Pyle Audio Psw501Sf Users Manual 35303153462D5332D0CDB8BDBCFEB0FC2834C3B6C5F2D5CDA3A930382E31312E31392E636472

PSW501SF PSW501SF

PSW501SF to the manual 3139ebfe-a91a-41fa-85b7-125b765b095c

: Pyle-Audio Pyle-Audio-Psw501Sf-Users-Manual-522102 pyle-audio-psw501sf-users-manual-522102 pyle-audio pdf

Open the PDF directly: View PDF .
Page Count: 4

Download
Open PDF In Browser	View PDF

Step 4: Hanging display
Firstly lift the bracket mounted display over the wall mount. And then hook the
brackets over the top of the wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown in Fig.4a. Then put safe
bolts into the bottom of the brackets and lock it, as shown in Fig.4b.
Warning: Some TV require two people to lift, as we are not responsible for any
personal injury or product damage due to mishandling.

Fixed Flat Panel TV Bracket
Multifunctional double deck wall mount
INSTALLATION GUIDE
Item No.:PSW501SF

2

1
4
the facing of a quilt

Fig 4a

Fig 4b

Thank you for choosing our products

Easy installing: Just hang up the display
Safety: locking by spinning bolt on the bottom
Max load capacity:50kgs/110lbs

Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000

TV size range: 26 " ~42 "

Inside has balance adjust system
Bulit in leveler system

-8-

www . pyleaudio . com
MADE IN CHINA

IMPORTANT: If don’t understand about right install ways, please
consult to normal installing specialist.

Hardware List: Actual parts appearance and the quantity may different
with illustrated.
2

2
Wooden wall:
Using a awl or nail to make where the nails are located, as shown as Fig.3b. Distance
between two nails for fixing wall mount must not less than 16”. Slide the plate into
position as required.(Fig.3c) Pre-drill these holes with a 5mm drill bit to at least
40mm in deep hole. Use wall mount as a template to mark the location of other three
holes and drill the same holes. Please make sure these holes are level and eudipleural.
Fix the wall mount to the wall with 4 long bolts(H) and washers(J) by Box wrench(5) .

1

Brick, Concrete and Stone wall:
Using a awl or nail to make where the nails are located. Distance between two nails
for fixing wall mount must not less than 16 ” . Slide the plate into position as required.
(Fig.3c) Pre-drill these holes with a 10mm drill bit to at least 50mm in deep hole. Use
wall mount as a template to mark the location of other three holes and drill the same
holes. Please make sure these holes are level and eudipleural. Insert wall anchors(I)
into each of these holes. Attach the wall mount to the wall using 4 long bolts(H) and
washers(J) by Box wrench(5).

5
3
4

A-F

ID
1
2

Qty
1
2

3
4
5
A
B

1
2
1
4
4

C

4

After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall -wooden, brick, concrete and stone.

G

I

H

J

Description
Wall mount
Bracket
Cable Cover
Safe bolt

ID
D
E
F
G

Qty
4
4
4
4

Box wrench

H
I
J
K

4
4
4

M4 ×12 mm bolt
M4 ×16 mm bolt
M5× 16 mm bolt

4

Description
M6×16mm bolt
M5×36mm bolt
M6×36mm bolt
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer

K

Plate

Fig 3b
Balance-adjusting
1

J

Fig 3c
Using balance-adjusting system on the plate,
make sure whether wall plate is installed
balance. If not, then slide the wall plate let
pointer level in the center position.

H 5

Fig 3d
-2-

-7-

Step 2: Install the Cable Cover

Route the cables as required. Snap the cable cover into place onto
the rods (Fig. 2a), and then slide the cover into position as required.
(Fig. 2b)

Fig 2a

Fig 2a

Step 3: Attach mount to wall

WARNING
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.

Caution : This Product LCD /Plasma Wall Mount Bracket is intended for use only
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .

First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 3a).
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15°(Fig 3a).

Step 1: Attach bracket to TV

For example:
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.

For correct installing, make sure that hook of every bracket must facing down. Use
selected bolts, spacers and washers for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tightly secure the
bolts.

Check your TV manual to confirm the diameter of bolt to be used or choose an
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4-5 of these instructions for examples.

IMPORTANT:
IMPORTANT Don't force the bolt into the hole, which will cause a damage of
equipments and injure of person. Don't use electric drill to fasten any bolts.

15 degree
viewing angle

b

eyelevel

a
Fig 3a
-6-

-3-

Following examples shows how to use bolts, spacers and square washers.
1.Some displays have vertical backs. No spacer is required. Install the bracket directly
to the back of display by using bolts and square washers provided. As shown in Fig.1a.

M4 Fig bit

2. Some displays have cur ved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(K) between display and
the bracket. As shown in Fig 1b.

Fig a

M5 Fig bit
M5 Fig bit

G

M6 Fig bit

K

A,B

E

2

2

G

K

C
2

2

2

G

G

F

Fig 1b

G

D

M6 Fig bit

Fig 1a

-4-

-5-



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2009:06:25 11:14:12+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2009:06:25 11:14:12+08:00
Format                          : application/pdf
Title                           : <35303153462D5332D0CDB8BDBCFEB0FC2834C3B6C5F2D5CDA3A930382E31312E31392E636472>
Creator                         : Administrator
Document ID                     : uuid:49598451-9bf8-4e13-bf06-e20810e4e93a
Instance ID                     : uuid:3c5c0189-cb9a-449c-9b0c-0cd956a4232d
Page Count                      : 4
Author                          : Administrator

EXIF Metadata provided by EXIF.tools