Qingdao Haier Robot HXS-G1 Smart Sweeping Robot User Manual User Maunal

Download:
Mirror Download [FCC.gov]
Document ID	3373329
Application ID	V+mvKKbUgpKqcvNhdxd7Sw==
Document Description	User Maunal
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	136.63kB (1707841 bits)
Date Submitted	2017-04-27 00:00:00
Date Available	2017-04-27 00:00:00
Creation Date	2017-10-25 21:35:16
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-25 21:35:16
Document Title	User Maunal
Document Author:	Test

Smart Sweeping Robot
HXS-G1
Table of Contents
1 Important Safety Instructions.......................................................................1
2 Product Components...................................................................................2
2.1 The main machine and accessories.................................................................2
2.2 The main machine......................................................................................3
2.3 Charging station.........................................................................................3
2.4 Dustbin....................................................................................................4
2.5 Water tank...............................................................................................4
2.6 Side brush...............................................................................................4
2.7 Remote control..........................................................................................4
3 Product Operations......................................................................................6
3.1 Quick start guide........................................................................................6
3.2 Start/Pause/Standby mode...........................................................................7
3.3 Plan mode...............................................................................................7
3.4 Cleaning mode..........................................................................................8
3.5 Water tank and mop operation.......................................................................9
4 Product Maintenances................................................................................11
4.1 Cleaning of side brush...............................................................................11
........................................................................11
4.3 Cleaning of sensors and charging poles.........................................................12
4.4 Cleaning of main brush..............................................................................12
4.5 Water tank maintenance.............................................................................13
4.6 Battery replacement..................................................................................13
5 Troubles Shooting.......................................................................................14
6 Product Parameters....................................................................................15
1 Important Safety Instructions
Please read the following safety instructions before using this product to
avoid damage.
Warning! Violation of safety instructions may cause
severe personal casualty and property loss.
Do not put weight on the power cord or
bend the power cord, otherwise may
cause electric shock or ire.
Always use the original charger with
this product, otherwise may cause
product damage, electric shock or ire.
Do not touch the power cord with wet
hand, otherwise may cause electric
shock.
Keep the product away from heat or
inlammables.
Do not touch wheels and brushes when
the product is working and keep your
clothes and hair away from the product
when it is working.
Do not attempt to disassemble or
revise the main machine, otherwise
may cause ire, electric shock or
personal injury.
Attention! Violation of safety instructions may
cause personal injury and product damage.
Make sure the charger plugged in the
socket tightly, otherwise may cause
electric shock, short-circuit, smoke or
ire.
Do not use the product to vacuum
stone, big waste paper, burning
cigarette ends or metals.
Do not stand or sit on the product,
otherwise may cause product damage
or personal injury.
Do not use the product on an easy
falling place such as table or chair to
avoid product damage.
Clear up all fragile, braided fabrics,
glasses or bottles before use it,
otherwise may cause damage.
Do not use the product to vacuum
water or other liquids, otherwise may
cause product damage.
Please take careful of children when
use the product to avoid scaring or
injury.
This product is intended to be an
indoor appliance. Never use it outdoor.
Please switch the product off when you
Do not use it in public commercial
places.
will not use it for a long time.
When people with disabilities (body perception and thinking ability defects) and children
using, need to be operated under the guardian to accompany with product use and get
the related instructions.
2 Product Components
2.1 The main machine and accessories
No.
Name
Quantity
Main machine
1pc
Charging station
1pc
Remote control
1pc
Adapter
1pc
Cleaning brush
1pc
Insturction manual
1pc
Side brush
2pcs
Water tank
1pc
Attention:
Please take actual product shall prevail on the basis of not less than the above accessories.
2 Product Components
2.2 Main machine
10
13
14
11
12
1. Signal receiving
sensor
2. Clean button
3. Bumper
4. Panel
5. Universal wheel
6. Charging poles
7. Battery cover
8. Stair detection
sensor
9. Main brush
10. Dustbin
2.3 Charging station
1.Signal receiver
2.Signal projector
3.Charging poles
4.Indication light
5. Adapter socket
11.Dustbin cover button
12.Charging socket
13. Side brush
14. Drving wheel
2 Product Components
2.4 Dustbin
1.Primary ilter
2.High eficency ilter
3.Dusbin upper cover
4. Dusbin botton cover
2.5 Water tank
1. Water tank button
2. Water inlet cap
3.Air valves
4. Water leakage hole
5. Mop
2.6 Side brush
Please install the side brush according to the color
of the socket of the side brush. Left brush is green
color, and right brush is red color.
2.7 Remote control
The robot is in standby or cleaning mode, press this button to start auto recharging.
1 Press this button to change standby mode from sleep mode (power switch is on).
2 In standby mode, press this button to start cleaning.
2 Product Components
3 In cleaning mode, press this button to stop
cleaning.
4 In plan mode, press this button to conirm
the schedule setting.
5 Press this button to start cleaning when
the robot is recharging on charging station.
Press this button to start random cleaning
mode. The process is zigzag cleaning mode,
ixed cleaning mode, and cleaning mode in
edgewise.
Press direction button to adjust the robot
moving direction.
Press this button for 3 seconds to start time
setting, press again to conirm time setting.
In cleaning mode press this button to start strong suction power cleaning.
Long press this button to start schedule setting, press On/Off button to conirm setting. In the
process of setting, press schedule button to unset. (Before reschedule cleaning, set current
clock time to conirm that the remote control aims at the machine).
In standby or cleaning mode, press this button to start edgewise cleaning mode.
In standby or cleaning mode, press this button to start advanced zigzag cleaning mode.
10
In standby or cleaning mode, press this button to start spot cleaning mode. The robot start
Zigzag cleaning mode automatically after spot cleaning inished.
Attention:
1 Please install 2 AAA/R03(No.7) battery.
2 Please take out battery when you do not use for a long time.
3 Remote control will be in standby mode in a few seconds after use, please press any key to
wake up it.
3 Product operations
3.1 Quick start guide
1.Place charge
Place charger, connect the adapter and
power, and the power light on the charger
will stay lit. Position the charger against
the wall, and remove all obstacles about 1
or 2 meters ahead of the charger.
2. Power Switch
Open the power switch at the bottom of the machine, host keypad led is lit, the machine enters
standby mode..
3. Main machine sweep button
Turn on the power switch of the product, and press directly the sweep button on the panel, it will
begin with a zigzag path cleaning.
4.Product charging
Power
There are two methods of charging.
1 Plug the power adapter directly to the
machine and the other end is plugged in
the power.
Robot
Adapter
2 When the charge is lower than 20%, the
machine will automatically start looking for
recharge stand, or press the recharge
button on the remote control to return
the automatic charger. Automatic
recharge-sensing distance as in the
charging a RADIUS 4m, please ensure
that the charger is powered and obstacle
location as little as possible, otherwise it
could not ind the charger.
Attention:
1 When charging, make sure the power switch is on.
2 using the charger stand will interrupt the charging and start the cleaning, so please do not
make this operation when using thedirect charge.
3 Product operations
3 Charging the machine 6 hours for the irst time.
4 When charging, the cleaning button blinks, and when fully charged, the cleaning button stops
blinking, and lit permanently.
5 Please switch the main machine off when long time no use.
3.2 Pause/Standby mode
1. This model operation process: sleep mode>Standby mode>Cleaning
mode
1 Sleep mode: power switch is on, CLEAN button light is off, the robot does not work.
2 Standby mode: power switch is on, CLEAN button light is on, the robot does not work.
3 Cleaning mode: the robot is cleaning, CLEAN button light is off.
2.Start
1 Please turn on the switch at the bottom of the
machine.
2 Press sweep button on the machine or on
the remote control to automatically start the
machine to work.
Attention:
When the robot is in sleep mode, press CLEAN
button on the main machine to wake it up, press
again to start cleaning.
3.Standby mode
Standby mode refers to the machine switching from working status to static status. Press the
sweep button on the machine or switch button on the remote control to operate.
4.Sleep mode
In standby mode without any operation the machine will enter into standby mode after 2
minutes, and the machine is in static status and the button indicator light is off.
3.3 Plan mode
Under the plan mode, the machine can work at a preset time.
1.Set the remote controller clock time
1 Long press the clock button in the remote controller for 3 seconds, and set a speciic time
according to “up, down, left and right” direction button.
2 Press the clock button once again to save the setting.
2.Set the pre-scheduled cleaning time
1 Point the remote controller at the machine (the machine is in standby status).
3 Product operations
2 Long press the “plan” button in the remote controller for 3 seconds into the plan mode, and set
a speciic time according to “up, down, left and right” direction button.
3 Press the on/off button to save the settings, and to cancel the plan, press the “plan” button
again (During the operation, the machine is always on the standby status.)
Attention:
1 Set clock for your remote control before cleaning, the time settings are using real time.
2 Replace the remote control batteries, reset the appointment.
3 This machine uses real time for an appointment. If power is off, you will need to make an
appointment.
4 Make an appointment for each half hour, clock settings are in minutes.
3.4 Clean mode
1.Automatic clean
1 Press the clean button on the machine directly
into the zigzag cleaning mode, if not switching,
the operating mode remains unchanged.
2 Press automatic button on the remote controller
for random cleaning, and the process is the
zigzag cleaning mode, ixed cleaning mode and
edgewise cleaning model.
Attention:
Machine in any cleaning mode, press the remote control "on/off" button or sweep button on the
machine to stop working.
2.Spot cleaning
1 Place machine in clean area, press the remote
control's "SPOT " button on the machine to start
with the placement point spiral sweep.
Attention:
2 After the spot cleaning is completed, the
machine will automatically enter zigzag cleaning
mode.
3 Remote control on the machine’s instructions
is required to point at the machine in order to
operate successfully.
3 Product operations
3.Edge cleaning
1 Press edge cleaning button on remote control
to start edge cleaning mode, the robot will start
edge cleaning.
2 In auto cleaning mode, the robot also may start
edge cleaning.
4.Advanced zigzag cleaning
Press zigzag cleaning button on remote control
to start advanced zigzag cleaning.
Attention:
In any mode, press this button to start
strong suction power cleaning.
3.5 Water tank and mop operation
1.Filling water into water tank
1 Open water inlet cap.
2 Fill in water and cover the cap. Water tank capacity is 260ml(appr.).
3 Check whether the tank bottom outlet wool column drops (not drops is normal).
4 After the check, MOP stick irmly on the water bottom, put the blue Flannel into the machine
facing the ground.
5 Put the tank into the machine, start the machine, and water enters into the mop through wool
column, water stopped dripping out of the tank when the machine stops. Pour water out if the
machine stops working for a long time.
3 Product operations
2 Installation of water tank
MOP chassis is mounted on the machine, and when installed, please aim at the tanks ixed
jacks.
Attention
1 Please remove the water tank when injecting
water, and do not inject with complete machine.
2 Please remove water drops when installation
of water tank.
3 Mop shall not be too wet, and wring to prevent
tire slippage.
10
4 Product Maintenances
4.1 Cleaning of side brush
Side brush can be removed and clean by water.
Please dry them completely before second use.
If side brushes damaged, please replace them.
Attention:
When replace side brush, please pay attention
to the L and R position and color.
4.2 Cleaning of dustbin and ilter
1 Press PUSH button on dustbin, remove the dustbin.
2 Open dustbin bottom cover.
3 Hold primary ilter and pull out, then pull out high eficiency ilter.
4 Pour out trash into trash bin.
5 Clean dustbin, high eficiency ilter and primary ilter completely. High eficiency ilter lifetime is
6 months.
6 Please install them correctly before second use.
Attention
1 Please clean the dustbin after each use.
2 Parts washed by water, do not expose to sun. Please install them after drying completely.
3 Please do not use the robot when primary ilter and high eficiency ilter are damaged to avoid
motor damage. Please replace new ilters before use.
4 High eficiency ilter cannot be washed by water.
11
4 Product Maintenances
4.3 Cleaning of sensors and charging poles
1 Clean sensors and charging poles on robot bottom by using soft cloth.
2 Clean charging poles on charging station by using soft cloth.
Charging contactor
Sensor
Sensor
Charging contactor
4.4 Cleaning of main brush
1 Press the locker, open main brush cover.
2 Hold one end of main brush, take out. Install another end of main brush irst when installation
after cleaning.
3 Clean the hair and dirt by using a cleaning brush. Please make sure that do not lose the
rubber.
4 Install the main brush and cover after cleaning.
Attention
All maintenance must be done after dustbin removed.
12
4 Product Maintenances
4.5 Water tank maintenance
1 When the mop need to be cleaned, remove
the mop irst, clean dirt irst then wash by water.
2 Air valve do not need to be maintained when
normal use. Clean it when water leakage is
abnormal (the power switch is off).
3 Take out air valve components, check and
clean, then install correctly.
Attention: Air valve components include: air
valve frame air valve(rubber).
Do not miss or damage when maintenance.
Air valve assembly
Air valve cover
Air valve seat
Mop
4.6 Battery replacement
1 Open the battery cover by using a screw driver.
2 Hold the insulation cloth and pull out the battery.
3 Detach the battery from the main machine.
4 Install new battery. Make sure the side with
words up.
5 Connect the battery with main machine.
6 Lock the battery cover.
7 Turn on the robot to check.
Attention:
Battery
1 Do not use unapproved battery to avoid damage.
2 Please charge for 6 hour after new battery
changed.
3 Keep the old battery for recycling.
13
5 Trouble shooting
No.
Problems
Solution
The robot keeps
moving backwards
1 Avoid working in high light intensity environments.
2 Avoid working on deep dark carpets.
3 Clean the stair detection sensors by using a soft
cloth.
4 Check the bumper and clean.
The robot do not work
1 Turn on the power switch button.
2 Check the battery capacity, and charge the robot.
Check again after full charging.
The robot do not
recharge automatically
1 Make sure the indication light on charging station is
on.
2 Check if there are obstacles between robot and
charging station.
3 When low battery, please charge the robot by using
adapter.
The robot cannot be
recharged
1 Please use approved adapter and make sure
adapter plugged.
2 When the robot is damaged, please do not use.
Contact after sales.
Remote control do not
work
1 Check the remote control battery; Check the signal
sensor on the robot clean it.
14
6 Product Parameters
Size
320*320*85mm
Net Weight
3.2kg
Working voltage
14.8V
Input voltage
19V
Input current
1.0A
Dustbin capacity
400mL
One time charging time
4-6h
90-120min
One time cleaning time
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To comply with FCC RF exposure compliance requirements,this grant
isapplicable to only mobile configurations. The antennas used for this
transmittermust be installed to provide a separation distance of at least 20 cm
from allpersons and must not be co-located or operating in conjunction with any
otherantenna or transmitter.
15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:9f30095f-9c30-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:08 19:31:43Z
Create Date                     : 2017:07:08 19:31:43Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:9f30095f-9c30-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled

EXIF Metadata provided by EXIF.tools