Quanzhou Wouxun Electronics WOUXUN08 TWO-WAY RADIO User Manual 2
Quanzhou Wouxun Electronics Co., Ltd. TWO-WAY RADIO Users Manual 2
Contents
- 1. Users Manual 1
- 2. Users Manual 2
Users Manual 2
Digital FM radio Turn on the Radio: Press side key PM (The default value of the radio key set is the radio mode ), the receiving light flickers green and it Will search the radio station automatically. When it accomplishes the search and starts up the radio listening, the green light stops. Operate the radio: Press SQL button, it means the transceiver is tuning the radio station (The radio can be tuned to the iistenning station automatically) and the receiving light flickers green during the station turning Turn off the radio: Press PF1 key to turn off the FM radio function in radio mode » The transceiver is stiii in Transmitting/Receiving standby when trie radio is on It goes back to the Transmitting/ Receiving mode when receiving the signals, and return back to the radio mode arter the signal disappears » Pressing PTT key to transmit or changing channis after 5 seconds, the transceiver Wiit automatically return to FM radio rriode 13 Transmit voice prompt This function is to choose the options or voice prompt tor transcmitting OFF: Turn off this function, so no prompt transmits BOT: Press FTT and prompt transmits. EOT: Release PTT and prompt transmits. BOTH: Both press and release PTT , prompt transmits Setting batterypack save mode (SAVE) The SAVE function is chosen, if there are no receiving signals or any other operations for 10 seconds on the transceiver, the transceiver Wlii activate the SAVE function automatically. in order to reduce the power consumption, this function can make the transceiver cut off the receiver Circuit for the moment, then re-open to detect signals for a while. if there are any receiving signals or operations, the transceiver will be activated immediately and exit from the SAVE mode 14 Battery capacity prompt There are 4 situations to estimate the battery capacity, when you re-start the transceiver, the green iight for receiving flashes four times, it means the capacity is very full. the green iight for receiving flashes three times, it means the capacity is full the green light for receiving flashes two times, it means the capacity is not full the green light for receivrng flashes one times, it means the capaCity is low. the red light for receivrng flashes four times, it means the capacity is empty and the battery need to be charged or recharged Selecting transmitting power Press PTT and topkey at the same time, to switch the transmitting power between High and Low power. >> If the transmitting iight flashes red once, it means the transceiver is working in LOW power >> If the transmitting iight flashes red twice, it means the transceiver is working in HiGH power » This function is temporariiy for the current power switching operation 15 Transmit over timer This function is to prevent any transmitter from being busy line or transmitting over time Meanwhile, it protects the transceiver from being damaged because of the overtime transmitting. if the transceiver continually transmits over the set time, the transmitting Will be interrupted With the voice prompt. This transceiver can be set in 40 levels With 15 seconds each, between 15 and 600 seconds Setting scan function This function is a mode for receiving all communicating channels without missing Press PM (in scan mode), the transceiver starts scanning one by one according to the scan order Once the transceiver detects signals, it Will sWItch to the detected channel for receiving This transceiver has the adding channel scan function, to enable to be defined into the desired channels. How to scan The transceiver stops scanning when detecting the signals on the frequency or memory channei It will continue or stop scanning according to the three options as below TO: After searching the signals, the transceiver continues scanning if there are no operations within 5 seconds Press PTT, it transmits the channel specified by encoder. After transmitting, the scanning stops too. 16 CO: The transceiver stops scanning when detecting signal, and continues scanning 3 seconds after the signal disappears. Press PTT, it transmits the channel specified by encoder. After the transmission, it stops scanning. SE: The transceiverstops scanning when detecting signal Press PTT, it transmits the scanned channel lf there are still no operations in it) seconds after the transmission, it willl be back to transmit the channel specified by encoder. Setting priority scan function if you want to monitor the other frequency and check the certain preferred frequency at the same time, you can set priority scan functon. E.G.: Scan six Common channels CH1, CH2, CH3, CH4, CH5, CH6 and set CH6 as the priority scanned channel Scanning sequence as iollowtng chart >CH1 >CH6 —>CH2 >CH6 >CH3 >CH6—>CH4 >CH6 >CH5 >CH6 If the transceiver detects signal on Priority Channel, it will call out its frequency Select the priority channel via programming software. 17 Adding scanning function » Only the added scanning channel can be listed to scan. » Editing method: Strictly via programming software Busy Channel lockout The function is to prevent the interference from other communicating channels. if the channel is in busy line and pressing P'l'l', the transceiver will not transmit signal but sound the alarm prompt VOX function (VOX) This transceiver will sWitch to the transmitting mode when detecting the voice Signal. The transmitting operation will somewhat be delayed, and the voice signai information may be not transmitted at the first beginning, since there needs some time for the VOX circuit to detect the voice signal. There are if) levels for the VOX of this transceiver The higher level VOX is set, the less sensitive the transmitting is. Setting voice guide (VOICE) This transceiver has Chinese and English selectable for the voice guide. 18 Receiving/Transmitting frequency programmable The receiVing/transmitting frequenmes can be programmable accordingly Within the original frequency range Low voltage prompt When the batterypack is on low voltage, the transceiver Will sound voice programmable to remind of being charged timely. Wire clone function a. installing batterypacks on source radro and target Transmitting red LED riashrng means radio and connect them via wireclone cable. transmittrng data when wire cloning b Arid then power target radio on Transmitting red LED distinguishes alter c Power on the source radio and hold on the MON! completing wireclone and the transceiver key at the same time returns to standby. d. Red LED on the source radio rlashes, while the green Transmitting red LED lasting riashrng Usmg wm done LED_en the target radio itashes, it shows the Wire means the Wireclone is iaiied and the clonrng is completely starts up transceryer returns to standby mode Receiving green LED flashing means recervrng data when wrre cloning Target radio Recewing green LED extrngurshes alter completing wireclone and the transceiver returns to standby. How to use the intelligent charger i, insert the AC plug into the electric fence outlet (AC 90-240W). the indicator flashes, it means the charger enters charging standby. 1, insert the battery into the charger, the RED LED lasts flashing, it means charging is on the progress. while GREEN LED lasts flashing, it means the charging completes >> when inserting the exhausted batten/pack into the charger. it will praccharge the batterypack in tneidrng Meanwhile the RED LED flashes. and the process will last ioezo minutes And then the charging is normal RED LED will last riashrng till the charging is ruii. And GREEN LED wril flash. » Trickling charging the exhausted batterypack can protect the lithium batterypack better. Programming guide (via USB programming cable) a Download, unzip and install the USB driver according to different operating system [7 Restart your computer, and it shows the driver is installed successfully. c Download and unzip the matching programming software. d Connect the transceiver with your computer Via the USB programming cable e Power on the transceiver and open the software. 20 t. Read from the radio to check the connection. g Setting on the software accordingly h Write to the radio )) If you get the message “failed connection“ when you try to read from the radio, please check the first five steps and the communication ports accordingly. )) Please note that once the first three steps are done well, the com port will be selected automatically when you open the software However, according to the different computer settings, the com port may be needed to reset, Please determine the port assignment from the demos manager of the computer and select the correct communication port, which is available ror the connection. »it the connection is still not OK, please try another cable or another transceiver on another computer to double check. 21 Trouble shooting Please check your transceiver carefully according to the below chart before making sure that the transceiver is faulty. If the problems continuously exsit, please reset your transciver to correct your wrong operation sometimes ( Problem Solution \ Cannot power on, 1. The battery may exhausted, please charge or recharge no power supply 2.The batten! is installed wrongly, please remove the battery and reinstall Batterypack can‘t 1.The batten! life is over, please change battew. work too long 2. Not charging completely, please make sure the batterypack is fully charged before removmg. Receiving light 1. Make sure the volume is maximum continually flashes, 2. Make sure if the CTCSS/DCS is the same With the other members, please but no sound from recheck and reset epeaker j 22 ( Problem Solution \ ln standby, the transcevler transmits Check if the VOX funchon 15 on and Its level setting is too low. automatically Without pressmg PTT key Some functions Check if the transcelver work ll’l channel mode Some funcllons only can be cannot be memorlzed memorlzed vla programming software m channel mode. Recelvlng slgnals from other groups whlle Please change the CTCSS/DCS frequencles for all group members communicatin \ g J 23 Technical parameter Prolessional Appendix 1 rcrcss ‘ 1 670 11 948 21 1318 31 1713 41 2035 2 693 12 974 22 1365 32 1738 42 2065 3 719 13 1000 23 1413 33 177 3 43 2107 4 744 14 1035 24 1462 34 1799 44 2181 5 770 15 1072 25 1514 35 1835 45 2257 6 797 16 1109 25 1567 36 1862 46 2291 7 825 17 1148 27 1598 37 1899 47 2336 8 854 18 1188 28 1522 38 1928 48 2418 9 885 19 1230 29 165 5 39 1966 49 2503 K 10 915 20 1273 30 1679 40 1995 50 2541 / 24 Appendix 2 ’Dcs ‘ 1 DOZSN 16 DO74N 31 D165N 46 D261N 61 D356N Z DDZSN 17 D114N 32 D172N 47 D263N 62 D364N 3 DOZGN 18 D115N 33 D174N 48 DZSSN 63 D365N 4 D031N 19 D116N 34 DZO5N 49 DZGGN 64 D371N 5 D032N 20 D122N 35 DZ12N 50 D271N 65 D411N 5 D036N 21 D1Z5N 36 D223N 51 D274N 66 D412N 7 D043N 22 D131N 37 DZZEN 52 D306N 67 D413N E D047N 23 D132N 38 D226N 53 D311N 68 D423N 9 D051N 24 D134N 39 D243N 54 D315N 69 D431N 1O DD53N 25 D143N 40 DZ44N 55 D3Z5N 70 D432N 11 D054N 25 D145N 41 DZ45N 56 DSTIN 71 D445N 12 D065N 27 D152N 42 DZ46N 57 D332N 72 D446N 13 D071N 28 D155N 43 D251N 58 D343N 73 D452N 14 D072N 29 D156N 44 D252N 59 D346N 74 D454N \ 15 D073N 30 D162N 45 D255N 60 D351N 75 D455N j 25 ’ Dcs \ 76 D462N HZ D516N 33 DEOGN 94 D645N 100 D723N 77 D464N B3 D523N 89 D612N 95 D654N 101 D731N 78 D465N 84 D526N 90 D624N 96 D662N 102 D732N 79 D466N 85 D532N 91 D627N 97 D664N 103 D734N 80 D503N 86 D546N 92 D631N 98 D703N 104 D743N \ 81 D506N 87 D565N 93 D632N 99 D712N 105 D754N j 26 ( Frequencres avauabre- ‘ 462 5500MH1, 462 5625MHZ 462 5750MHZ 462 5875MHZ‘ Frequency range 462 EDOOMHZ, 452 5125MH2, 462 6250MH2, 452 6375MH2, 462 6500MH2, 462 6625MH1, 452.5750MH2, 462.6875MHL 462 7ODDMH1, 462 7125MH1, 462.7250MH2, 467.5500MHL 467 5750MH1, 467 6000MH1, 467 6250MH1, 467 6500MH1, 467 6750MH1‘ 467 7000MHZ, 467 7250MHZ Memory channels 16 cnannels Voltage 7.4V DC Working temperature -3o‘c to so C Channels Conchanner or Disrchannel srmprex Power output 1w Mode F3E(FM) Maximum devialron < :SKHZ Adjacent enannel power < 76mm Slabllrty :5 ppm Sensmvrty < 0.2 yV Audro output power > 500mW Werght 228g Waterproof W55 \Size 61 x 1er 38 (mm) NOTE: Speerrrcauens are summed to be revised without pnor natrce 27 Optional Accessories Sixrway charger thmummw 0;; 'UQEr / Car charger 1700mAh Lrion batterypack Programming software "AA“ batterypack Erimmator EC: WIreclone cab‘e @§ (SL16) (ENC) Antenna adapter USB programmrng cable Speaker/Mr: Leather case 28 We endeavor to achieve the accuracy and completeness of this manual, but is still not perfect for any possible omission or printing errors. All the above specifications are subject to be revised without prior notice. English Version: 39833-P-1204-V2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-701 Modify Date : 2012:07:18 14:25:57+08:00 Create Date : 2012:07:18 14:25:50+08:00 Metadata Date : 2012:07:18 14:25:57+08:00 Format : application/pdf Document ID : uuid:cd0c9e47-5382-431c-b3d4-0523dba515d4 Instance ID : uuid:14ddec31-eef5-4c9f-af79-df80557f5bbb Page Count : 9EXIF Metadata provided by EXIF.tools