RF Technology RF-215D RF Amplifier User Manual RF215D MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	66809
Application ID	nxGLJGvZWvHEYbexvrLkpw==
Document Description	RF215D MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.69kB (8605 bits)
Date Submitted	1999-10-27 00:00:00
Date Available	2000-03-15 00:00:00
Creation Date	2001-05-21 12:20:35
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-05-21 12:20:37
Document Title	RF215D MANUAL

RF TECHNOLOGY, INC.
16 TESTA PLACE
SOUTH NORWALK, CT 06854
PHONE 203-866-4283
FAX 203-853-3513
E-MAIL RFT@RFTECHNOLOGY.COM
WEB WWW.RFTECHNOLOGY.COM
RF-215D
AMPLIFIER
MANUAL
RF TECHNOLOGY, INC.
RF-2185D AMPLIFIER
DESCRIPTION
The RF-215D amplifier consists of a regulator board and RF amplifier boards mounted in a machined
aluminum weatherproof housing. The RF-215D amplifier is not field repairable due to the expertise and
test equipment required to effectively make repairs. A general description of the RF amplifier section and
the operation of the regulator circuit are presented for information purposes.
REGULATOR:
The regulator regulates the input voltage (+10.6 to +18VDC) to +10.0V and generates a –5V voltage.
A +5V regulator (U2) provides the reference voltage for the regulator consisting of U3A and Q1. The
regulated voltage of +10V is set by R6.
The +5v output of U2 is also fed to a dc-dc converter IC (U1) through a filter consisting of L1, C19 and
C20. The –5V output of U1 is used to control the current in the microwave FET transistors. A circuit
(U3B) is used to turn off the regulator transistor Q1 until the –5V is present or in the event of the loss of
this negative voltage. This circuit is required because a microwave FET transistor can be damaged if the
+10V were to be applied before the current regulating –5V is available.
The regulator circuit board also contains a detector amplifier consisting of U4A and U4B that amplifies
the RF detector output to level used for indicating the presents of an RF output signal.
A mute input provision is provided on the regulator board for muting the RF output when a transmitter is
placed in the standby mode.
RF AMPLIFIER:
The RF amplifier is a three stage amplifier with input and output isolators. The input and output isolators
provide an input and output impedance match and reduce the possibility of instability that could be caused
by an external impedance mismatch.
The circuit boards are a microwave substrate onto which is etched a computer aided designed microstrip
circuit. Incorporated in the microstrip circuit design is a coupler for the RF output detector and a lowpass
filter.
The amplifier is operated in the saturated mode and requires an input level of 10 to 40mW (+10 to
+16dBm) to achieve the rated output level of 12W (+39dBm).
RF TECHNOLOGY, INC.
RF-215D AMPLIFIER INSTALLATION
When installing an RF-215D amplifier caution has to be taken so that the heat generated within the
amplifier is removed via a good thermal connection between the amplifier and the surface it is being
mounted to. The surface the amplifier is to be mounted to has be smooth and free of surface irregularities
and large enough to provide a heat sink for the amplifier. Ideally this surface should be free of coatings
(paint, etc.). Thermal compound has to be used between the amplifiers mounting surface and the surface
it is being mounted to. An optional heat sink is available for certain applications when a mounting
surface is not available that will provide an adequate heat sink for the amplifier.
When installing an RF-215D outdoors the amplifier has to be mounted so that the connectors are facing
down. In ENG truck applications the connectors are to be facing down during operation and to the rear of
the truck then the mast is in the stowed position.
Four 10-32 threaded holes are provided for mounting the amplifier refer to the RF-215D outline drawing
number ASXXXX for the hole pattern.
NOTE: The RF-215D amplifier can be damaged if it is operated without an adequate heat sink and/or air
flow.
Please consult the factory if you have any questions or concerns on installing the RF-215D amplifier.
RF-215D AMPLIFIER SPECIFICATIONS
Frequency Range:
1990 to 2500GHz.
RF Power Output:
12Watts (+41dBm)
RF Power Input Range:
10 to 40mW (+10 to +16dBm)
DC Input voltage Range:
+10.6 to +18VDC
DC Current:
4Amps at +12VDC
Operating Temperature Range:
-30 to +50 Deg. C ( -22 to +122 Deg. F)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:05:21 12:20:35
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:05:21 12:20:37-04:00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools