Qiaohua QT-14R Receiver User Manual QT 14
SHENZHEN QIAOHUA INDUSTRIES LIMITED Receiver QT 14
Qiaohua >
Users Manual
WIRELESS REMOTE CONTROL SET INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS ● Read all instructions carefully before using the wireless remote control set. ● Open the package and check the machine for obvious damage. If there seems to be damage discontinue use and contact the distributor. INSTRUCTIONS: ● Use the wireless remtoe control SET with our fog machines only. ● Connect the power cord of fog machine into a power socket. ● Connect the plug of the receiver into the back socket of the fog machine. ● Turn of the fog machine and allow to warm up to operating level (approximately 5 minutes). ● After the fog machine has warmed up the red light on the receiver will light up, alerting you that the fog machine is ready for operation. ● You need to remove the battery’s insulation tab at the back of the transmitter for the first time you use it. ● Press the "ON" button to spray the fog and press the "OFF" button to stop the fog. ● Be sure to keep you fog machine at least 7 3/4 inches (20cm) away from any flammable material. ATTENTION: ● Please 1. Power Cord 2. Receiver Indication Light 3. Transmitter Indication Light 4. OFF Button 5. ON Button 6.Battery Insulation Tab Hole 7.Battery Insulation Tab obey all notices about peration,safey,and repair. Not obeying these notices will damage the unit and may result in electric shock. ● Don't open the case of the wireless transmitter or receiver if you are not a professional electrician. ● Keep clean and remove water. ● Indoor use only. ● If you need to repair the item, please contact distributor or professional repair works. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Avis d’Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio par un appareil numérique de classe B stipulées dans les Règlement sur l’interférence redio d’industrie Canada.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Modify Date : 2014:12:08 14:24:07+08:00 Create Date : 2014:11:27 09:42:29+08:00 Metadata Date : 2014:12:08 14:24:07+08:00 Creator Tool : Adobe Illustrator CS3 Thumbnail Width : 184 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 16983 bytes, use -b option to extract) Format : application/pdf Title : QT-14说明书 Document ID : uuid:474cbcef-f8df-4500-90cf-ea868d82b09c Instance ID : uuid:1987cbc6-a899-4de4-8afb-e1cf1af5c4f2 Producer : Adobe PDF library 10.01 N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 595.279968 Max Page Size H : 841.889954 Max Page Size Unit : Points Font Name : Arial-BoldMT, ArialMT Font Family : Arial, Arial Font Face : Bold, Regular Font Type : Open Type, Open Type Font Version : Version 3.00, Version 3.00 Font Composite : False, False Font File Name : ARIALBD.TTF, ARIAL.TTF Plate Names : Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Page Count : 2 Container Version : 11 Creator Version : 13 Creator : Adobe Illustrator(R) 13.0 For : Administrator, Bounding Box : 0 0 596 842 Image Height : 842 Image Width : 596 Image Size : 596x842 Megapixels : 0.502EXIF Metadata provided by EXIF.tools