Qingdao Yeelink Information Technology YLDD04YL Yeelight Lightstrip Plus User Manual Pitaya plus 201800205
Qingdao Yeelink Information Technology Co., Ltd. Yeelight Lightstrip Plus Pitaya plus 201800205
User Manual
480mm(±0.5)
Product Introduction
Installation Steps
Intelligent Control
1. Search Yeelight in an app store or scan the QR code below to download the Yeelight App.
Lightstrip (80in)
Controller
Connector
Data cable (60in)
2. Turn on the lightstrip. Open the app and operate the lightstrip in accordance with the instructions provided
Adapter*
in the app.
* Make sure that the Wi-Fi network is available and is able to access the Internet properly.
Power cable
Clean the installation surface.
Plug into the adapter, rotate
by 45 degrees clockwise and
snap into place.
Yeelight Lightstrip Plus User Manual
Stick to the installation surface.
Please read this manual carefully before using the product
Factory Reset
Connect and plug in the power supply.
Tap to turn on the lightstrip, tap again to turn off
the lightstrip, and press to select your desired color.
* The real object prevails.
Cut off the adapter power. Press the power button and reconnect to the power supply. Hold the button for
five seconds until the lightstrip displays red, green, and blue circulating lights, and then release the button.
The reset is complete when the light turns yellow.
* Perform the factory reset and connect the lightstrip again every time you use a new Wi-Fi network.
Lightstrip Plus Extension
(40in each)
120mm(±0.5)
* Need to purchase additionally.
To use the extendible feature of lightstrip, purchase Yeelight Lightstrip Plus Extension. Match the end of original
lightstrip with the connection port of Lightstrip Plus Extension and put into fastener. Be sure each strip is tightly
connected to the other before continuing to mount the next strip.
Speci cations
Warning
Model No.: YLDD04YL
1. Before using this product, please make sure that your voltage is appropriate for the working voltage of this
product. Using this product with a voltage other than the one specified may damage the product and cause
safety hazards.
Frequency Bands: 2400MHz-2483.5MHz
Rated Input: 100-240V~50/60Hz 0.17A (80in) 100-240V~50/60Hz 0.6A (400in)
2. For indoor use only.
Rated Power: 7.5W (80in) 26.6W (400in)
3. To prevent early product failure, product should only be installed in operating environments ranging
between:10℉ to 104℉(-10℃ to +40℃).
Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz
4. Do not use where directly exposed to water.
System Requirements: Android 4.4 or later, iOS 8.0 or later
(1) Reorient or relocate the receiving antenna.
6. The external flexible cable or cord of this luminaire cannot be replaced. If the cord is damaged, the luminaire
shall be destroyed.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
8. Do not disassemble the product, as the light diodes can cause damage to the eyes.
9. This product is not a toy and should not be stored or left in locations accessible to young children.
10. Max interconnected 400in.
11. Do not bend the LED inside the lightstrip in more than 90 degrees to avoid damaging the product.
12. Do not connect the lightstrip to the power supply when it is in the package.
Color Adjustment
Brightness Control
One-button Operation
Mobile Control
13. Do not interconnect parts of this lighting chain with parts of another manufacturer’s lighting chain.
14. Interconnection shall be made only by the use of the supplied connectors. Any open ends must be
sealed-off before use.
Manufacturer: Qingdao Yeelink Information Technology Co., Ltd.
>24?@2.'(A3.+*24'(B@2.*4.+
Extendible
Timer Switch
Scene Transformation
Firmware Upgrade
Website: www.yeelight.com
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.This equipment has been tested and found to
Customer Service Email Address: support@yeelight.com
(2) Increase the separation between the equipment and receiver.
(4) Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
EU Declaration of Conformity
We Qingdao Yeelink Information Technology Co.,Ltd., hereby, declares that this equipment is in compliance
with the applicable Directives and European Norms, and amendments.
WEEE Disposal and Recycling
Correct Disposal of this product. This marking indicates that this product should not be disposal with other
household wastes throughout the EU.
FCC Compliance Statement
Address: !"#$%&'(%)*+,%'(-./01.2/34.2)(-..452/34.(6217'("8(90:;2.<03:3(=*,'(
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
5. Regularly check the cord, the power supply and all other parts for damage. If any part is damaged, the
product should not be used.
7. The light source of this product is non-changeable light diodes (LED).
Product Features
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, rescycle it
responsibly to promote the sustainable reuse of material resources.
To return your used device, please use the return and collection systems or contact the retailer where
the product was purchased. They can take this product for environmental safe recycling.
%.$??@A$BCD
产品介绍
使用方法
恢复出厂设置
断开适配器电源,按住开关键并重新接通电源,保持5秒,至灯带开始红绿蓝流光时可松手,当指示灯变为
黄色时,即重置成功。
灯带(2m)
控制器
连接器
数据线(1.5m)
适配器
电源线(1.5m)
Yeelight 彩光灯带(延长版)使用说明书
* 当灯带在新的网络环境使用时,需恢复出厂设置,再重新进行网络连接。
将插头插入电源适配器,顺
时针旋转45' ,听到“嗒”声
后安装完成。
清理安装粘贴表面。
将电源适配器插入插座。
轻触“ ”打开灯带,再次轻触
“ ”关闭灯带,按住“ ”选
择自己喜欢的颜色。
粘贴在安装表面。
安全注意事项
1. 使用前请确认电压是否符合本产品的工作电压,使用不适当的电压可能会损坏产品并带来安全隐患;
2. 此灯具的光源是不可替换的,当光源到其寿终时,应替换整个灯具;
3. 灯带在工作中会产生热量,请保持周围空气对流,以便散热;
4. 请勿将灯带内灯珠元件位置弯折超过九十度,以免损坏产品;
5. 请勿在水源附近使用,以免产品进水导致产品损坏或其他意外情况发生;
6. 请勿存放于儿童可触及的地方,儿童需在家长的照看下使用本产品;
7. 当灯具在包装盒里时,不要将其与电源连接;
8. 灯带最大可延长至10米;
9.只能在室内使用。
使用产品前请仔细阅读本说明书,并妥善保管
智能控制
若希望使用灯带延长功能,请购买
Yeelight 彩光灯带(1米延长包)。 轻
扣延长版灯带与原灯带的延伸接口
端,将扣合的两端口放入卡扣中,
扣紧卡扣,即完成拼接。
1. 扫描二维码或在应用商店下载Yeelight移动客户端;
2. 确保灯带为开启状态,开启应用,并按照应用内的指导进行操作。
产品中有害物质的名称及含量
部件名称
有害物质
铅(Pb) 汞(Hg) 镉(Cd) 六价铬(Cr(VI)) 多溴联苯(PBB) 多溴二苯醚(PBDE)
灯 带
控制器
* 请确保Wi-Fi网络可用,并且可以正常访问互联网。
适配器
线 材
灯带(1m 延长包)
!"#$$%'()
本产品兼容米家智能平台,
可通过“米家”APP操控,
支持MIUI系统,可与其他米
家智能平台产品互联互通。
*需另外购买
基本参数
产品保修说明
产品型号:YLDD04YL
频
功率因数:0.35(2m)
电源输入:100-240V~50/60Hz 0.17A (2m)
0.4(10m)
100-240V~50/60Hz 0.6A (10m)
无线连接:Wi-Fi IEEE 802.11 b/g/n 2.4GHz
支持平台:Android 4.4 & iOS 8.0 及以上版本
段:2400MHz-2483.5MHz
额定功率:7.5W(48颗×0.087W/LED模块) (2m)
26.6W(240颗×0.087W/LED模块) (10m)
本表格依据SJ/T 11364的规定编制。
表示该有害物质在该部件所有均质材料中的含量在GB/T $%5&$规定的限量要求以下。
表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。
Yeelight 彩光灯带(延长版)三包凭证
Yeelight 彩光灯带 (延长版)产品售后服务严格依据《中华人民共和国消费者权益保护法》、《中华人民共
和国产品质量法》实行售后三包服务,服务内容如下:
1. 自您签收次日起7日内,本产品出现《产品性能故障表》所列性能故障的情况,经Yeelight售后服务中心检
测确定,可免费享受退货或换货服务;
2. 自您签收次日起8日-15日内,本产品出现《产品性能故障表》所列性能故障的情况,经由Yeelight售后服
务中心检测确定,可免费享受换货或者维修服务;
3. 自您签收次日起12个月内,本产品出现《产品性能故障表》所列性能故障的情况,经由Yeelight售后服务
中心检测确定,可免费享受维修服务。
非保修条例
产品特点
色彩调节
1. 未经授权的维修、误用、碰撞、疏忽、滥用、进液、事故、改动,或撕毁、涂改、标贴、防伪标记;
2. 已超过三包有效期;
3. 因不可抗力造成的损坏;
4. 不符合《产品性能故障表》所列性能故障的情况;
5. 因人为原因导致产品及其配件产生《产品性能故障表》所列性能故障。如使用调光器、使用非额定电压、
使用非标配适配器、在非规定的环境下使用等,导致的产品性能故障情况。
亮度调节
一键操作
手机控制
产品性能故障表
名称
灯带
欢迎访问Yeelight售后服务网页 www.yeelight.com
或拨打Yeelight服务电话:400-619-7969 咨询更多售后问题
灯不亮
灯光颜色缺失
无法搜索到灯带
可延长
场景变换
定时开关
固件升级
控制器
按键功能失效
适配器
无法正常给灯带供电
复位失效
制造商:青岛亿联客信息技术有限公司
地址:青岛市崂山区科苑纬一路1号青岛国际创新园B座10层B4
性能故障
Yeelight 彩光灯带(延长版)三包凭证
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Modify Date : 2018:06:20 14:03:34+08:00 Create Date : 2018:05:20 21:45:34Z Metadata Date : 2018:06:20 14:03:34+08:00 Creator Tool : Adobe Illustrator CC 2017 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 192 Thumbnail Format : JPEG Thumbnail Image : (Binary data 13540 bytes, use -b option to extract) Instance ID : uuid:8d0b14df-a11a-4e7b-bc97-59ab2fb8ce16 Rendition Class : proof:pdf Document ID : xmp.did:4dd4105f-66c1-4719-a3fc-afc8ed876079 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf Derived From Document ID : xmp.did:bef89a9c-4dad-4d77-9e64-49c353a5ddce Derived From Instance ID : uuid:4a098bde-f462-4545-bc7e-ce077642ba46 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 History Software Agent : Adobe Illustrator CS6 (Windows), Adobe Illustrator CC 2017 (Macintosh) History Changed : /, / History When : 2017:08:15 16:51:19+08:00, 2018:05:21 05:34:08+08:00 History Instance ID : xmp.iid:F4303F6A5E81E71192C9C0750CC78985, xmp.iid:4dd4105f-66c1-4719-a3fc-afc8ed876079 History Action : saved, saved N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 1185.954226 Max Page Size H : 886.900989 Max Page Size Unit : Millimeters Font Name : SimSun, AdobeSongStd-Light, FZLTZHK--GBK1-0, FZLTZHUNHK--GBK1-0, FZLTXHK, FZYOUH_503L--GB1-4, FZYOUH_504L--GB1-4, FZYOUH_506L--GB1-4, Helvetica-Light, HelveticaNeue-Light, HelveticaNeueLTStd-Lt, HelveticaNeueLTStd-Roman Font Family : 宋体, Adobe 宋体 Std, 方正兰亭中黑_GBK, 方正兰亭准黑_GBK, 方正兰亭细黑_GBK, 方正悠黑, 方正悠黑, 方正悠黑, Helvetica, Helvetica Neue, Helvetica Neue LT Std, Helvetica Neue LT Std Font Face : Regular, L, Regular, Regular, Regular, 503L, 504L, 506L, Light, Light, 45 Light, 55 Roman Font Type : Open Type, Open Type, TrueType, TrueType, TrueType, TrueType, TrueType, TrueType, TrueType, TrueType, Open Type, Open Type Font Version : Version 5.04, Version 5.017;PS 5.002;hotconv 1.0.67;makeotf.lib2.5.33168, 1.00, 1.00, Version 1.00, 2.00, 2.00, 2.00, 10.0d4e1, 10.0d40e1, Version 2.035;PS 002.000;hotconv 1.0.51;makeotf.lib2.0.18671, Version 2.020;PS 002.000;hotconv 1.0.50;makeotf.lib2.0.16970 Font Composite : False, False, False, False, False, False, False, False, False, False, False, False Font File Name : SimSun.ttf, AdobeSongStd-Light.otf, 方正兰亭中黑_GBK.TTF, 方正兰亭准黑_GBK.TTF, 兰亭细黑 GBK.TTF, 方正悠黑_503L.ttf, 方正悠黑_504L.ttf, 方正悠黑_506L.ttf, Helvetica.dfont, HelveticaNeue.dfont, HelveticaNeueLTStd-Lt.otf, HelveticaNeueLTStd-Roman.otf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE Cool Gray 11 C Swatch Group Name : 默认色板组 Swatch Group Type : 0 Swatch Colorant Swatch Name : PANTONE Cool Gray 11 C Swatch Colorant Type : SPOT Swatch Colorant Tint : 100.000000 Swatch Colorant Mode : Lab Swatch Colorant L : 36.470589 Swatch Colorant A : 0 Swatch Colorant B : -3 Format : application/pdf Title : Pitaya plus 中英文版 201800205 Startup Profile : Print Producer : Mac OS X 10.11.4 Quartz PDFContext Page Count : 1 Creator : Adobe Illustrator(R) 17.0 For : songsong, Bounding Box : 0 0 3362 2515 Container Version : 11 Creator Version : 21 Image Height : 2515 Image Width : 3362 Image Size : 3362x2515 Megapixels : 8.5EXIF Metadata provided by EXIF.tools