RELACART ELECTRONICS PM160 Wireless In-Ear Monitor Systems User Manual PM 160

Download:
Mirror Download [FCC.gov]
Document ID	1625488
Application ID	wsAIA7a8kp993g7SCscLzg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	52.16kB (651968 bits)
Date Submitted	2012-01-20 00:00:00
Date Available	2012-01-20 00:00:00
Creation Date	2011-06-01 02:31:02
Producing Software	Corel PDF Engine Version 3.0.0.667
Document Lastmod	2011-06-01 02:31:02
Document Title	PM-160英文说明书
Document Creator	CorelDRAW
Document Author:	微软用户

PM-160
Professional Wireless
In-Ear Monitor Systems
Installation and Operation
Contents:
Introduction……………………………………………………………………………………..
Transmitter Installation and Connections………………………
Installation………………………………………………………………………
Connections………………………………………………………………………
Transmitter Controls and Functions………………………………………………….
PM-160 Front Panel…………………………………………………………………………
PM-160 Rear Panel……………………………………………………………….
Receiver Controls and Functions…………………………………..
PM-160R Front Panel………………………………………………………………………….
PM-160R Upper Side………………………………………………………………………….
Receiver Battery Installation…………………………………………………………………
System setup………………………………………………………………………………………
PM-160 Transmitter Setup…………………………………………………………………..
PM-160R Receiver Setup…………………………………………………………………..
Specification…………………………………………………………………………………….
Thank you for choosing a RELACART professional wireless in-ear monitor system. You have joined
thousands of other satisfied customers. Our years of professional experience of design and
manufacturing to ensure our products' quality, performance and reliability.
FCC warning statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 74
of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
.. Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
. Connect
the equipment into an outlet on a circuit different from that to which the receiver is connected.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to
operate this equipment.
This device complies with part 74 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
P1
P2
01
02
Introduction
①EIA-standard metal materials half - rack transmitter chassis.
②All the receivers offer durable, ergonomic metal bodies, soft-touch controls.
③UHF frequencies and Antenna Diversity reception for interference-resistant operation.
④Bandwidth 16MHz, 32 pre-programmed frequencies available.
⑤Selectable stereo or mono audio output.
⑥High-visibility white LCD information display
⑦ PLL (Phase Lock Loop frequency control) design ensures transmission reliability, "Noise
Lock" squelch effectively blocks stray RF.
⑧ Designed for use on performance, broadcast, big meeting as side-ear systems for
synchronous translation.
Transmitter Installation and Connections
Installation :
① For better operation the transmitter should be at least 3ft. (1m) above the ground and at least 3ft. away
from a wall or metal surface to minimize reflections.
② Keep antennas away from noise sources such as computer, digital equipment, motors, automobiles and
neon lights, as well as away from large metal objects.
③Attached a UHF antenna to the antenna input jacks, the antenna are normally positioned in the shape of a
“V” (in 45°from vertical) for best transmission.
④Keep open space between the receiver and transmitter for better reception.
⑤The transmitter should be at least 6ft. (2m) from the receiver.
Connections:
① The switching power supply is designed to operate properly from any DC power source 12V, 500mA
without user adjustment. Simply connect the transmitter to a standard DC power outlet, using only an IECtype input cordset approved for the country use. Power to the unit is controlled by the front panel power
switch.
②There are two audio inputs on the rear panel: 1/L and 2/R audio INPUTS. It is suitable for an XLR balanced
audio input connector and a 1/4” (6.3mm) unbalanced phone jack input connector. The two audio inputs
permit simultaneous feeds from two different outputs. Use the appropriate shielded audio cable for
connections between the transmitter and the output(s) of the mixer or other audio output equipment.
PM-160
Wir ele ss In -ea r
Mon ito r Sys tem s
mo ni to r
P3
P4
03 Transmitter Controls and Functions
Figure A: PM-160 Transmitter Front Panel
Figure B: PM-160 Transmitter Rear Panel
4 5 6
①Power Switch：Press power switch in 3 seconds and the transmitter readouts will light.
②Monitor: Earphone output jack.
③ LCD Window: Liquid Crystal Display indicates control setting and operational readings. See
“System setup” on page X for details.
④ UP / DOWN Buttons: Press Up or Down arrow button, in conjunction with the Set button, to step
through menus, select operating frequency and edit transmitter function choices.
⑤ SET Button: Use in conjunction with the Up / Down arrow buttons to step through menus, choose
operating frequency and select transmitter function options.
P5
①Antenna Input Jack: BNC type antenna connector, attached the antenna directly.
②RF POWER Output: Two-position switch adjusts RF power output, with LOW of 30mW, HIGH of
100mW.
③1/L Unbalance LOOP OUT output jack: Unbalanced 1/4” (6.3mm) phone jack to be connected to
another PM-160 transmitter's Balanced Input.
④2/R Unbalance LOOP OUT output jack: Unbalanced 1/4” (6.3mm) phone jack to be connected to
another PM-160 transmitter's Balanced Input.
⑤1/L Balanced Input Jack: XLR type connector. A standard 2 conductor shielded cable can be used to
connect the transmitter input to a balanced output on a mixer or integrated amplifier.
⑥2/R Balanced Input Jack: XLR type connector. A standard 2 conductor shielded cable can be used to
connect the transmitter input to a balanced output on a mixer or integrated amplifier.
⑦DC Power Output Jack: 12V / 500mA.
P6
04
Receiver Controls and Functions
10
11
①Power indicator
②Left and Right Channels Balanced Switch: To balance the volume of left and right channels
for the earphone.
③Earphone Jack.
④Mono or Stereo Selector Switch: If selecting Stereo, indicator (⑧) lights.
⑤Power Switch.
A: Power supply switch: Turn on this switch, the power indicator is in green.
B: Volume control: Once the receiver power is ON, adjust this switch to control the volume of
earphone.
13
12
P7
⑥LCD Window: Liquid crystal display
indicates operational frequency, channel and
battery condition. The transmitter's “fuel
gauge” battery indicator displays a maximum
of 4 bar segments. When it leaves 1 bar
segment, the batteries should be replaced
immediately to ensure continued operation.
⑦Antenna Diversity Receiving Signal
Strength Indicator
⑧AF Signal Indicator.
⑨Stereo Indicator.
⑩SET Button: Use in conjunction with the Up /
Down arrow buttons to step through menus,
choose operating frequency and select
receiver function options.
⑪UP / DOWN Buttons: Press Up or Down
arrow button, in conjunction with the Set
button, to step through menus, select
operating frequency and edit receiver function
choices.
⑫Battery Door Switch: Open the battery door
by liding the switch.
⒀Battery Compartment: Insert 2fresh 1.5V AA
batteries. (Alkaline type is recommended,
always replace both batteries.) Observe
correct polarity as marked inside the battery
ompartment
P8
05
System Setup
PM-160 Transmitter Setup
Receiver Battery Installation
P9
①Turn down the AF level of the associated mixer or amplifie.
②Turn on the transmitter, the LCD displays the preset data.
③ Change the frequency by manual: Press ﹤ /﹥ button to change the frequency, then “ SET” to confirm the
selected frequency.
④To enter the menu mode: Press and hold the SET button 3 seconds to enter the edit mode, touch ﹤/﹥ button
once to select and set RENAME, SENSITI, LOCK, DISP, INPUT or LEVEL.
A, RENAME: Selecting “RENAME”, then touch “SET” Button to enter edit mode(System consented name is
PM-160), when the first number flashes, touch ﹤ /﹥ arrow button to choose any number(0-9) or letter(A-Z) or
character. After the first number has been picked up, press ”SET” button, then the second letter flashes, and
repeat the first step operation till the sixth letter is programmed. Touch “ SET” button to confirm the desired
choice.
B, SENSITI (sensitivity): Selecting “SENSITI”, then touch SET button to enter edit mode, touch ﹤/﹥button to
select “HIGH” or “LOW”. Touch “SET” button to confirm the desired choice.
C, LOCK: Selecting “ LOCK” , then touch SET Button to enter edit mode, touch ﹤ /﹥ arrow button to select
“ON” or “OFF”, if stopping on “ON”, the system enters lock mode, the user can not use any button for any
control; if stopping on “ OFF” , the user can do any control by any button. Press SET Button to confirm the
desired choice.
D, DISP (display): Selecting “ DISP” , then touch SET Button to enter edit mode, touch ﹤ /﹥ arrow button to
select “ FREQUENCY” (frequency), “ CHAN” (channel) or “ NAME” . If stopping on “ FREQ” , the LCD will
display the operational frequency; if stopping on “ CHAN” , the LCD will display the operational channel; if
stopping on “NAME”, the LCD will display the user name; finally press SET Button to confirm the desired choice.
E, INPUT: Selecting “ INPUT” , then touch SET Button to enter edit mode, touch ﹤ /﹥ arrow button to select
“MONO” or “STEREO”. If stopping on “MONO”, it is transmitting mono; if stopping on “STEREO”, it is
transmitting stereo. Touch SET Button to confirm the desired choice.
F, LEVEL (for the volume of earphone): Selecting “LEVEL”, then touch SET button to enter edit mode, touch ﹤
/﹥button to scroll through the available choice for the function. The squelch level is adjustable in 80 1dB steps,
providing 0dB to -80dB range. Press SET Button to confirm the desired choice
P10
PM-160R Receiver Setup
BAND MIX
SOLO MIXES
AUX 3 OUT
PM-160T
AUX 2 OUT
PM-160R
AUX 1 OUT
①Turn on the receiver, the LCD displays the preset data.
②Change the frequency by manual: Press ﹤/﹥ button to change the frequency, then “SET” to confirm the
selected frequency.
③To enter the menu mode: Press and hold the SET button 3 seconds to enter the edit mode, touch ﹤/﹥ button
once to select and set SQ, LOC or P OFF.
A, SQ (squelch): Selecting “SQ”, then touch SET Button to enter edit mode, the small data flashes to indicate
edit, touch ﹤/﹥button to scroll through the available choice for the function. The squelch level is adjustable in
ten 5dB steps, providing a 50dB range. Press SET Button to confirm the desired choice.
(SQUELCH of receiver has been preset before finishing production. If interference is a problem, first consider
trying a different frequency. If it is not very necessary, please do not adjust the SQUELCH randomly. This will
be bad for the system. )
B, LOC (lock): Selecting “LOC”, then touch SET Button to enter edit mode, touch ﹤/﹥arrow button to select
“ON” or “OFF”, if stopping on “ON”, the system enters lock mode, the user can not use any button for any
control; if stopping on “OFF”, the user can do any control by any button. Press SET Button to confirm the
desired choice.
C, P OFF (power off): Selecting “P OFF”, then touch SET Button to enter edit mode, touch ﹤/﹥arrow button
to select “OPEN” or “CLOSE”, if stopping on “OPEN”, the unit will turn off automatically in 30 minutes if it
is outside the communications service area ( no signal available ); if stopping on “CLOSE”, the unit has to be
turned off by manual. Press SET Button to confirm the desired choice.
PM-160R
PM-160T
调音台
PM-160R
PM-160T
P9
P10
05
P9
Specifications
PM-160R Stereo Mini Receiver
PM-160 Stereo Transmitter
Channels: Single Channel
Frequency Stability: ±0.0005%, Phase Lock Loop frequency control
Carrier Frequency Range: UHF 618-936 MHz
Modulation Mode: FM stereo modulation
Operating Range: 80M typical ( in open space)
Oscillation: PLL synthesized
Sensitivity: 6dBμV, S/N>60dB at 25 deviation (mono)
Band Width: 16MHz
Max. Deviation Range: ±68KHz
S/N: ＞105dB
T.H.D.: ＜0.7% @ 1KHz
Frequency response: 45Hz～18KHz±1dB
Stereo Separation: ≥45dB (at 1KHz)
Output Connector: 3.5mm (φ) stereo earphone connector
Output Power: 2 X 150mW at 1KHz (THD3%)
Battery: AA X 2
Current Consumption: 185mA typical
Battery Current / Life: Approximately 7 hours
Dimension (mm): 108(H) X 66(W) X 22(D)
Weight: 190g
Main Frame Size: EIA STANDARD 1/2 U
Channels: Single Channel
Frequency Stability: ±0.0005%, Phase Lock Loop frequency control
Carrier Frequency Range: UHF 618-936 MHz
Modulation Mode: FM stereo modulation
Output Power: 30mW – 100mW
Operating Range: 100M typical ( in open space)
Oscillation: PLL synthesized
Spurious Rejection: ＜-60dBm
Maximum Deviation Range: ±68KHz
Band Width: 16MHz
S/N: ＞105dB
T.H.D.: ＜0.7% @ 1KHz
Frequency response: 45Hz～18KHz±1dB
Audio Input: Line level X 2,XLR and 6.3mmφ compound jack
Audio Output: 6.3mmφ unbalanced jack X 2
Dimension (mm): 210(W) X 43(H) X 206(D)
Weight: 1.2kg
P10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 8
Create Date                     : D:20110601023102
Modify Date                     : D:20110601023102
Producer                        : Corel PDF Engine Version 3.0.0.667
Author                          : 微软用户
Creator                         : CorelDRAW
Title                           : PM-160英文说明书

EXIF Metadata provided by EXIF.tools