Quantun Electronics QP-250U Walkie Talkie User Manual

Quantun Electronics, LLC Walkie Talkie Users Manual

Users Manual

Thanks for selecting the QP-250 two way radio,This unit have a very attractive design:SMALL AND LIGHT, IT HAS APOWERFUL SPEAKER WITH A DIAMETER OF 40MM TOENSURE SHARP AND CLEAR SOUND WHEN YOU ARETALKING.The design follows the IP54 standard with a high level ofprotection against water damage and dust.The radio shouldkeep working properly even in adverse conditions.We are very confident that you will find the QP-250 radio areliable unit,able to efficiently satisfy your communication needs.Please read this User manual for detailed information on how tooperate the product correctly. ATTENTIONThis device complies with parts 15 of FCC rules.Operation is subject to the following two conditions:1)This device may not cause harmful interference,and2)This device must accept any interference received , including interference that may cause undesired operation.
List for radio and accessories01Table of contentsList for radio and accessoriesRadio and accessories *01Photo for radio and accessories *02Brief introduction of RadiosPanel structure description *03-04The contents for LCD *05Standard Features *06-08QUANTUN model list *09Assembly radio *10-11Charging informationBattery life NOTES *13Charging operation *14Radio’s operation *15-16Function setting *17Notice for the use of headphones *12After you read the information of the QP-250 radio,please openthe box, and then confirm that all radio parts are included ,andin good shape. Otherwise contact your reseller.Radio and accessoriesRadioBatteryBelt-clipAdaptorEarphoneHolding StrapUser manual1111111Parts Quantity
Brief introduction of Radios0302List for radio and accessoriesPanel structure DescriptionQP-250MPTT12345678910111213141516Photo for radio and accessoriesBatteryEarphone Belt-clipAdaptor Holding StrapRadioQP-250
Brief introduction of Radios0504Brief introduction of Radios1. PTT SWITCH: Push and hold to transmit, Release to receive2. MONITOR BUTTON: Push to turn on/off monitor3. MENU KEY: menu button for parameters setting4. UP KEY: Plus key for parameters setting5. DOWN KEY: Minus key for parameters setting6. POWER ON/OFF VOLUME CONTROL KNOB: Turns power ON and adjusts the audio level7. ANTENNA8. SPEAKER: Internal radio Speaker9. EARPHONE JACK: connect external speaker and microphone10. TX/RX LED: Red means Transmit, Green means Receiver or Squelch opened11. BATTERY12. CHARGER JACK: connect external power adaptor13. BELT-CLIP14. BATTERY MOUNT15. LCD16. MIC: Internal radio MICThe contents for LCDDTMF SCRVOXSCANIcon IconName NameKEYPAD LOCKVIBRATIONALERTAUDIO OPENEDCTCSSDCSBATTERY DISPLAYSCANVOXDTMFSCRSCAN FUNCTIONVOX FUNCTIONTX OR RXNot availableNot availableCHANNEL ANDCTCSS/DCS
Brief introduction of Radios0706Brief introduction of RadiosStandard Features1. RF power: 2w2. 32 Channels, Programmable 25 /12.5 KHz Channel Spacing3. 9 - Levels Squelch selectable Helps to increase or decrease receiver sensitivity.4. Voice Operated Transmit (VOX) Enjoy the convenience of hands-free operation when used with the corresponding optional accessory.5. CTCSS/CDCSS Set up workgroups/users with unique CDCSS/CTCSS codes to prevent groups or users of interference with each others.6. Monitor Allows you to monitor channels for activity7. Normal Scan & Memory Scan The radio will scan all channels when using normal scan and memory channels when using memory scan.8. Low Battery Alert Audible tone and visual display tell you when the battery is running down9. Time-out Timer (TOT) The feature allows for more efficient use of channels by limiting the amount of time of each transmission10. Battery Save The radio will enable battery save feature in standby mode. Pressing any key or receiving a signal will restore the radio to normal operation.11. Busy Channel Locked A channel already in use is not available to other users12. Wired Clone Easily copy the features of one radio to another13. Squelch Tail Elimination The function will minimize the annoying audio outputs that occur at the receiver on completion of a transmission.14. LCD backlight and with Backlight for Nighttime Operation15. PC Programmable You are able to customize the features of each radio for each user
Brief introduction of Radios0908Brief introduction of Radios16. Wall-adaptor charge Main board with charging control. Can be charged from wall adaptor directly17. Superior Audio A powerful speaker with a diameter of 40mm ensures clear, crisp and strong audio, even in noisy environments.18. Vibration This feature can be selected to use on noisy and other special environmentsQUANTUN model listModel Battery2WQP-250(V)Frequencyrange (MHZ)146-174MHZRF powerQP-250-1500AdaptorTC-022WQP-250(PMR)446-447MHZ QP-250-1500 TC-022WQP-250(U)450-470MHZ QP-250-1500 TC-02
Assembly radio1110Assembly radioBelt clip installationHold the radio in one hand,and push the belt-clip downin the allocated slot.Belt clip removalRaise the Snap with thefinger, and push the clipup to separate from radio.MPTTBattery installationPlace the battery parallel tothe back of the radio and slidein it,then press till it is locked inplace.Battery removalPush down with the finger thebattery latch,separate thebattery from the radio usingboth handsMPTT
Charging information1312Notice for the use of headphonesBattery life NOTESWhen you use a battery for the first time,or one that has beenin storage for a long period,make sure it is properly chargedbefore placing it in service.If you notice that,while transmitting ,the Battery Icon startsflashing,that is an indication that the battery is running out ofenergy and requires to be replaced or rechargedAttention: Please use the indicated batteries and chargers, the use of other units can damage the device or even generate an explosion Do not allow metal objects to contact the battery terminals, or dispose the battery in fire, Do not try to open the battery,It is not a repairable item The battery should be charged in an ambient temp between 5* to 40*,outside the range,the battery will not be fully charged. When in charging mode, do not use the radio. If the radio battery is not fully charged ,do not remove the adaptor plug. The battery ,after fully charged ,Should last about 8 hours of average use ,after that is should be recharged. if the radio or the battery is wet,please do not connect them to the charger,to avoid additional damage.When using the headphones, Begin with adjusting the volumeto your comfort level.Remove the rubber cover exposing the Accessory connector and insert the plug in straight line into the radio with the cableup parallel to the antenna as shown on picture to ensure properconnection.when removing the accessory,do not pull by thecable,since this could put an additional stress on the device,shortening it's life span.
Radio’s operation1514Charging information1. Open the radio The radio will self-inspect for 1 second first, including full-screen display, backlight lamps lit, and then issue a prompt start-up (three pitch).2. After the self-inspection, LCD will show the last state before Power off.3. Press PTT button, then transmitting, if the VOX is opened, Then you will just talk to the MIC and transmitting, when transmitting, the LED will change to red. And " " will be Transmitting state.4. When Receiving, The LED will change to green, and " " will be Receive state. When Vibration is opened and the signal is received, the radio’s speaker will be audible, and the radio will be 2 seconds vibration, one second stop, the cycle will be repeated until the monitor key is pressed; If the CTCSS or DCS for Receiver and the Transmitter are not the same, Receiver will not hear anything except for green light.5. When Battery voltage is less than 3.2 V, LCD will show "OFF", the radio will stop transmit and Should be promptly charged. When charging, the " " starts flashing, the radio can receive, but cannot transmit.Charging operation1. Plug the DC head of the adaptor into the DC jack of the radio.2. Plug the adaptor on the AC power outlet to keep normal charging.3. When the radio is power on, Battery icon on the LCD begins flashing, until the battery icon change to normal display (stop flashing), It means fully charged, unplug the DC head to use radio.3. When the radio is power off, the LED charges to red; when the LED charges to green, It means fully charged.
6. The keypad has two modes of operation a. CH MODE when the radio is turned ON, press MENU button shortly, the radio will be the CHANNEL MODE, press [ ] or [ ] button to select the desired channel. b. Function MODE when the radio is turned on, press MENU button with 2 seconds, the backlight will also be on, and the radio will be on Function MODE .You can now set up the required options with [ ] and [ ] button.Keypad locked functionPress “MENU+MONI”, LCD will show " " , you can use PTTand MONI button only, Press “MENU+MONI” again, the keypadwill be unlocked.Scan functionPress “MENU+DOWN”, LCD will show " " , the radio willbegin to scan, When stop in the channel Scan, Press "UP+DOWN"button and will scan in a row. Press “MENU+DOWN” again, thescan function will be off.SCANSelect Function OptionsConfirmEnter*BEEP*DCS*CTCSS*DCS/CTCSS Conversion**Busy*VOX*Vibration* DCS CTCSS* 1-9 level* and* 1-16 level* andPressMENUPressMENUToconfirmPressUPorDOWNSquechLever (1-105) (1-105)* and** (1-50)Function setting1716Radio’s operation
Safety and General Information SAFETYTRAINING INFORMATION Your QUANTUN radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your QUANTUN radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:  FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.  American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.  American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave.  The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:  DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio.  DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch.
 ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the QUANTUN belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your QUANTUN radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. OPERATING NOTES  When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 cm (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 cm (1 inch) from your head and body.  If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting. FCC CAUTION: Changes or modifications to this device, not expressly approved by QUANTUN , could void your authority to operate this transceiver under FCC regulations.

Navigation menu