RC Model Fun NASA701 RADIO CONTROL User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1847543
Application ID	7A/lDiPI1RFWosMCmO+HLQ==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	349.46kB (4368206 bits)
Date Submitted	2012-11-28 00:00:00
Date Available	2012-11-28 00:00:00
Creation Date	2012-11-27 11:41:27
Producing Software	Corel PDF Engine Version 1.0.0.525
Document Lastmod	2012-11-27 11:41:39
Document Title	Users Manual
Document Creator	CorelDRAW 12.0 版

Three» Matter need attention about boot and pair
1.Before boot. please check ifthe gear switch is turn offor not(make sure be down) and lDEsttich is
turn offor not (make sure be up) . ifany swtich is turned off. it is nonsafety boot (display will flash [TH]
or [IDLE] . RF no signal output), wait until all be turn off.
2.Finish the code pairing with receiverwithin1 min. if overtime, it will tweet be..be.
Foun LCD function panel instruction
[MODEL] : Planes choice. Include: standard four channel(standard glider) delta wing CCPM+ CCPM-
Flybarless planes
[NAME] : configuration management, Export configuration or save current configuration
[GAIN] : Gyro sensitivity. set normal and stunt sensitivity
[D/R] : direction ratio. Adjust a movement direction ofthe plane's direction ratio
[EXP] : direction curve.Adjusta movement direction ofthe plane's exponential curve. shown as rocker
centra's sensitivity
[TH] : Throttle curve. Adjust normal and stuntthrottle curve
[PIT] : Pitch curve. Adjust normal and stunt pitch curve
[CH] : Channel reverse swithover. Change single servo's movementdirection
[SN] : Check series number.Check the equipment's series number (8 characters)
[DIS] : Check version, Checkthe equipmentfirm version
[DATA] : Check date of manufacture . Check the equipment's date of manufacture.
[8T1] [IDEL] [NOR] : <|DLE> switch status display(f|ap.stunt.norma|).
[STD] [MAS] [SLV] : <> teaching function. choose trainer plane‘ student plane.
KSTCK) : <> change rocker mode
[RFS] : <> recoverto factory setting.
[mmat ii i; E j
[swi [rims] ism]
[NF] [iiiuiiLE] [Mala]
V \/ V V V V \ ’
Di
”li/Jllo67 ”WEJE‘
Dl
D1
’ 5’5
Five\ The manualforallfunc on
Planesch e [MODEL]
1.This page is for chooing a plane type. plance choice includes: 1- standard tour channel(standard glider).
2-delta wing. 3-standard helicopter. 4- CCPM+. 5- CCPM-, 6- flybarless.
2.Press(MENU) into it. Press(+) or (-). choose the target (MODEL) and
then press (MENU).
3.choose new plane operate steps:
a.Press<+> up to choose planes
b.Press<+> down to choose planes
c.Press to save and exit
The interface choose model
Standard glider Delta wing
CCPM-
Standard helicopter
Flybarless
[NAME]
1.This page is for saving current configuration(al| settings are using) to transmitter internal file, or use a
configuration opening from internal file.
Internal file contains 12 files, first five are setted to corresponding mode. they are: file 1 CESSNA(match
AP302 receiver), file name:“C1"Picture 1; file 2 SKYFUN(match AP302 receiver),fi|e name:“J2"Picture 2,
file 3 F16(match AP302 receiver), file name: “F2"Picture 3; file 4 X3V, file name: “3V"Picture 4; file 5 X3,
file name: X3 Picture 5; file 6 to 12 are not setted. With all files, user can open to current use, cover save,
change name.
File 1 Picture 1 File 2 Picture 2 File 3 Picture 3
Fi|e4 Picture4
File 5 Picture 5 The interface of records
managment Picture 6
2.Pressto enter into menu, press<+> or <-> to choose [NAME] Picture 6
3.How to open specified file numberto current using configuration(open to current use) operate steps:
a.put up <|eft ear>, the number shown in display isthe internal file‘s file nmber Picture 7
b.Press <+> up to choose until to the specified file number. Picture 8
C,Press <-> down to choose until to the specified file number
d.Press  to choose the operation needed.
Press <+> or <-> move to until showing flash “OP" character(means open this file) Picture 9.Again
press ,finsh opeing operation and return to menu.
e.Press  to cancel and exit
xi
putup  Picture7 File 9 Picture 8 Open file Picture9
4.How to save current configuration to specified file number(cover&save) operate steps:
a.Put up , the number shown in display is the internal file's file nmber Picture 10
b.Press <+> up to choose until to the specified file number. Picture 11
c.Press <-> down to choose until to the specified file number
d.Press  to choose the operation neededt
Press <+> or <-> move to until showing flash “SA" character(means save to this file)Picture 1 2.
Again press ,finsh opeing operation and return to menu.
e.Press  to cancel and exit
put up <|eft ear> Picture 10 File 10 Picture11 Save file Picture12
5.How to appoint file number's file name( change name) operate steps:
a.Put up , the number shown in display is the internal file's file nmber,Picture13
b.Press <+> up to choose until to the specified file number.Now the displayed model icon is the
recorded preview model Picture14
c.Press <—> down to choose until to the specified file number. Now the displayed model icon is the
recorded preview model,
d.After choosing the file number needed, put downPicture 15, now the number shown in
display is the internal file's file nmber(just show 2 characters)
e.after showing file name, press<+> or <-> to change file name , Stir down  one time can
move fouces to next character.
F.Press  again, enter intor the operation:
Press <+> or <-> move to until showing flash “SA" characterlmeans save to this file)Picture 15.
Again press ,finsh opeing operation and return to menu.
g.Press  to cancel and exit
Put up  Picture 13 File 11 Picture 14 put down Picture 15
Save file Picture 16
(ml
AIN)
The sensitivity of
1 Gyro sensrtivity. set normal and stunt sensrtivrty. The function just valid to the model have gyro system: Note: Tl
2 Press desktop(MENU), enterthe menu. Press(+)or(-), choose(GA|N)and thenPress(MENU) Picturet7
3 Normal sensitivity adjust: Operate Step:
a. Turn(|DEL)switch to up position, display (NOR)MARK (Means normal sensitivity) Picture18
a. Press(+), adjust the normal sensitivity up
b Press( - ), adjust the normal sensitivity down
c. Press(EXIT) to quit
4 stunt sensitivity adjustment. Operate step
a Turn the(|DEL) switch down. display(|DEL)MARK, (Mean Stunt sensitivity) Picture19
a. Press(+), adjust the stunt sensitivity up
in. Press( - ), adjust the stunt sensitivity down
c. Press(EXlT) to quit
Gyro sensitivity interfaCe Turn(lDEL)switch to up position Turn the(|DEl_) swrtch down
Picture17 Picturets Prcture19
Movement ratio [D/R)
1. This page used to adjust model direction ofthe servo movment ratio
2 Press (MENU)from desktop, enterthe MENU, press(+) or (-), choose (DIR), PRESS (MENU) enterthis
pagePrctureZU
3. Operate Step:
.Press( MENU), choose the number ofthe direction should be adjust(1ear|eron;27elevator;4r Rudder)
. Press (+), up to adjust the ratio
. Press(-), down to adjust the ratio
Press(EX|T), save and exit.
at
not:
4.
movementratio PictureZO aileron ratio Prcture21 elevatorratio Picture22
rudder ratio Picture23
Idex curve XP)
1. This page used to adjustthe idex curve of the model control direction.Show that the sensitivity of the
middle stick
2. Press (MENU) into it, press(+) or (-) . choose (EXP),afterthat enterthis page.Picture 24
3. Operate Step:
3. Press(MENU), choose the number of the direction should be adjust ( 1-aileron; 2-elevator; 4- Rudder)
b. Press (4-), up to adjust the ratio
c. Press(-), down to adjust the ratio
d. Press(EXlT), save and exit
11m
Index curve Picture24 Aileron ration Picture25 Elevator ratio Pictureze
Rudder ratio Picture27
Throttle curve (TH)
1. This page used to adjust the normal throttle curve and stunt throttle curve. Note: Stunt throttle curve just
applyto the helicopter
2. Press(MENU) into it, press(+) or(-), choose (TH), press (MENU) into this page. Picture28
3. Normal throttle adjustment Operate step:
3. Turn the switch (IDEL) up. display (NOR). Mark ( mean normal TH curvelPictureZQ
b. Press(MENU), choose the point location should be adjust ( contain 5 point cure)
c. Press(+), turn the numerical point location up
d. Press(-), turn the numerical point location down
e. Press(EXIT),quitand save
4. Stunt throttle adjustment Operate step:
.Turn the switch (IDEL) down, display (IDEL), Mark ( mean StuntTH curvejPictureSO
. Press(MENU), choose the point location should be adjust (contain 5 point cure)
.Press(+), turn the numerical point location up
.Press(-), turn the numerical point location down
.Press(EXlT), quit and save
«anon-n:
Throttle curve Pictureza Turn the switch (IDEL) up Turn the switch (IDEL) down
Picture29 Picture30
/‘\
5.Normal throttle curve
throttle CUFVEyfirS‘ PDim throttle curve.second point throttle curve,third point
Picture31 Picture32 Picture33
throttle curve.forth point throttle curve,fifth point
Picture34 Picture35
Stunt throttle curve:
throttle curve.first point
Picture36
throttle curve.second point throttle curve,third point
Picture37 Picture38
throttle curve,forlh point throttle curve,fifth point
Picture39 Picture40
Pitch curve [P | T)
1. This page used to adjust the normal pitch curve and stunt pitch curve. Note:The pitch curve only works
with helicopters
2. Press ( MENU) into it. press(+) or(-), choose(PlT). and then press (MENU) to this page.Picture41
3. Normal pitch curve adjust Operate step:
a. Turn the switch(|DEL) up, display (NOR), MARK( means normal pitch curve).Picture42
be Press(MENU), choose the point location should be adjust ( contain 5 point cure)
c. Press(+), turn the numerical point location up
dv Press(-), turn the numerical point location down
2. Press(EXIT), quit and save
4, Stunt pitch curve adjust Operate step:
as Turn the switch(|DEL) down, display (NOR), MARK( means stunt pitch curve).Picture43
b. Press(MENU), choose the point location should be adjust ( contain 5 point cure)
ct Press(+). turn the numerical point location up
d. Press(-), turn the numerical point location down
e. Press(EX|T), quit and save
a E
Pitch curve Picture41 Turn the switch(|DEL) up Turn the switch(lDEL) down
Picture42 Picture43
/,
\172
5. Normal pitch
3‘-
Pitch curve,first point Pitch curve,second point
Picture44 Picture45
pitch curve,third point
Picture46
Pitch curve.forth point throttle curve,fifth point
Picture47 Picture48
Stunt pitch
Pitch curve.first point Pitch curve,second point pitch curve,third point
Picture49 PictureSO Picture51
Pitch curve,forth point throttle curve.fifth point
Picture52 Pictur953
Channel reverse swu ver [REV]
I. This page used to change single servo's movement direction.
2. Press(MENU)inlo it. press(+)or(-). choose(REV),and then press(MENU)into this page.Picture54
Picture54 Channel reverse switchover
a. Operate Step:
a. Press(MENU), choose the channel number should be adjusted.
B. Press(+)or (-), choose the channel reversely.
o. Press EXIT, quitand save.
heck series number [SN]
1. This page used to check only series number
2. Press(MENU)into it, press(+)or(-), choose(SN),and then press(MENU)into this page.Picture55
PF
3, Operate Step:
a. Press(+), display two bit byte on the right
b. Press(— ). display two bit byte on the left
0. Put down lhe (left ear), in this way the characler can _
d. Press EXITto quit ~ Plcture55
Series number
Firmware [0/3]
1 This page used to check the firmware
2. Press(MENU) into it, press(+)or(-), choose (D/S), Press (MENU)to this page.Picture56
3 Operate Step:
a. Press(+), display two bit byte on the right
b. Press(- ), display two bit byte on the left
c. Put down the (left ear), in this way the
character can auto rolling.
d. Press EXIT to qui
Produce date [DAT]
1. This page used to check the produce date
Picture56
firmware interface
2 Press(MENU) into it, press(+)or(-), choose (DAT), Press (MENU)to this page BOJPG(produce date
interface)Picture 57
3. Operate Step:
a Press(+), display two bit byte on the right
b Press(- ), display two bit byte on the left i Picture57
c Putdown the (left ear), in this way the » produce date interface
character can auto rolling.
D Press EXIT to quit
[STICK MODE]
1 This page used to change the stick mode (MODE1,MODEL2,MODE3,MODE4),You need change the
transmitter mechanical if you would like to change the stick mode, be sure that clear know what you
are doing .
2 Press(MENU)then boot.Picture58 press(MENU)from desktop to enter, press(+)or(-),choose (STICK
MODE), Press(MENU)into this pagePictureSB
3 Operate step:
a. Press(+) key, to turn upward stick mode
b. Press(-) key, to turn down stick mode
6. Press EXIT Key, save and quit.
sin. A
BOOT Picture58 Stickmodeinterface MDDEI PictureGO
Picture59
MDDEZ Picturefi‘l
TD)
i.This page used to setteaching function.(Advanced)
Teaching function Including 3 teaching mode:(STD)show standard mode,to suit regular use. In the condition
trainer, trainee, should start studenttransmitter and pair with the receiver. afterthat starttrainertransmltter.
The transmitter ofthe trainer use (left ear) upward, the studenttransmitter control the receiver). Use teaching
function, caused pair, control different with the standard mode, pleasure be make sure thatyou clear know
what you are doing before set teaching function.
2. Press(MENU)boot, enter thelMENUlfrom desktop key, press(+)or (-).choose (STD).Press(MENU)
enter this page Picture62
3, Operate Step:
a. Press(menu)key,move the focal point to adjustwhich item should be adjusted.Picture62
Show twinkle (STD), mean choose the slardard mode
Show twinkle(MAS), mean choose train mode
Show twinkle(SLV),mean choose student mode
b. When show (MAS) during twinkle. you can input the series number of the student plane. be used
match with the student plane.
Number column show 1, press (+) or ( - ), input the first series number. Picture63
Number column show 2, press (+) or ( - ), input the second series number. Picture64
Number column show 3, press (+) or ( - ), input the third series number. Picture65
Number column show 4, press (s) or ( - ), input the forth series number. Picture66
Number column show 5, the figure show “AT means would auto match with student plane when boot.
Picture67
o. Press EXIT, save and quit
“*1
Teaching fuction Picture62 Revised the first series Revised the second series
Three kinds modes number Picture63 number Picture64
Revisedthethird series Revised theforth series Auto match Picture67
number Picture65 number Picture66
ctory settings [RFS]
1. This page used to recovery the transmitterfactory settings. After recovery to factory settings, the
adjusted materials will be disappeared, please be careful!
2. Press(+)and (-)atthe same time, then boot Picture68. press(MENU)from the interface, enterthe
menu, choose(RFS), Press(MENU)into this page Picture69
3, Operate step:
a. Press(MENU), to excute factory settings, afterfinish it auto start.
b. Press EXIT, quit.
P”
BOOT Picture68
Factory settings interface
Picture69
SKWMEB‘T’é'é'
R/C MODEL FUN CO.,LTD
Address: 420 mm Mh Noon Nanyou commercia‘ Serwces Bui‘dmg,
No.21 DengLiang Rd‘ Nan shah District Shenzhen‘ Chma
TEL:00857755786224311 00867755786224211
Fax: 00867755761558455
EmaH:maHa@skyarlec.com
WWW.SKYARTEC.COM

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2012:11:27 11:41:27+08:00
Creator                         : CorelDRAW 12.0 版
Modify Date                     : 2012:11:27 11:41:39+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2012:11:27 11:41:39+08:00
Creator Tool                    : CorelDRAW 12.0 版
Format                          : application/pdf
Title                           : 20120928英文版.cdr
Document ID                     : uuid:ef3a41c1-5c08-4a70-99c2-f0427d66e1f9
Instance ID                     : uuid:e2ca3d0b-cf94-423c-94b9-cb3206b79844
Producer                        : Corel PDF Engine Version 1.0.0.525
Page Count                      : 10

EXIF Metadata provided by EXIF.tools