Q Global Solutions IPS20100315 Image Parking System User Manual IPS manual EN
Q Global Solutions (Xiamen) Electronics Corp. Image Parking System IPS manual EN
User Manual
Owner’s Manual of IPS System
Thanks for your purchase of our user-friendly IPS system. IPS is short for Image
Parking System. It is a device designed to assist you in seeing and short distance
obstacle’s detecting. Although IPS provides an excellent assistance, however the
right judgment and decision making is still rested on you.
IPS combines the two most common and useful systems (Camera and ultrasonic sensor)
in one. The Camera system sees the image. The ultrasonic system tells the distance.
On the LCD monitor, it shows sharp image and digital distance reading. It is easy DIY
system with a concealed hole behind the license plate.
1. Purpose of using IPS
The purpose of using IPS is to avoid drilling many holes on a beautiful bumper for
passenger. For various commercial vehicles, they have different available mounting
heights. It is difficult to drill many holes on a big truck, less holes less job. With an
environment learning program within, IPS is a “one system fits all” product.
2. How it works
Camera is located in the center of IPS bar. Through the camera, it catches image.
One ultrasonic sensor locates on each end of the bar. Ultrasonic sensors detect the
distance. The control module receives both Image and Distance data. TX module
transmits the data to the monitor.
3. COMPONENTSCERA 摄取车后的景，将 VIDEO 信
3.1 MONITOR
Bright LCD monitor shows sharp image and Digital reading. Power can be
from ACC source or Cigarette Lighter plug. The monitor stands on the top
of dashboard. It can be adjusted to meet individual need.
3.2 CONTROL BOX
Rigid control module is filled up with non-inflammable potting material to
prevent moisture and absorb certain unexpected shock. The module is
worked with a video TX transmitter. It may be installed in the boot or
lights box. The module could work up to 4 sensors. The module works
with different criteria in different heights from 35cm to 80cm.
3.3 LICENSE PLATE
IPS bar contains sensors, camera and bar shaped holder. Camera and
sensors can be adjusted 35 degrees up and down on either side. It fits all
cars in different height.
3.4 WATCH BUZZER
Watch buzzer’s volume can be fully adjusted. It is recommend that this
buzzer is to be installed inside the cabin.
3.5 VIDEO TX MODULE
This is a video TX module which connects to the control module. It
receives both image and distance data and sends the same digital data to
video RX module connecting to the LCD monitor.
3.6 VIDEO RX MODULE
This is a video RX module which receives the data sending from video TX
module. The module should be concealed behind the dashboard close to the
monitor. (It applies only on RF/wireless system.)
4. SPECIFICATION
RATED VOLTAGE：DC 12V
OPERATION VOLTAGE：9～16V DC
OPERATION TEMPERATURE：-30℃～85℃
EFFECTIVE PIXELS：NTSC:510(H)*496(V)/PAL:628(H)*582(V)
MINIMUM LIIUMINATION：0.1LUX
5. Self-Diagnosis
Once power on, the system starts its self-diagnosis checking
a. 1 beep - The system works well ●
b. 2 beeps - 1 sensor is out of order ●●
c. 3 beeps - 2 sensors are out of order ●●●
d. 4 beeps - 3 sensors out of order ●●●●
Remark: When there are no L and/or R sensors connected, the system deems it has
two sensors.
6. The system’s Distance detection
Once power on, obstacle distance detection starts
a. When obstacle within 3 – 6ft, beeper sounds more rapidly once closer.
b. Solid beep means the obstacle is within 3ft. On monitor screen it shows “Stop”
sign with camera image.
L and R corner alarm within 2ft.
Important:
Whenever you hear solid beeps or see ”stop” sign showing on the screen, you should
immediately stop.
Changes or Modifications not expressly approved by the party reponseible
for compliance could void the user’s authority to operate the equipment.