RAE Systems RMBLEB RMBLEB User Manual

RAE Systems, Inc RMBLEB

User manual

RAE Systems by Honeywell Revision3 Page 1 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. BLE module operation description Document Information Info Content Author(s) Revision 1.0 Document Status Draft Date 2018-8-14 Distribution Approvals Name Date Signature
RAE Systems by Honeywell Revision3 Page 2 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. Release Histroy Rev. Date Author Descripition 1.0 2018-8-14 FengJunjie Initial draft
RAE Systems by Honeywell Revision3 Page 3 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. Contents 1. Overview: ........................................................................................................................................ 4 1.1 Modem Overview: ............................................................................................................... 4 1.2 Key Features: ...................................................................................................................... 4 2. Modem Pin Definitions: ................................................................................................................... 4 2.1 Block Diagram:.................................................................................................................... 4 2.2 Power supplier(powered by host PCBAs): ......................................................................... 5 2.3 Current Consumption: .......................................................................................................... 5 2.4 RF specification: ................................................................................................................... 5 2.5 Antenna specification: ....................................................................................................... 6 3. Specifications .................................................................................................................................. 6 3.1 Physical Characteristics: ..................................................................................................... 6 4. Regulatory ...................................................................................................................................... 7
RAE Systems by Honeywell Revision3 Page 4 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. 1. Overview: 1.1 Modem Overview: The Honeywell BLE is a highly-integrated Bluetooth low-energy (BLE) module, which offers a complete solution containing all hardware features necessary for development of wireless application. The transmitted data are divided into packets and each packet is transmitted on one of the 40 channels with the channel spacing of 2 MHz. The first channel starts at 2402 MHz and continues up to 2480 MHz. It offers superior radio performance, based on TI CC2640R2F. 1.2 Key Features:  Ultra-compact size (46*26*1.6 mm)  BLE 5.0  UART interfaces  Low power consumption  Embedded antenna design  FCC and CE compliant  RoHS compliant, certified lead-free and halogen-free 2. Modem Pin Definitions: 2.1 Block Diagram:
RAE Systems by Honeywell Revision3 Page 5 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. 2.2 Power supplier(powered by host PCBAs): Symbol Min Typ Max Unit 3.3V 1.9 3.3 3.6 V 2.3 Current Consumption: Test condition Min Typ Max Unit Peak Sending data package 8 mA Average Low power mode 80 uA 2.4 RF specification: Test condition Min typ Max Unit Frequency Range 2402 2480 MHz Channel Space 2 MHz TX power RBW=1M VBW=3M 3 4 dBm Rx sensitivity PER 1% -85 dBm
RAE Systems by Honeywell Revision3 Page 6 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. 2.5 Antenna specification: 3. Specifications 3.1 Physical Characteristics: Parameter Unit Dimension 18.8*13.5*1 mm Operation temperature -40 to +55 ℃
RAE Systems by Honeywell Revision3 Page 7 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. 4. Regulatory Caution: 4.1. This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
RAE Systems by Honeywell Revision3 Page 8 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. 4.2. The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. When the FCC identification number or ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: SU3RMBLEB” or ”Contains IC: 20969-RMBLEB” and the information should be also contained in the devices’ user manual. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in
RAE Systems by Honeywell Revision3 Page 9 of 9 Copyright © 2018 Honeywell Analytics, All rights reserved. strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and user. 2) The transmitter module may not be co-located with any other transmitter or antenna.

Navigation menu