Quanta Computer LM17B LTE M.2 Card User Manual Regulatory

Download:
Mirror Download [FCC.gov]
Document ID	2537181
Application ID	TrrhYkkrZgv8MesmbzjUEw==
Document Description	User Manual Regulatory
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.25kB (103065 bits)
Date Submitted	2015-02-17 00:00:00
Date Available	2015-08-16 00:00:00
Creation Date	2017-10-18 20:36:00
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-18 20:36:00
Document Title	User Manual Regulatory

Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as show in
this manual.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.
End Product Labeling
When the module is installed in the host device, the FCC ID label must be visible through a window
on the final device or it must be visible when an access panel, door or cover is easily re-moved. If
not, a second label must be placed on the outside of the final device that contains the following text:
“Contains FCC ID: HFS-LM17B”
The grantee's FCC ID can be used only when all FCC compliance requirements are met.
This device is intended only for OEM integrators under the following conditions:
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
(3) To comply with FCC regulations limiting both maximum RF output power and human exposure to
RF radiation, the maximum antenna gain including cable loss in a mobile exposure condition must
not exceed:
Standalone Condition:
。 9.5 dBi in 1900 MHz Band
。 6.5 dBi in 1700 MHz Band
。 10.5 dBi in 700 MHz Band
Assuming collocated with an ordinary WLAN transmitter with 5 dBi antenna gain
。 9.5 dBi in 1900 MHz Band
。 6.5 dBi in 1700 MHz Band
。 7.0 dBi in 700 MHz Band
In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid and
the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Create Date                     : 2015:01:08 17:00:16+08:00
Modify Date                     : 2015:02:10 18:15:08+08:00
Metadata Date                   : 2015:02:10 18:15:08+08:00
Producer                        : doPDF Ver 7.2 Build 376 (Windows 7 Enterprise Edition - Version: 6.1.7600 (x86))
Format                          : application/pdf
Document ID                     : uuid:505dea84-f285-4d8f-8cea-c2dda75aeb66
Instance ID                     : uuid:bba5dc6b-3a97-448e-9619-d2eb35185758
Page Layout                     : OneColumn
Page Mode                       : UseNone
Page Count                      : 2

EXIF Metadata provided by EXIF.tools