Quanta Computer QTAIG1 Router User Manual TempConfidential Backpack Installation UsageGuide 3

Quanta Computer Inc Router TempConfidential Backpack Installation UsageGuide 3

Contents

TempConfidential_Backpack_Installation_UsageGuide 3

Step 3: Set up the 4G LTE Mount for Canary Flex™ in the Canary app.Visit canary.is/app on your iOS or Android device for instructions on setting up your 4G LTE Mount with your Canary Flex. Step 4: Place your Canary Flex™ inside the main unit. The magnet inside of the main unit will grab the Canary Flex as you place it inside of your unit. Tilt the Canary Flex into place. You will need access to the button on the back of the Canary Flex during the setup process for the 4G LTE Mount, so do not place your Canary Flex into the main unit until you have completed the setup process for the 4G LTE Mount in the Canary appOnce the device is placed in the mount, you will be able to charge both the Canary Flex and the 4G LTE Mount with the same plugWelcome to your 4G LTE Mount for Canary Flex™—connected by Verizon WirelessInstallation GuideIn the box1 4G LTE Mount for Canary Flex1 AC power adapter with 13 ft cable1 hex toolVerizon Wireless 4G LTE SIM card (pre-installed) 5 wall mounting screws5 wall mounting anchors2 cover screws1 security screw1 baseplateWhat you’ll needPhillips screwdriverDrill Step 5: Join the cover to the main unit. Push the cover into place over the Canary Flex. Use the hex tool to screw the cover screws to the cover to the main unit--one screw on the top tab, another on the bottom.Please note, the smaller ‘tab’ goes on the bottom, and the larger one (with speaker holes) goes on top. Top BottomInstallation instructionsIMPORTANT: In order to set up your 4G LTE Mount for Canary Flex™, you will need to install the Canary app, available from canary.is/app on your iOS or Android device. Step 1: Remove the cover from the main unit. Please note the cover comes attached to the main unit, without screws. To remove, pinch the top and bottom of the unit and the cover will slide o easily. Step 2: Charge the 4G LTE MountPlug the included AC power adapter for the 4G LTE Mount into any 100-240V wall outlet to charge the long-life lithium-ion battery. It will take approximately 7-8 hours for your 4G LTE Mount to fully charge when it is powered o (longer if it’s in use).Overview of componentsCover ScrewSpeaker HoleFoot/baseFront LEDMiddle LEDRear LEDSIM Card DoorActiviation QR CodeCharging connectorStep 6: Install the baseplate. For installation onto a wall or other vertical surface: Ensure that the baseplate hooks are facing up. Hold the baseplate against the installation surface (for example, your wall or fence) and use a pencil to make three marks through the three holes in the back of the baseplate. On the pencil marks, drill three pilot holes into the installation surface. Note: If wall anchors are required for your installation (drywall, brick, concrete), use a 1/4” drill bit to drill pilot holes in the installation surface. If wall anchors are not required for your installation (wood), use a 3/32” drill bit to drill pilot holes in the installation surface. Align the baseplate holes with the pilot holes in the installation surface and install the provided wall anchors (optional) and wall mounting screws. FPO FPOFPO FPOFPO FPOFPO FPOFPOFPOFPOThis side upInstallation and Usage Guide
For use on a tabletop or other flat surface: Baseplate usage is optional--you may simply place the device on the flat surface. If additional stability and security are desired, install the device into the flat surface by following the installation steps described above. Step 7: Choose your orientation. Two options are available: 1) for use with the AC power adapter, and 2) for wire-free use. Step 8: Route the cable if opting for plugged in use. If planning to use the device with outlet power, route the cable through the channel in the ‘foot’ of the device prior to attaching the 4G LTE Mount to the baseplate. Step 9: Slide the foot of the 4G LTE Mount into the baseplate. Align the 4G LTE Mount foot with the top of the baseplate, and slide it into place. Power Button OperationPower OnPower OFactory ResetActionsPress and hold power buttonPress and hold power button for 5 secondsWhile 4G LTE Mount is on, press and hold power button for 15 secondsStep 10: Secure the 4G LTE Mount foot to the baseplate and complete installation. Use the provided hex tool to tighten the security screw and secure the unit firmly to the baseplate.Step 11: Adjust the angle.Adjust the angle of your 4G LTE Mount by rotating the device until it’s in the desired position. Usage tipsMonitoring data usageYou can monitor your 4G LTE Mount data usage and set up usage alerts through your My Verizon account. Monitoring battery lifeView battery level in the Canary app to check the current battery level and know when to recharge. Tightening the ball jointYou can tighten the ball joint in your device if you notice any loosening over time. Remove the cover from your 4G LTE Mount by unscrewing the two cover screws holding it in place. Take the Canary Flex out of the 4G LTE Mount. You will see a screw located in the back of the main unit, towards the base. Use your hex tool to tighten this screw. Place the Canary Flex back into the 4G LTE Mount, and reassemble. Removing the 4G LTE SIM cardYour SIM card is pre-installed. To remove the SIM card from your 4G LTE Mount, open the rubber door under the Activation QR Code with your fingernail. Press on the SIM card once the door is opened, then pull the card out. Power Button Usage, and LED Indicators Charging Status4G LTE Mount is powering on4G LTE Mount is on and plugged into AC power adapter4G LTE Mount is running on battery power and battery level is 20% or greater4G LTE Mount is running on battery power and battery level is less than 20%4G LTE Mount is powered oCharging Status4G LTE Mount has an Internet connection4G LTE Mount is powering on4G LTE Mount is on but has no Internet connection4G LTE Mount has an active connection to a Canary FlexNOTE: If you are using your 4G LTE Mount as a backup connection to your primary Wi-Fi connection, this LED will only be illuminated when the LTE backup connection is being used.4G LTE Mount does not have an active connection to a Canary FlexLED ColorsRear LED (Power)Amber SolidGreen SolidGreen BlinkRed BlinkOLED ColorsMiddle LED (Network)Amber SolidGreen SolidRed SolidFront LED (Device Connection)White SolidOSupport and moreMy Verizon mobile appManage your account, track your usage, edit account information, pay your bill and more.From your computer, visit verizonwireless.com/Support.Customer serviceCall 1.800.922.0204Twitter @VZWSupportAdditional informationYour wireless device and third-party servicesVerizon Wireless is the mobile carrier associated with this wireless device, but many services and features oered through this wireless device are provided by or in conjunction with third parties. Verizon Wireless is not responsible for your use of this wireless device or any non-Verizon Wireless applications, services and products including any personal information you choose to use, submit or share with others. Specific third-party terms and conditions, terms of use, and privacy policies shall apply. Please review carefully all applicable terms and conditions and policies prior to using this wireless device and any associated application, product or service.FPOFPOFPOFPOFPOFPOBall tightening screwFPO

Navigation menu