815 Ring, Retaining S16767
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.3
Date July 1, 2011
Supersedes 1/1/04
13A (7/8 U)
13B (1-1/4 U)
14A (7/8 U)
14B (1-1/4 U)
17A (7/8 U)
17B (1-1/4 U)
801A (7/8 U)
801B (1-1/4 U)
802
1741 1210
1A (7/8 U)
1B (1-1/4 U)
810
800A
800C (1-1/4U)
800B (7/8 U)
805A (7/8 U)
805B (4-1/4 U)
71
26A (7/8 U)
26B (1-1/4 U)
69A (7/8 U)
69B (1-1/4 U)
73
2
BronZe Impeller B1-1/2Zpl
Threaded Case (NPT) Packing Construction
Item Part Description Part Number
1A Case, Volute L01025
1B Case, Volute L03075
2 Impeller See Table I
13A Rings, Packing (Set of 7) S15094
13B Rings, Packing (Set of 6) S13470
14A Sleeve, Shaft (2 Req.) S00619L
14B Sleeve, Shaft S05149L
17A Gland, Packing B82469
17B Gland, Packing B82470
26A Screw, Impeller 3/8 - 16 x 1” S23566
26B Screw, Impeller 1/2 - 13 x 1” S23619
32A Key, 3/16 x 1-1/4” (See Note 1) S34383
32B Key, 1/4 x 2/14” (See Note 1) S23677
69A Washer, Impeller S06314
69B Washer, Impeller S06317
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
800A Capscrew, 3/8 - 16 x 1” (12 Req.) S26826
800B Capscrew, 3/8 - 16 x 1-1/8” (8 Req.) S26827
800C Capscrew, 1/2 - 13 x 1-1/2” (4 Req.) S26916
801A Stud, 3/8 - 16 x 3” (2 Req.) S04439
801B Stud, 3/8 - 16 x 4” (2 Req.) S08303
802 Nut, Hex 3/8 - 16 (2 Req.) S23343
805A Washer, Lock S23036
805B Washer, Lock S23038
810 Plug, Pipe 1/4 NPT (5 Req.) S23715
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B66487 7.5 1 3600 1-1/4” 7.18” L06648
B66488 7.5 3 3600 7/8” 7.18” L06649
B66491 10 1 3600 1-1/4” 7.88” L06647
B66492 10 3 3600 1-1/4” 7.88” L06647
B66493 15 3 3600 1-1/4” 8.75” L06646
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
7.5 1 L03827 8-1/2” 1-1/4” 213JP
7.5 3 H00950 4-1/2” 7/8” 184JP
10 1 L03827 8-1/2” 1-1/4” 215JP
10 3 L03827 8-1/2” 1-1/4” 213JP
15 3 L03827 8-1/2” 1-1/4” 215JP
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.4
Date July 1, 2011
Supersedes 1/1/04
1496 1210
T
r
u
a
r
c
1
810
815
800A
800B
805
71
26
69
73
2
89
14
BronZe Impeller B1-1/2Zpls
Threaded Case (NPT) Mechanical Shaft Seal Construction
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B66489 7.5 1 3600 7/8” 7.18” L06649
B66490 7.5 3 3600 7/8” 7.18” L06649
B66832 10 1 3600 7/8” 7.88” L06609
B66833 10 3 3600 7/8” 7.88” L06609
B66841 15 3 3600 7/8” 8.75” L06610
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
7.5 1 L05331 8-1/2” 7/8” 213JM
7.5 3 L05332 4-1/2” 7/8” 184JM
10 1 L05331 8-1/2” 7/8” 215JM
10 3 L05331 8-1/2” 7/8” 213JM
15 3 L05331 8-1/2” 7/8” 215JM
Item Part Description Part Number
1Case, Volute L01025
2 Impeller See Table I
14 Sleeve, Shaft S19310L
26 Screw, Impeller 3/8 - 16 x 1” S23566
32 Key, 3/16 x 1-1/4” (See Note 1) S34383
69 Washer, Impeller S06314
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
89 Seal, Mechanical Shaft S32014
800A Capscrew, 3/8 - 16 x 1” (8 Req.) S26826
800B Capscrew, 1/2 - 13 x 1” (4 Req.) S26912
805 Washer, Lock S23036
810 Plug, Pipe 1/4 NPT (5 Req.) S23715
815 Ring, Retaining S11207
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.5
Date July 1, 2011
Supersedes 1/1/04
1602 1210
T
r
u
a
r
c
1
810
815
800A
800B
805
71
26
69
73
2
89
14
sIlICon BronZe Impeller B1-1/2Zpls
Threaded Case (NPT) Mechanical Shaft Seal Construction
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B78660 20 3 3600 1-1/4” 9.00” H05465
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
20 3 L04615 8-1/2” 1-1/4” 254JM
Item Part Description Part Number
1Case, Volute L03075
2 Impeller See Table I
14 Sleeve, Shaft S18869L
26 Screw, Impeller 1/2 - 13 x 1” S23619
32 Key, 1/4 x 2-1/4’’ (See Note1) S23677
69 Washer, Impeller S06317
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
89 Seal, Mechanical Shaft S32015
800A Capscrew, 3/8 - 16 x 1-1/8” (8 Req.) S26827
800B Capscrew, 1/2 - 13 x 1” (4 Req.) S26912
805 Washer, Lock S23038
810 Plug, Pipe 1/4 NPT (5 Req.) S23715
815 Ring, Retaining S16767
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.6
Date July 1, 2011
Supersedes 1/1/04
13A (7/8 U)
13B (1-1/4 U)
14A (7/8 U)
14B (1-1/4 U)
17A (7/8 U)
17B (1-1/4 U)
801A (7/8 U)
801B (1-1/4 U)
802
1741 1210
1A (7/8 U)
1B (1-1/4 U)
810
800A
800C (1-1/4U)
800B (7/8 U)
805A (7/8 U)
805B (4-1/4 U)
71
26A (7/8 U)
26B (1-1/4 U)
69A (7/8 U)
69B (1-1/4 U)
73
2
sIlICon BronZe Impeller B1-1/2Zpl
Threaded Case (NPT) Packing Construction
Item Part Description Part Number
1A Case, Volute L01025
1B Case, Volute L03075
2 Impeller See Table I
13A Rings, Packing (Set of 7) S15094
13B Rings, Packing (Set of 6) S13470
14A Sleeve, Shaft (2 Req.) S00619L
14B Sleeve, Shaft S05149L
17A Gland, Packing B82469
17B Gland, Packing B82470
26A Screw, Impeller 3/8 - 16 x 1” S23566
26B Screw, Impeller 1/2 - 13 x 1” S23619
32A Key, 3/16 x 1-1/4” (See Note1) S34383
32B Key, 1/4 x 2/14” (See Note1) S23677
69A Washer, Impeller S06314
69B Washer, Impeller S06317
71 Bracket See Table II
73 O-Ring (See Note 2) M14943
800A Capscrew, 3/8 - 16 x 1” (8 Req.) S26826
800B Capscrew, 3/8 - 16 x 1-1/8” (4 Req.) S26827
800C Capscrew, 1/2 - 13 x 1-1/2” (4 Req.) S26916
801A Stud, 3/8 - 16 x 3” (2 Req.) S04439
801B Stud, 3/8 - 16 x 4” (2 Req.) S08303
802 Nut, Hex 3/8 - 16 (2 Req.) S23343
805A Washer, Lock S23036
805B Washer, Lock S23038
810 Plug, Pipe 1/4” NPT (5 Req.) S23715
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B66487S 7.5 1 3600 1-1/4” 7.18” H05458
B66488S 7.5 3 3600 7/8” 7.18” H05459
B66491S 10 1 3600 1-1/4” 7.88” H05460
B66492S 10 3 3600 1-1/4” 7.88” H05460
B66493S 15 3 3600 1-1/4” 8.75” H05461
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
7.5 1 L03827 8-1/2” 1-1/4” 213JP
7.5 3 H00950 4-1/2” 7/8” 184JP
10 1 L03827 8-1/2” 1-1/4” 215JP
10 3 L03827 8-1/2” 1-1/4” 213JP
15 3 L03827 8-1/2” 1-1/4” 215JP
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.7
Date July 1, 2011
Supersedes 1/1/04
1496A 1210
T
r
u
a
r
c
1
810
815
800A
800B (4-1/2 AK)
800C (8-1/2 AK)
805
71
26
69
73
2
89
14
sIlICon BronZe Impeller B1-1/2Zpls
Threaded Case (NPT) Mechanical Shaft Seal Construction
Table I
B/M No. HP PH RPM ‘‘U’’ Dim. Imp. Dia. Imp. No.
B66489S 7.5 1 3600 7/8” 7.18” H05459
B66490S 7.5 3 3600 7/8” 7.18” H05459
B66832S 10 1 3600 7/8” 7.88” H05463
B66833S 10 3 3600 7/8” 7.88” H05463
B66841S 15 3 3600 7/8” 8.75” H05464
Table II
HP PH Bracket No. ‘‘AK’’ Fit ‘‘U’’ Dim. Motor Frame
7.5 1 L05331 8-1/2” 7/8” 213JM
7.5 3 L05332 4-1/2” 7/8” 184JM
10 1 L05331 8-1/2” 7/8” 215JM
10 3 L05331 8-1/2” 7/8” 213JM
15 3 L05331 8-1/2” 7/8” 215JM
Item Part Description Part Number
1Case, Volute L01025
2 Impeller See Table I
14 Sleeve, Shaft S19310L
26 Screw, Impeller 3/8 - 16 x 1” S23566
32 Key, 3/16 x 1-1/4” (See Note 1) S34383
69 Washer, Impeller S06314
71 Bracket See Table II
73 O-Ring (See Note 3) M14943
89 Seal, Mechanical Shaft S32014
800A Capscrew, 3/8 - 16 x 1” (8 Req.) S26826
800B Capscrew, 3/8 - 16 x 1” (4 Req.) S26826
800C Capscrew, 1/2 - 13 x 1” (4 Req.) S26912
805 Washer, Lock S23036
810 Plug, Pipe 1/4” NPT (5 Req.) S23715
815 Ring, Retaining S11207
•Plug, Pipe 1/8” NPT (In Bracket) S23714
• Not illustrated.
NOTE 1: For an explanation of the tabulated material found on
this page and for impeller key location, refer to Supplement A
located at the beginning of this section.
NOTE 2: For seal flush line details, see Supplement D.
NOTE 3: Also accepts gasket S05126 as replacement for o-ring.
See Supplement E located at the beginning of this section.
Type ‘‘B’’ Single Stage
Centrifugal Pump
Electric Motor Drive
Form No. S4855BK
Section CC
Page 40.8
Date July 1, 2011
Supersedes 1/1/04

Navigation menu