RMR Management Group 911A 911A Location Calling Device User Manual 2
RMR Management Group 911A Location Calling Device 2
User Manual
9“ USERS + MANUAL 1 Wzy Xpukcr Operl the battery compartment located on the rear ol the device and insert \ . , ‘ three AAA alkaline battenes (included) Take note olthe polanty marklng (+ / e) on case Reattach the battery cover allaunun PwL-rfiunon Press and hold the BATTERY CHECK button located on the rtght hand stde or the 911 Help Noww. The devtce will announce: Battery checklng The devtce ts ready to use trthe tront LED ltght ts green. tithe LED ts not green, venty correct lnsIaHatlun otthe batterles. trthe LED ltght ts red. the battertes are low and should be replaced Batterles must be recycled or disposed ct properly. To call 911. press and hold the whlte and red cross button (+1 on the from ot the device until the device responds with “CaHing 911" and the LED ltght glows blue The devtce wtll connect to a 911 operator it cellular service ts avaltable After connectlng wlth 911 operator. the devlce wIH announce Thls Is a tlve M0 way call trorn emergency pendant with GPS Technology. Press 9 at any ttme to hear the location . .Connecting to the user now." After the 911 operator press 9, the device wtll announce “findlng tocatlon " When the address ls located, the devlce Wl|| announce the address Bank Bauuy (ontvsrttnent ”the calt lalls to comptete, you wltl hear “Dlscohnected, Radial" and the device Witl retry catllng 911 untll an operator ls reached The devlce WIH contlnue to caH 911 untll a connecllon is establlshedt the catl ls canceled or the battery ls depteled. TD dlsconnect. press the CANCEL button on the rlghl hand slde or Walt tor the 911 operator to hang up.(CANCEL button and BATTERY CHECK button are the same one) The 911 operator WIN be able to locate your GPS address by press 9. FCC Warning Any Changes or modifications not expressly approved by the party responSlhle lot compliance could void the user‘s authority to operate the equipment. This device complies with part 15 at the FCC Rules. Operation is suhiect lo the rollcwmg two conditions: (i) This device may not cause harmrul interrerence, and (2) this device must accept any interlerence received, including interterence that may cause undesired cpeiaticn Note. This equipment has been tested and found to comply with the limits for a Class B digital deiiice. pursuant to part is of the FCC Rules These limits are designed to proiiide reasonaole protection against harmrul interlerence in a residential installation This equipment generates, uses and can radiate radio lieouency energy and, it not installed and used in accordance with the instructions. may cause harmful interlerence to radio communications However. there is no guarantee that interlererice Will not occur in a particular ihsmllaticn. llthis equipment does cause harmlul interlerence to radio or television reception, which can be determined by turning the equipment all and on. the user is encouraged to try to correct the inlerference by one or more of the lollowmg measures. iReorien! or relocate the receiVing antenna. ilnclease the separation between the equipment and receiver iconnect the equipment into an outlet on a circuit dilterent lrom that to which the receiver is connected. iconsull the dealer oran experienced radio/TV technician tor help SAR tests are candueted using standard operating positions accepted by the rcc With the deiiice transmitting at its highest certiiied power level in all tested frequency bands, although the SAR is determined at the highest certllied power level, the actual SAR level orthe deiiice while operating can be well tielow the maximum value Before a new model device IS a availabletor saleto the public. it must be tested and certified to the FCC that it does not exteed the exposure limit established by the FCC, Testsroreath deviceare pertormed in positionsand locations (e g. at the earand worn on the oodvias required ovthe rcc. Far body wolrl opevatlorl, (his model device has been tested and meets the FCC RF exposure gu‘ldellneswhen used with an accessory designated lortlils product orwlien used with an accessoryrhat Cunlalns no metal Nonrwmpllance With the above restrictions may result in violation of RF exposure guidelines
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : Administrator Create Date : 2018:02:28 17:14:30+08:00 Modify Date : 2018:03:05 19:12:45-08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : Administrator Title : 未命名 -2 Creator Tool : CorelDRAW X6 Metadata Date : 2018:03:05 19:12:45-08:00 Producer : Corel PDF Engine Version 16.1.0.843 Document ID : uuid:bd39b383-7fd9-4e4a-a740-06697830ea62 Instance ID : uuid:847385b1-32f2-4e28-aaf0-1af0da8ceae4 Page Count : 2EXIF Metadata provided by EXIF.tools