Qiaohua QH-912-2T Transmitter of Wireless Door Chime Kit User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3116670
Application ID	QkFHYAIHTholM5tYzUGhSw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	48.94kB (611769 bits)
Date Submitted	2016-08-30 00:00:00
Date Available	2016-08-30 00:00:00
Creation Date	2016-07-25 16:40:31
Producing Software	Adobe PDF library 10.01
Document Lastmod	2016-07-25 16:40:31
Document Title	QH-912-2二个发射器说明书(3) (1)
Document Creator	Adobe Illustrator CS6 (Windows)

WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Model NO: QH-912-2
Front Door and Back Door Door Chime
(2) Hanging Hole
(5) Push Button
(8) Standby holes for screws
(3) Speaker
(6) Decoration only
(9) Interface
Accessories List
● 2 x Transmitters
● 2 x Double-sided adhesive
Pictures for Accessories:
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, 2xAA 1.5V size batteries, fixing screws and wall plugs. All of these are not supplied
with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
BatteryBattery Installation
Transmitter Unit
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter ( by pushing in the interface located at the bottom with a flat screw driver )
and place the battery. Please be well noted with the correct battery polarity. To replace a new battery,
operate in the same way.
Receiver
Transmitter
CR2032 Battery
Double-side
adhesive
Instruction Manual
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from the back cover, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
Note: This door chime kit is designed mainly for front door and back door use. Please mount one
transmitter at the front door and one at the back door. Of course you can mount the two
transmitters anywhere according to your exact need.
(6)
(9)
(4)
Receiver back side
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
(5)
(8)
Receiver front side
Wall Mount
(7)
(2)
(3)
Receiver
CR2032 3V
Lithium Battery
Names for Parts
(1)
2x1.5V AA
Alkaline Battery
Notes before Installation
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
The door chime kit comes with:
● 1 x Receiver
● 2 x CR2032 Battery
● 1 x Instruction Manual
(1) Melody Selector
(4) Battery Cover
(7) Front cover and back cover hook
Transmitter front
cover outside
Transmitter back
cover inside
Receiver Unit
Remove the battery cover and insert 2×AA 1.5V batteries (not included); Ensure battery polarity
matches the internal markings.
Receiver Unit
Specification
Fix a screw on the wall. Then hang the Receiver by the hole at the back
of the unit. Avoid positioning on UPVC Frames, above heat sources
(e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it is
within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Different Melodies for the Two Transmitters
There are two built-in melodies with the Receiver. The Receiver will sound with different melodies
to response to different signals sent from the two Transmitters. As a reminder, you can not select
the two built-in melodies.
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
1. Flat batteries in either Transmitter or Receivers-change the batteries.
2. Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
3. Units are out of range-Operate the Receiver within the operation range.
● Battery Voltage：Receiver: DC3V(AA1.5Vx2)
● transmitter: DC3V( CR2032)
● Current for receiver： quiescent current<200UA. working current<150MA
● can use about nine month when sounds about ten times everyday
● Current for transmitter: quiescent current<5UA; Working current: <15MA
● If press ten times a day it can use about one year
● Frequency：433.92MHz
● Receiver Sensitivity：<-110dbm
● transmitter power：<10mw
● Volume grade：>80dbA (testing within 0.5m)
● Modulation type：ASK
● transmitting distance in the open area：150M
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to operate the
equipment.
What is Pre-set Code?
There is a transmitting code between Transmitter and the Receiver. During production,
manufacturer has fixed the code which can not be changed by any user out of the factory.
This means, the Transmitter can only work with the Receiver in the same kit.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Format                          : application/pdf
Title                           : QH-912-2二个发射器说明书(3) (1)
Creator Tool                    : Adobe Illustrator CS6 (Windows)
Create Date                     : 2016:07:25 16:40:31+09:00
Modify Date                     : 2016:07:25 16:40:31+08:00
Metadata Date                   : 2016:07:25 16:40:31+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 244
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 25295 bytes, use -b option to extract)
Document ID                     : xmp.did:395A4D5C1052E6119791B22CDD8F8F40
Instance ID                     : uuid:04fd6dda-ecc0-42ad-8608-431e52ba247b
Original Document ID            : uuid:E3E11FD118E2E211BFD3F6E7842A34AC
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:49a54f67-6ba5-431e-ab33-7b93d9512a83
Derived From Document ID        : xmp.did:01F90309B44CE611B81390778BCE5BDC
Derived From Original Document ID: uuid:E3E11FD118E2E211BFD3F6E7842A34AC
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:D7FD8802834CE6118CDA9D4B0F3784CE, xmp.iid:395A4D5C1052E6119791B22CDD8F8F40
History When                    : 2016:07:18 09:30:32+08:00, 2016:07:25 16:40:22+08:00
History Software Agent          : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows)
History Changed                 : /, /
Startup Profile                 : Print
N Pages                         : 1
Has Visible Transparency        : True
Has Visible Overprint           : False
Max Page Size W                 : 445.500111
Max Page Size H                 : 419.999859
Max Page Size Unit              : Millimeters
Font Name                       : ArialMT, Myriad-Roman, Myriad-Bold, Myriad-BoldItalic, MyriadPro-It, AdobeSongStd-Light
Font Family                     : Arial, Myriad, Myriad, Myriad, Myriad Pro, Adobe 宋体 Std
Font Face                       : Regular, Roman, Bold, Bold Italic, Italic, L
Font Type                       : Open Type, Type 1, Type 1, Type 1, Open Type, Open Type
Font Version                    : Version 3.00, 001.001, 001.001, 001.001, Version 2.062;PS 2.000;hotconv 1.0.57;makeotf.lib2.0.21895, Version 5.010;PS 5.002;hotconv 1.0.57;makeotf.lib2.0.21895
Font Composite                  : False, False, False, False, False, False
Font File Name                  : arial_0.ttf, wmr_____.pfb; wmr_____.pfm, wmb_____.pfb; wmb_____.pfm, wmbi____.pfb; wmbi____.pfm, MyriadPro-It.otf, AdobeSongStd-Light.otf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Colorants Cyan    : 80.000000
Swatch Groups Colorants Magenta : 5.000001
Swatch Groups Colorants Yellow  : 10.000002
Swatch Groups Colorants Black   : 0.000000
Swatch Groups Group Name        : 灰度
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: K=5
Swatch Groups Colorants Mode    : GRAY
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Gray    : 12
Producer                        : Adobe PDF library 10.01
Page Count                      : 1
Creator                         : Adobe Illustrator(R) 16.0
For                             : Administrator,
Bounding Box                    : -211 -299 1054 893
Container Version               : 11
Creator Version                 : 16

EXIF Metadata provided by EXIF.tools