Quanzhou Wouxun Electronics WOUXUN05 TWO-WAY RADIO User Manual 2
Quanzhou Wouxun Electronics Co., Ltd. TWO-WAY RADIO Users Manual 2
Contents
- 1. Users Manual 1
- 2. Users Manual 2
- 3. Users Manual 3
Users Manual 2
How to operate In standby, press + , the screen displays Press @to enter, it shows ‘ON’, press a / n to select turn ON/OFF the power saver luntion Press mite confirm, and then press to return to standby Selecting transmitting power (TXP) --- MENU 4 in frequency mode, press m + , the screen displays Press@ to enter, it shows ‘HlCiH', press n /0 to select HlGH/LOW power, then press@ to confirm, finally press to return to standby. )) This transceiver has HIGH and LOW transmitting power selectable >> The quick sWitch between the i-iioi-i and tow transmitting power is temporary ln transmitting mode, press key to quick swrteh the i-ilcl-l/tow transmitting power Once the transceiver is resumed, the transmitting power reverts to the original output power. 16 Gwouxun Processionai rm rranse ver Setting transmitting beginning/ending prompt (ROGER) --- MENU 5 This function is to select the prompt modes when beginning/ending transmitting as followings. OFF: Pressand release PTT key, there is no prarnpt for either beginning or ending tramsifilng BOT: Press Pi'r key, there is prompt for the beginning tramsltting EOT: Release PTl key, there is prompt for the ending tramsittlng. BOTH: Press and release PTT key, there is prompt for both be nning/ending tramslttlng. in standby, press fly + ,the screen display Press mm enter, it shows ‘orr', press a /n to select OFF/BOT/EOT/BOTH, then press m to confirm, finally press to return to standby Time-out Timer (TOT --- MENU 6 This function is to prevent the transceiver from transmitting for too long time When the transceiver is exceeding the preset time limit, it Will stop transmitting With an overtime alarm. This transceiver can be set in 40 levels with 15 seconds each between 15 and 600 seconds. in standby, press @ + ,the screen display Press in to enter, it shows ‘50', press u / n to select the desired transmitting level, then press- to confirm, finally press. to return to standby 17 How to operate Setting VOX (VOX) --- MENU 7 This transceiver Will SWitch to the transmitting mode when detecting the voice singal. The transmitting operation wil somewhat be delayed, and the Voice signal information may be not transmitted at the first beginning, since there needs some time for the VOX circuit to detect the voice signal. in standby, press m + 7 ,the screen displays Press m to enter, it shows ‘OFF', press a / n to turn OFF VOX function or select VOX level (1-10), then press an to confirm, finally press ‘to return to standby. )) The higher level of VOX is set, the higher volume is needed » in SCAN and RADIO modes, the vox functrbn is nbt available, but lust showing vox mark an the upper right or the aisplay scrcen Setting wide or narrow bandwit‘th (WN) in standby, press @ + m ,the screen displays Press @ to enter, it shows ‘WiDE', press u/ my to confirm, finally press. to return to standby 18 MENU 8 t WIDE/NARROW bandwidth, then press Setting voice guide (VOICE) --- MENU 9 in standby, press @ + m ,the screen displays Press an; to enter, press u/ a to select Chinese, English or OFF , and then press key to confirm, finally press to return to standby. >) Please turn off MENU 9 and MENU 11 at the same time to turn off all the vaice prompt for this transceiver Setting transmitting overtime alarm (T 0A) --- MENU 10 This alarm is the pre-alert time when the transmitting time is nearly up to requested transmitting time when the time is up, the transceiver sounds out the beep prompt and the LCD keeps flashing This transceiver can be set from 1 to 10 TOA level with 1 second each Level 1 means that the prompt 1 second ahead when the transmitting time is up to the TOT preset time In standby, press + n , the screen displays ‘ Press@ to enter, it shows ‘5‘, press u / n to select press finaiiy to return to standby / ~ 0 Level, then press m to confirm, 19 How to operate Beep prompt function (BEEP) --- MENU 11 Beep prompt function is for the transceiver operating confirmation, error status prompt or faulty condition reminders. We faithfully advise you to keep this function ON, so that you can detect or check the errors and faults in time. In standby, press + m , the screen displays _ Press -to enter, it shows ‘ON', press a / a to select turn ON/OFF the beep promptlngfunctlon, then press to confirm, press finally to return to standby NOTE » When MENU 9 VOlCE function and MENU ii BEEP function are both on at the same time, the VOlCE function is prioritized. Setting power on message (PONMSG) --- MENU 12 This transceiver has 3 display modes selectable for the power on message as follow- OFF: display the full screen BATT-V: display the current battery voltage MSG: display ‘WELCOME' In standby, press as" + m ,the screen displays Press-to enter, it shows ‘orr', press“ /fl to selectOFF/BATTsV/MSG, then press conftrm, finally press to return to standby 20 -t° Busy channel lockout (BCL --- MENU 13 This function IS to prevent the interference from the other communicating channels When the selected channel is occupied by others, press PTT and there Will be an alarm prompt for BCL, while release PW, the alarm prompt disappears and the transceiver Will be back to the receiving mode. In frequency mode, press + , the screen displays Press .to enter, it shows ‘OFF', press u /n to select ON/OFF this function, then press m to confirm, finally press to return to standby. Setting keypad lock (AUTOLK) --- MENU 14 This transceiver has automatical lock (AUOLK) and manual lock selectable ON: When the AUTOLK is on, there are no operations within 15 seconds, the transceiver Wlii be locked automatically Press more than 2 seconds to unlock the keypad OFF: The AUTOLK is off, it is only avaiable to lock the keypad manually. » According to the manual lock, press for more than two seconds to lock in standby mode, and press. for more than two seconds again to unlock it 21 How to operate in standby, press @ + ,the screen displays Pressflto enter, it shows ‘orr', press a /fl to selectON/OFF this function, then press m to confirm, finally press to return to standby. Setting receiving CTCSS (R-CTCSS) -- MENU 15 Using the CTCSS/DCS can be used for you to receive the speCified individual or group calls, and avaid the neediess caiiings from others with the same frequency Only receiving the sarne CTCSS/DCS signals, the transceiver can release the squelch. in frequency mode, press M + the screen displays to enter, it shows ‘OFF , press u /n to turn OFF this function or select 67.0Hz to 254.‘in crcss code, then press m to confirm, finaily press -to return to standby. >> This transceiver has so groups c‘rcss, see appendix (ii crcss frequency sheet 22 Setting transmitting CTCSS (FCTCSS) - in standby, press 1m + m Press -to enter, it shows ’OFF', press u /0 to turn OFF this function or select 67 OHz to 254 We CTCSS code, then press m to confirm, finally press to return to standby MENU 16 s ,the screen displays )) This transceiver has 50 groups CTCSS, see appendix (1) CTCSS frequency Sheet. Setting receiving DCS (R-DCS) --- MENU 17 in frequency mode, press + m ,the screen displays Press mm enter, it shows ‘orr', press a /n to turn OFF this function or seiect D023N to D754I DCS code, then press @ to confirm, finally press to return to standby. » rhis transceiver has 105 groups DCS, see appendix (2) DCS frequency sheet >> in DCS seiections, DXXXN (from DDBN to D754N) rneans POSITlVE code, while DXXXI (from D023! to D754!) means NEGATIVE code. 23 How to operate Setting transmitting DCS (FDCS) --- MENU 18 In standby mode, press m+ ,the screen displays Press@ to enter, it shows ‘OFF', press a lo to turn OFF this function or select D023N to D754I DCS code, then press my to confirm, finally press to return to standby >> This transceiver has 105 groups ocs, see appendix (2) ocs hequenq sheet )) In DCS selections, DXXXN (from DOZSN to D754N) means POSlTlVE code, while DXXXl (from DOZ3l to D754l) means NEGATlVE code Setting scan mode (SC-REW --- MENU 19 This transceiver has three scan modes TO: The transceiver continues scanning if there are no any operations 5 seconds after receiving signals. co: The transceiver pauses scanning when receiving signais, and cohnues scanning 3 seconds after the signal disappears. SE:The transceiver stops scanning when receiving signals, In standby mode, press + the screen displays Press@ to enter, it shows ‘TO', press u / n to select TO/CO/SE scan mode, then press to confirm, finally press to return to standby. 24 Gwouxun Professional FM Trans r Setting SCAN / LAMP l SOS-CH / FM Radio function on side key 1 (PF1) MENU 20 There are four functions selectable on the side key 1 of this transceiver- SCAN: Scan function LAMP: Lamp function SOS-CH: 505 function RADIO: FM radio function OFF: Disable this side key 1. SCAN function: in standby mode, press Side key 1 enter to activate scanning (scan mode can be set through MENU 19 Sean Mode Setting), while press any keys to stop scanning in de. in standby mode, press W + n ,the screen displays Press fito enter, press u /D to select SCAN, then press to confirm, finally press to return to standby 2. LAMP function: in standby mode, press Side key 1 to turn on the Lamp, and pre in standby mode, press m + n ,the screen displays Press. to enter, press a / n to select LAMP, then press u to return to standby y again to turn it off to confirm, finally press 25 How to operate 3. SOS-CH (SOS function): in emergency, the transceiver transmits the 505 Signals to the outside surrounding on the specified Channel or Frequency in Band A or Band 8. Meanwhile, the transceiver Will sound “wu-- wu n“ With the green light keeping flashing. it will transrnit signals every 5 minutes, lasting for in seconds each time. When the carrier signal receives in the SOS transmitting mode, the transceiver will automatically SWitch into the receiving mode. After the carrier Signals disappear, the transceiver switches back to the SOS transmitting mode. Please press any key to exit in the sos transmitting mode >> in msethe SOS-CH frequency you set rs not the master frequency, the tranceiver will automatically set the SOS-CH rrequencyio be the master frequency in the SOS-CH mode Meanwhile, the masterlvequencywill not restore the semngs before the $05 transrrirttlrig >> Please press m key to reset the master frequency In standby, press M + n , then screen displays j‘ tsp“, , then press mto enter, press a /n to choose SOS—CH submenu, the screen display press @ again to confirm, press u/ a to choose Band A or Band B, then press m to confirm, the transceiver sounds ”wu wu ” , meanwhile the RED/GREEN/FLASHLIGHT keeps flashing, which means SOS-CH function is ON After above settings, switch the transceiver to the standby mode, and prfis PF'I side key to transmit the SOS signal. 26 Gwouxun Protessianai rm rrarisc ver 4. RADIO function: ' Turning on the FM radi In standby mode, press Side key 1 to turn on. The screen displays then the indicator keeps rlashing, which means transceiver is automatically tuning the radio stations Once the transceiver gets tuned, it stops at thls radio station and starts the listenning ' Tuning the FM radio station: ln radio mode, press fl, , the radio keeps tuning the stations automatically and the green light keeps flashing at the same time until it succeed in searching the available stations. You can press a /- to manually tune the radio stations. 'Storing radio station: After detecting a radio station, press m , the screen displays , and then select one of the number keys between m and m the detected radio station Wl ue stored into the chip for your futrue use. The transceiver has two groups of storages selectable for your storing, and the default group is the first storage E.g. lf you want to store 55 1MH1 into the 1st group Channel 8, ln radio mode, when tuning the desired radio station, press m + m to store it into the lst storage directly if you want to store this frequency into the 2nd group channels. ln radio mode, when tuning the desired radio station, press then the screen will display Atthis time, pressm+ to store this station into the 2nd group Channel 3 in radio mode, press 1 to 9 key to select the stored stations accordingly to listen to, while use the- key to swttch between 1st and 2nd storages 27 How to operate ~ Exiting from the radio mode: Press Side key 1 again to exrt from the radio mode >> When the FM radio rs working, the curent frequency or channel is in standby. Once detecting the recelvmg Signals, the transceiver will autornatrcaiiy switch to receiving/transmitting mode Frve seconds after the Signal disappears, the transceiver Will switch back to the radio mode » in FM radio mode, press .to back to the current standby frequency, and press PTT to transrnit Five seconds after transmission, the transceiver will swrtch back to the radro rnode. 28 Gwouxun Processional FM rranse yer Working mode (CH-MDF) --- MENU 21 This transceiver has two options for the working mode- 1. Frequency mode (FREQ) 2. Channel mode There are three channel display selections in channel mode as follow. (DChanhel (CH) ®Frequency + Channel number (CH FREQ) ®Channel name (NAME) >> it is available to switch between the frequency mode and the channel mode manually or vra the programming software if you want, you can set the password for the rnode swrtch » The password for the rnode swrtch rs ONLY available to set vra KGrUvDiP programming software » There are e charaters consist of the password, while “000000“ rneans no password rs needed for the mode swrtoh Frequency mode (FREQ) and Channel mode switchable (D Without password input Iri standby, press fin + press m to confirm. 2 m , then press u n to choose working mode and finally 29 How to operate (2) With password input Please set the password for the mode switch via KGVUVD1P programming software This password is consist of 6 charaters from O to 9 The valid password should be made up by SIX digits except “000000“ In standby, press + «a , then press a /fl to choose one of FREQ/NAME/CH/CHFREQ. Pressm to confirm, then the screen will display the password input . Please input the preset password through the keypad, then the transceiver will switch to the selected mode >> At least one channel is stored ahead into the transceiver, so that the above settings for the mode svvitch is workable >> Quickly Switch between the frequency mode and the channel modetcm in standby, press +- key to swrtch the mode without password input, you can swrtch it directly Otherwise, you need to input the valid password accordingly Setting auto backlight (ABR) --- MENU 22 In standby, press ,the screen display Press -to enter, it shows ‘ON', press a / a to turn ON/OFF auto backlight function, then press to confirm, press return to standby. 30 Gwouxun Processional rm rraiisc yer » when the AER function is set ON, the backllght will not be activated in transmitting/receiving mode or pressing side key 2 otherWise, operating on the keypacl and the side key ‘I will activate the backlight automatically, Setting offset frequency (OFF-SET) --- MENU 23 Offset frequency means the difference between transmitting frequency and receiving frequency The range of the offset frequency for this transceiver is from 0 to 69 950MHZ In standby mode, press m + , the screen display Press@ to enter, then press 3 / n to select the listed orrset frequency, or manually input through key pad directly Press. to confirm, whlle press. return to standby In order to transmit and receive in different frequencies, lt ls necessaw to set the offset frequency and the frequency shift direction in the frequency mode. Please follow the below setting steps- 1 Set the working mode to the frequency mode 2. Set the frequency shift direction and offset frequency. 31 Owouxun mar FM Transceiver Deleting channel (DEL-CH) ------ MENU 28 in standby mode, press M + w , the screen displays Press@ to enter, and press a / n to select the desrred channel,then press@ to confirm, After the channel is deleted successfully press to return to standby Setting reset ---- MENU 29 This transceiver has two selections for the reset operation'VFO reset and ALL reset VFO reset means all the functlonai parameter set in frequency mode resumes to the factory setting ALL reset means all the functional parameter set in both frequency mode and channel mode resume to the factory setting 1. VFO Reset in standby mode, press @ + m ,the screen displays Press @to enter, and press a / a to select VFO, then press W ‘the screen display press again to confirm, and the screen display After this operatlon, the transceiver Will be resumed automatlcally 2. All Reset in order to avord the faulty operations, we suggest that you set the password for the ALL Reset vra 37
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Modify Date : 2011:06:16 15:31:11+08:00 Create Date : 2011:06:13 16:57:05+08:00 Metadata Date : 2011:06:16 15:31:11+08:00 Format : application/pdf Document ID : uuid:dce88681-f439-41ae-84b5-b2d540c15421 Instance ID : uuid:40c098fa-6fc4-4682-913f-7c0573b0faf1 Has XFA : No Page Count : 9EXIF Metadata provided by EXIF.tools