QNAP Systems QWAAC2600 QNAP Wireless Adapter User Manual

QNAP Systems, Inc. QNAP Wireless Adapter

Contents

User Manual-statement

ComplianceFor more information about safety, regulatory, and environmental compliance, visit www.qnap.com/regulatory/.This device complies with Directive 2014/53/EU issued by the Commission of the European Community.Declaration of ConformityHereby, QNAP Systems, Inc. declares that the radio equipment type EN 301 489-1 V2.1.1EN 301 489-17 V3.1.1EN 300 328 V2.1.1EN 301 893 V2.1.1EN 55032:2012EN 55024:2010EN 50385EN 62311:2008 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following Internet address. www.qnap.com/regulatoryThe frequency and maximum transmitted power in EU are listed as belows,2412-2472MHz: 19.99dBM5180-5240MHz: 22.90dBM5260-5320MHz: 22.99dBM5500-5700MHz: 29.90dBM- WLAN 5GHz:Operations in the 5.15-5.35GHz band are restricted to indoor usage only.經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。應避免影響附近雷達系統之操作。高增益指向性天線只得應用於固定式點對點系統。QNAP Systems, Inc.TEL: +886-2-2641-2000 FAX: +886-2-2641-0555Address: 3F., No.22, Zhongxing Rd., Xizhi Dist., New Taipei City,221, Taiwan
Federal Communication Commission Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 34cm between the radiator & your body.This device is intended only for OEM integrators under the following conditions:1)The antenna must be installed such that 34 cm is maintained between the antenna and users, and 2)The transmitter module may not be co-located with any other transmitter or antenna.As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installedIMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 34 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2ACFN-QWAAC2600”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.Manual Information To the End UserThe OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu