Quanta Computer EY5 Pi SOLO User Manual quick start guide EN 20161018
Quanta Computer Inc Pi SOLO quick start guide EN 20161018
TempConfidential_[STC]quick start guide
Quick Start Guide
www.pi-solo.com
Freedom of Perspective
The world's first immersive lifestyle camera
for smartphone.
Important safety information
1. Using or connecting non-genuine products might shorten the lifespan of the
product, or cause explosions. Doing so might also damage the product and
further void the warranty.
2. Do not disassemble the product or allow any object to collide with the
product. This may cause electric shocks, short-circuit or cause a fire.
3. Please use this product between temperature conditions 0℃ to 35℃. Avoid
exposing the product to direct sunlight for extended periods of times. This may
cause damages to the product or explosions.
4. Please wipe this product with soft cloth. Keep the camera in the storage bag
when not in use.
5. Do not connect or insert conductive material (metal components or pencil
led etc.) into the connector.
6. Do not cover the product with a blanket when in use.
7. The product might heat up after long-term use. Avoid touching the product
when it heats up as doing so may result in low temperature burns.
8. The camera might heat up when recording videos for extended periods of
times. The camera may cease operation in order to prevent damages due to
high temperatures.
9. Do not discard the product as household waste. Doing so may cause fire or
harm the environment.
Limited Warranty
Contact us
One year standard limited warranty is provided for this product starting
from the date of sale, guaranteeing that there are no material, manual
or design flaws for the hardware and accessories included in the
original product package. This warranty is not applicable to (1) batteries
and other consumable components, unless there is flaw in the material
itself; (2) cosmetic damages, including but not limited to scratches and
dents on the surface; (3) damages resulted from using with another
product or with non-genuine accessories. (4) Damages caused by
external factors such as accidents, improper use or improper handling.
Or (5) Removed, incomplete or unidentifiable product serial number
label. Please visit our website at www.pi-solo.com for more information.
Micro SD card installation
Remark: Supports Class10 and above, FAT32 format and a
maximum capacity of 64GB.
Downloading the
Pi-SOLO application program
Android ios
Remark: The serial number printed at the bottom of the
camera is the wireless network name and password.
Wireless network name (SSID): EY5XW1634SSS
Password: XW1634SSS
EY5XW1634SSS
Product components
Pi SOLO Camera Smartphone holder
Lens cap and wire
Micro USB to Micro USB cable
B
B
Micro USB to Type C USB cable
B
Micro USB to Type A USB cable
B
Quick Start Guide
Quick Start Guide
www.pisolo.com
Protective pouch
Smartphone holder tripod extender
Camera operation
instructions
Power button (shutter)
• Press the power button when the camera
is off to turn it on
• Press the power button to take photos
once the camera is on
• Press and hold down the power button for
two seconds to switch to recording mode;
release the power button before holding it
down for five seconds to start recording
• If the power button is pressed and held
down for over five seconds, the camera will
automatically enter the shutdown process
Power indicator
• Once the power is turned on, the power
button will remain green constantly
• While powering on, the power button will
flash green
• When there is less than 20% power
remaining, the power button will remain
yellow constantly
• When there is less than 10% power
remaining, the power button will remain red
constantly
• When there is less than 5% power
remaining, the power button will flash red
Recording indicator /
countdown indicator
Memory card slot and
Micro USB port
Tripod mounting hole
SAFETY STATEMENT
CE Marking
This device has been tested to and conforms to the regulatory
requirements of the European Union and has attained CE Marking. The
CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark
applies to products regulated by certain European health, safety and environmental
protection legislation. The CE Mark is obligatory for products it applies to: the
manufacturer affixes the marking in order to be allowed to sell his product in the European
market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to
attain CE Marking.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a
product. Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings
are voluntary.
Marking: The product shall bear the CE mark
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or
Canada, Industry Canada (IC)
Notices
This Class B digital apparatus complies with Canadian ICES-003
and RSS-247.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that
may cause undesired operation of the device. Exposure of humans to RF fields (RSS-102)
The computers employ low gain integral antennas that do not emit RF field in excess of Health
Canada limits for the general
population; consult Safety Code 6, obtainable from Health Canada's Web site at http://www.hc-sc.gc.-
ca/
The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of
the RF exposure requirement
regarding IC RSS-102, Issue 5.
Cet appareil numérique de classe B est conforme à la norme NMB-003 et RSS-247.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts
de licence.L'exploitationest autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doitaccepter tout brouillage adioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Conformité des appareils de radiocommunication aux limites d'exposition humaine aux radiofréquences
(CNR-102)
L'ordinateur utilise des antennes intégrales à faible gain qui n'émettent pas un champ électromag-
nétique supérieur aux normes
imposées par Santé Canada pour la population. Consultez le Code de sécurité 6 sur le site Internet
de Santé Canada à
l'adresse suivante : http://www.hc-sc.gc.ca/
L'énergie émise par les antennes reliées aux cartes sans fil respecte la limite d'exposition
aux radiofréquences telle que définie
par Industrie Canada dans ldu document CNR-102, version 5.
more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
FCC RF Radiation Exposure Statement:
This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
The exposure standard for wireless device employs a unit of measurement known as the Specific
Absorption Rate, or SAR.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Please pair and connect your Pi-Solo with the APP for
the correct date/time stamp.
写真を撮る前に、撮影時間を補正するためにAPPを接続します
Veuillez associer votre Pi-Solo à l'APP pour l'horodatage correct.
拍攝照片前，請先連接 APP 以校正拍照時間