Quantenna Communications QSKU-610 802.11an AP User Manual QBOX610 Installation guide rev1 0

Download:
Mirror Download [FCC.gov]
Document ID	1494747
Application ID	OKy5HnvuLe8Y6xq3FzoBGw==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18kB (224960 bits)
Date Submitted	2011-07-05 00:00:00
Date Available	2011-07-05 00:00:00
Creation Date	2017-11-05 01:41:05
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-05 01:41:05
Document Title	Microsoft Word - QBOX610 Installation guide rev1 0
Document Creator	PScript5.dll Version 5.2.2
Document Author:	MandyLiang

Instaallation Guide
QBox6
610
WLAN LED
Resett to Defaullt button
LAN LED
WPS button
WPS LED
3‐w
way switch
Power LED
Ethern
net
Mode LED
Po
ower
Quickk start
How to Set up
1. SSet the 3‐way switch on the back o
of each QBo
ox610 device to Auto m
mode
2. Connect
thee Ethernet p
port from th
he router orr gateway to
o the Ethern
net port on one
QBox610
deevice using tthe Etherneet cable
3. Connect
thee Ethernet p
port from th
he STB or media player to the Etheernet port on the
other
QBox610 device using the otther Ethernet cable
Rev .
Page
4. Power on both QBox610 devices, wait for WLAN LED to blink and then turn solid blue
when the boxes are associated together
Mode Selection
The Mode switch at the back panel of QBox610 device can be set to one of the following three
modes:
Auto Mode: If 3‐way switch is set to Auto, the QBox610 will set its mode automatically. If the
device is connected to a router or gateway it will run in AP Mode otherwise it will run in STA
Mode. (QBx610 is set to Auto Mode from the factory).
AP Mode: If the 3‐way switch is set to AP, the device acts as an access point. The device in AP
Mode should be connected to a router or gateway.
STA Mode: If the 3‐way switch is set to STA Mode, the device acts as a client and it can be
connected to other wired devices such as STB and media player. The QBox610 in STA Mode
connects wirelessly to the QBox610 which is set to AP Mode.
Configure the QBox610 via Web GUI
By default, DHCP client is enabled in QBox610 and it will continue to request the DHCP server to
get the IP address.
To configure the QBox610 via Web GUI:
1. Connect the QBox610 to a PC via Ethernet port on the back of the device
2. Open any web browser and type the IP addresses according below:
http://192.168.1.100 for the box in AP mode if router or gateway is not connected
http://192.168.1.200 for the box in STA mode if router or gateway is not connected
3. If router or gateway is connected to QBOX610, please find out the IP addresses of the
QBOX610 devices from the attached tables of the router or gateway. Please look for the
device name: Quantenna
4. You can start configuring the devices via Web GUI. Default user name is user and
password is user.
Troubleshooting
On AP device:
Rev .
Page
Once the QBox610 is connected to Gateway, it fetches the IP address from the Gateway and
the Mode LED should be ON if the device is set to AP or Auto. If the Mode LED is OFF, check the
three‐way switch to make sure that it is on AP or Auto.
If the three‐switch is on AP or Auto but the Mode LED is OFF, please check if gateway DHCP
server is enabled.
On STA device:
To check the connection between Gateway and STA device, connect a PC to the STA device
through Ethernet connection and check the LAN LED and WLAN LED
LAN LED
LAN LED is on when the Ethernet cable is connected and blinking during the traffic. If the LAN
LED is OFF, make sure the Ethernet cable is connected to the device.
WLAN LED
Wireless LAN (WLAN) LED is ON when wireless connection is set up. During the association the
WLAN LED is blinking.
IF WLAN LED is OFF make sure the modes are sets correctly on the AP and STA device, wait for 5
minutes and the devices should connect. If the devices are still not connected, make sure they
are apart at least 3m or move the devices closer if they are very far apart.
WPS button
The security mode is enabled on every QBOX610 device before shipment. If user wants to reset
the security key, push the WPS button on both QBOX610 devices within 2 minutes to activate
the WPS feature. The WPS LED will start blinking and then turn solid once the new security key
is assigned.
Rev .
Page
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in
indoor environment only.
Rev .
Page
Generic QHS610 Product specification rev 1.2
Revision history
1.1 – Update the AGPIO_B_25 for mode LED, update the 3 way switch and DHCP mode definition.
1.2 – DHCP mode and static IP mode
LED section
LED
definition
POWER
LAN
GPIO assignments
Color
Behavioral model
N/A
N/A
GREEN
GREEN
WPS
AGPIO_B_3
GREEN
Wifi Link
AGPIO_B_2
BLUE
Wifi Quality
AGPIO_B_30
BLUE
Mode
AGPIO_B_25
GREEN
When +3.3V power is up, POWER LED turns on
When Ethernet Link (1000/100/10Mbps) is up,
the LAN LED turns solid.
When the WPS is triggered by push button or
WebUI, the WPS will blink every 3 second and
turns on solid after the WPS process is
completed.
When the association is done, Wifi Link LED
turns on. During association process, wifi Link
LED blinks in every 3 second.
When the throughput rate is higher than
30Mbps, Wifi Quality LED turns on
When AP mode is set, turns on mode LED, When
STA mode is set, turns off mode LED. Before
either mode is set, blink the LED every 3 second
3 Way switch
Function
STA
AP
Auto
DGPIO_B_8
DGPIO_B_0
Definition
Software will configure it to STA mode only
Software will configure it to AP mode only
Software will configure it based on the DHCP mode or
static IP mode
Push button
Function
WPS push button
RTD push button
GPIO
GPIO_B_4
GPIO_B_27
Definition
To trigger WPS feature
To restore the factory default settings
User guides on 3‐way switch and IP address assignment
QBOX610 has added a 3 way switch feature and DHCP client feature. This document describes how the
3 way switch works and how the IP address being assigned to the Video bridge. In order to support both
old mode (no 3 way switch) and new mode (3 way switch), a new parameter is introduced in
wireless_conf.txt file stored in /mnt/jffs2/ folder.
Parameter
“use3way=0” disable the 3 way switch feature
“use3way=1” enable the 3 way switch feature
Mode Configuration
Old mode – “use3way=0”
In old mode, user configures the mode of the device via the mode parameter in the wireless_conf.txt file
or via the WebGUI.
“mode=ap” is AP mode and “mode=sta” is STA mode
New mode – “use3way=1”
In new mode, user uses the 3 way switch button at the back panel of the QBOX to configure the mode.
TOP position – STA
MIDDLE position – AP
BOTTOM position ‐ AUTO
When the 3 way switch is in STA position, it is configured to STA mode only. When it is in AP position, it
is configured to AP mode only. When it is in AUTO position, then it depends if the DHCP mode or static
IP mode is enabled.
If DHCP mode is enabled via api command or WebGUI, the AUTO mode will set the QBOX to AP when
the device is directly connected to the Gateway router. Otherwise AUTO mode will set the QBOX to STA.
If static IP is enabled, the AUTO mode will set the QBOX to STA mode only.
IP address configuration
Old mode – “use3way=0”
In old mode, IP address is configured by user via the ipaddr file in /mnt/jffs2/. No DHCP mode is allowed.
New mode – “use3way=1”
In new mode, IP address is configured based on the DHCP mode or Static IP mode.
If DHCP mode is enabled, then the IP address is assigned by DHCP server.
If static IP mode is enabled, then user specify IP address via WebGUI.
DHCP mode or static IP mode
A new parameter is introduced in wireless_conf.txt file stored in /mnt/jffs2/ folder to select between
DHCP or static IP
staticip=0 means DHCP mode
staticip=1 means Static IP mode and the IP address is specified in ipaddr
User guides on 3‐way switch and IP address assignment
QBOX610 has added a 3 way switch feature and DHCP client feature. This document describes how the
3 way switch works and how the IP address being assigned to the Video bridge. In order to support both
old mode (no 3 way switch) and new mode (3 way switch), a new parameter is introduced in
wireless_conf.txt file stored in /mnt/jffs2/ folder.
Parameter
“use3way=0” disable the 3 way switch feature
“use3way=1” enable the 3 way switch feature
Mode Configuration
Old mode – “use3way=0”
In old mode, user configures the mode of the device via the mode parameter in the wireless_conf.txt file
or via the WebGUI.
“mode=ap” is AP mode and “mode=sta” is STA mode
New mode – “use3way=1”
In new mode, user uses the 3 way switch button at the back panel of the QBOX to configure the mode.
TOP position – STA
MIDDLE position – AP
BOTTOM position ‐ AUTO
When the 3 way switch is in STA position, it is configured to STA mode only. When it is in AP position, it
is configured to AP mode only. When it is in AUTO position, then it depends if the DHCP mode or static
IP mode is enabled.
If DHCP mode is enabled via api command or WebGUI, the AUTO mode will set the QBOX to AP when
the device is directly connected to the Gateway router. Otherwise AUTO mode will set the QBOX to STA.
If static IP is enabled, the AUTO mode will set the QBOX to STA mode only.
IP address configuration
Old mode – “use3way=0”
In old mode, IP address is configured by user via the ipaddr file in /mnt/jffs2/. No DHCP mode is allowed.
New mode – “use3way=1”
In new mode, IP address is configured based on the DHCP mode or Static IP mode.
If DHCP mode is enabled, then the IP address is assigned by DHCP server.
If static IP mode is enabled, then user specify IP address via WebGUI.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : MandyLiang
Create Date                     : 2011:06:23 13:49:52+08:00
Modify Date                     : 2011:06:23 14:05:41+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2011:06:23 14:05:41+08:00
Format                          : application/pdf
Title                           : Microsoft Word - QBOX610 Installation guide rev1 0
Creator                         : MandyLiang
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Document ID                     : uuid:449cf514-ea60-4a88-8bbf-05f207fa95b8
Instance ID                     : uuid:d6d73a26-9df9-43f0-832c-765999921ff2
Page Count                      : 9

EXIF Metadata provided by EXIF.tools