Pyramid Car Audio Pa1000X Users Manual
PA800X to the manual 2f73fcfc-b892-46bd-8aa3-e2451187975a
2015-02-06
: Pyramid-Car-Audio Pyramid-Car-Audio-Pa1000X-Users-Manual-522208 pyramid-car-audio-pa1000x-users-manual-522208 pyramid-car-audio pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
® Studio PRO High Performance Professional Audio MODEL:PA600X/PA800X/PA1000X/ PA1800X PA AMPLIFIER www.pyramidcaraudio.com INTRODUCTION Your New PYRAMID PA SERIES AMPLIFIER gives you the power and versatility you need in a professional sound system. The amplifier's wide frequency response makes it suitable for amplifying music or vocal program material. It can be used for live bands, office paging systems, public announcements, or a variety of other installations. Please read this manual throughly before you attempt to set up and use the amplifier. It contains a range of installation suggestions as well as instructions to ensure safe usage. Installed properly, you can expect years of trouble-free service from this product. FEATURES AND CONTROLS FRONT PANEL - PA600X/PA800X/PA1000X/PA1800X PA600X 1 2 3 8 1 6 8 4 4 PA800X 1 2 3 8 6 4 8 5 4 PA1000X 1 2 3 8 4 6 7 8 6 5 4 PA1800X 2 8 1 2 8 3 FRONT PANEL - PA600X/PA800X / PA1000X/PA1800X 1.Power On/Off 2.Phone Jack Lets you connect a pair of stereo headphones for private listening or cueing (monitoring) sound prior to "airing" it. 3.Speaker A/B Selector Switches Permit you to select speakers attached to terminal set A, set B, or both. 4.Left and Right Power Meters (PA800X/PA1000X/PA1800X) Indicate the output signal level for each channel. 5.Meter Range Switch (PA800X/PA1000X) Controls the sensitivity of the power meter. 6.Clip Circuit and Indicator This special circuitry protects the amplifier and speaker system from being damaged by overdriving power levels. Indicator lights remind the user to reduce the volume when amplifier output is excessive. 7.Protection Circuit and Indicator (PA1800X) The indicator will be illuminated when the amplifier is powered on and at turn-on delay status; the indicator will be turned off after internal outputs are connected. The indicator will also be illuminated when the amplifier has abnormal problems, such as overload or excessive heat. 8.Left and Right Output Level Controls Lets you adjust the sound levels for each channel. In the mono bridged mode (PA1000X/PA1800X), only the left gain control will adjust the output level. REAR PANEL - PA600X e q 9 3 REAR PANEL - PA800X / PA1000X / PA1800X r e w q 9 t 0 REAR PANEL - PA600X / PA800X / PA1000X / PA1800X 9.Voltage Switch The amplifier has selectable input voltage from 110V/60Hz which is the standard in USA and CANADA. You can also switch the input voltage to 220V/50Hz for EUROPEAN operation. Please make sure the switch is in the proper position before operating, otherwise severe damage will result not cover by the warranty. Please also replace the fuse with proper rating in this situation (see the SPECIFICATIONS for the fuse rating). 10.Switched AC Accessory Outlet (PA800X/PA1000X/PA1800X) There is supplied AC OUTLET (SWITCHED MAX. 400W) which allow the electrical hook up of other units. 11.Speaker Terminals Permits hook up of two stereo pair of speakers via the wire terminals. You can choose either Channel A , Channel B, or use both at the same time. Speaker impedance can range from 4 to 16 Ohms. 12.Fan Cooling (PA800X/PA1000X/PA1800X) Cooling system is automatically activated whenever amplifier is turned on. This forced air cooling system rapidly exhausts interior heat, reducing operating temperature and aiding performance. 13.Input Jacks Let you connect a variety of audio input sources via the balanced 6.35mm phone jack or unbalanced RCA inputs. 14.Stereo/Mono Switch (PA1000X/PA1800X) Lets you select bridged mono input mode in combination with a mono signal source plugged into the LEFT input channel, or conventional stereo operation with a stereo input signal. 15.Mono Bridged Output (PA1000X/PA1800X) Connect the speaker's positive (+) to the amplifier's LEFT/RED (+) terminal and negative (-) to the amplifeir's RIGHT/RED (+) terminal. 4 Stereo or Mono Inputs (PA1000X/PA1800X) INSTALLATION GUIDELINES The PA1000X and PA1800X can be operated in Stereo or Mono mode, depending on the input source. If the input signal is mono, connect the source via the LEFT input only (also marked "MONO" on the back of amplifier). Then slide the STEREO/MONO selector switch to MONO and the signal will be routed through both channels. Connecting the GND (GROUND) screw terminal Connecting a mixer or preamplifier may cause excessive noise or hum in the amplifier output. To prevent this, connect one end of a low-capacitance shield wire to the amplifier's ground screw (on the rear panel). Then connect the other end of this wire to the ground terminal on the mixer or preamplifier enclosure. MONO SIGNAL SOURCE EQ OR MIXER STEREO/MONO SWITCH IN "MONO" POSITION Speaker connections LOW CAPACITANCE SHIELD WIRE GROUND SCREW You can connect 4 Ohm, 8 Ohm, or 16 Ohm speakers to Channel A and/or Channel B of the amplifier. If you connect two pairs of speakers, be sure to follow these guidelines: • Speakers which are connected to the same channel are part of a pair, and must be of the same impedance. • Speakers connected to different channels are NOT part of a pair, and can be of different impedances. Input connections These amplifiers accept a board range of input sources, including Compact Disc (CD) players; Cassette, Reelto-Reel or other tape players; Radio Tuners; Equalizers; Signal Processors. Connecting a CD or tape player, or tuner In a normal installation, one would use the RCA JACKS for connecting a CD player, tape player or tuner. use RCA jacks 1.Prepare the speaker wire by removing about 1 inch of insulation from the end of speaker wire you intend to connect to the amplifier. Then twist the exposed wire to secure all the wire strands. NOTE:Use 18-gauge speaker wire for lengths up to 25 feet; 16-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible. 2.Connect the speaker wire to the speaker's positive and negative terminals. CD PLAYER, TAPE PLAYER OR TUNER NOTE:Most speaker terminals are either color-coded or have a mark that indicates the terminal's polarity. Usually positive terminals are red or have a plus symbol (+), and negative terminals are black or have a minus symbol (-). Connecting an equalizer or external signal processor Connect the processor's OUT to the amplifier's IN connector. EQ OR MIXER 3.Connect the speaker wires to the amplifier's left and right speaker terminals according to the terminal color polarity. use 6.35mm phone jacks R L 4 OHMS MIN. IMPEDANCE SPEAKER MUST BE OF SAME IMPEDANCE. use RCA jacks EQ OR MIXER 5 Bridge Mode Operation (PA1000X/PA1800X) Turning the amplifier on The PA1000X and PA1800X can be operated in mono bridged output mode, if your speakers can handle the following power output levels: 1.Turn on the audio input source equipment which is connected to the amplifier INPUT jack. 2.Set the amplifier's left and right output level gain controls to the minimum level settings. 3.Press the power switch to turn the amplifier on. PA1000X: 320 watts PA1800X: 420 watts Using the power meter (PA800X/PA1000X/PA1800X) As shown in the diagram below, connect the speaker's positive (+) to the amplifier's red speakers left (A/B) terminals and negative (-) to red speakers right (A/B) terminals. The meter POINTER (PA800X/PA1000X) and/or LED (PA1800X) position indicate the amplifier output power. For ease of reading in dark environments, the VU meter (PA800X/PA1000X) is illuminated. The speaker righr (+) on the amplifier is used a negative (-) terminal for a bridged connection. Using the meter range selector (PA800X/PA1000X) NOTE: IT IS SUGGESTED TO USE A 8-OHM SPEAKER FOR THE ONE CHANNEL BRIDGE HOOKUP. IF YOU CONNECT TWO CHANNELS' BRIDGE HOOKUP, PLEASE MAKE SURE THE SPEAKER IMPEDANCE MUST BE 8-OHM MINIMUM. STEREO/MONO SWITCH IN "MONO" POSITION When output power is too strong, the meter's pointer might continuously swing to the extreme right and damage or reduce the accuracy of the meter. To protect the meter, you can use the meter range selector to control the amplifier's sensitivity to the input power signal. Leave the meter range switch in the OUT position to maintain a 0 dB gain for the mater. When output power is not strong, leave the meter range switch in the IN position to allow a +20dB gain. BRIDGED SPEAKER HOOKUP Using the left and right Output Level controls Rotate output level gain clockwise to increase, or counterclockwise to decrease the output power. To get the best performance with the leaset sound distortion, always adjust the output level gain so the meter's level indication does not continuously exceed to the extreme right. Using headphones To listen privately, or to monitor sound sources, connect a pair of low impedance stereo headphones (not supplied) with 6.35mm plug into the PHONES jack on the amplifier front panel. Please listen safely. Follow these recommendations: Do not listen at extremely high volume levels. Extended, high-volume listening can lead to permanent hearing loss. CAUTION: It is possible to overdrive the amplifier by setting output level gain too high, which may cause damage or failure. About the internal clip circuitry Special clip circuitry incorporated into your amplifier's design protects the amplifier and speaker system from being damaged from overdriving power. Always start with the volume control set to a LOW level BEFORE you put the headphones on. Then gradually increase the volume as necessary. Under normal conditions, the amplifier's clip indicator will flicker as the output power momentarily exceeds the level as set by the output level gain selector. Connecting to standard AC power After making all other connections, set the POWER switch to OFF position. Then connect the power cord to a standard AC outlet. However, under excessive output conditions, the clip indicator lights remain on continuously, altering you that the special clip circuitry has become active. When this occurs, you should simply reduce the output power level by rotating the Master Volume control counterclockwise. Mounting the amplifier This amplifier is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation. Tightly secure four mounting screws (not supplied) through these four slots and into your standard electronics equipment rack. Using the A/B Speaker Selector Switch You can listen to speakers on set A or set B individually or simultaneously. Simply push in or out the desired speaker set to make your selection. 6 CAUTION: If the impedance of your speakers is 4 OHMS, do not use both the speaker A and speaker B terminal at the same time as the net impedance may be low enough to damage your amplifier. Replacing a fuse Caring for your PYRAMID amplifier Remove the old fuse and replace it with an identical, serviceable fuse: This amplifier requires a fuse with the proper rating for protection from power surges and short circuits. If the amplifier suddenly turns off or will not turn on, the fuse is properly blown. Your PYRAMID amplifier is an example of superior design and craftsmanship. The following suggestions will help you care for your amplifier so you can enjoy years of use: • Keep the amplifier dry. If it gets wet, wipe immediately. • Use the amplifier only in well-ventilated installations. • Handle the amplifier away from dust and dirt. • Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemical, solvents or detergents! PA600X = 6A (110-120V) OR 3A (220-240V) PA800X = 6A (110-120V) OR 3A (220-240V) PA1000X = 6A (110-120V) OR 3A (220-240V) PA1800X = 7A (110-120V) OR 3.5A (220-240V) CAUTION: Never use a fuse with a higher rating. Amplifier Specifications PA600X PA800X PA1000X PA1800X Input Impedance 20 k-Ohms 20 k-Ohms 20 k-Ohms 20 k-Ohms Continuous Output Power Stereo Mode 20 Hz to 20 kHZ, 8 Ohms 1 kHz, 4 Ohms Maximum power, 8 Ohms Maximum power, 4 Ohms 70W X 2 90W X 2 300W X 2 600W X 2 100W X 2 120W X 2 400W X 2 800W X 2 110W X 2 160W X 2 500W X 2 1000W X 2 160W X 2 210W X 2 900W X 2 1800W X 2 250W X 1 320W X 1 1000W X 1 2000W X 1 350W X 1 420W X 1 1800W X 1 3600W X 1 Bridge Mode 20 Hz to 20 kHZ, 8 Ohms 1 kHz, 4 Ohms Maximum power, 8 Ohms Maximum power, 4 Ohms THD at rated output power Frequency Response +/-3dB Input Sensitivity Signal to Noise Ratio A-Weighted 0.1% 10 Hz to 50 kHz 0.775V 90 dB 0.1% 10 Hz to 50 kHz 0.775V 90 dB 0.1% 10 Hz to 50 kHz 1V 90 dB 0.1% 10 Hz to 50 kHz 1V 90 dB Speaker Impedance A or B ONLY A plus B Bridged Mode 4 - 16 Ohms 8 - 16 Ohms 4 - 16 Ohms 8 - 16 Ohms 4 - 16 Ohms 8 - 16 Ohms 8 - 16 Ohms 4 - 16 Ohms 8 - 16 Ohms 8 - 16 Ohms Power Requirement Power Fuse 110-120V AC 220-240V AC Dimensions H x W x D, inches (mm) Weight, lbs (kg) 120V AC, 60 Hz / 240V AC, 50Hz 6A 3A 4 3/16 X 19 X 10 3/4 100 X 482 X 273 21.78(9.9) 6A 3A 4 15/32 X 19 X 12 130 X 482 X 305 26.84(12.2) 7 6A 3A 4 15/32 X 19 X 12 130 X 482 X 305 26.4(12) 7A 3.5A 5 1/ 8 X 19 X 12 130 X 482 X 305 26.84(12.2)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2004:08:03 18:18:06 Producer : Apogee Series3 Pilot v1.0u1 Modify Date : 2004:08:03 18:30:28+08:00 Page Count : 8EXIF Metadata provided by EXIF.tools