ROULE ELECTRONICS RL-3RF3986I Driveway Alert User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2285069
Application ID	XIS9wpIaGnSge7ehqxbH+w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	79.01kB (987577 bits)
Date Submitted	2014-06-03 00:00:00
Date Available	2014-06-04 00:00:00
Creation Date	2014-03-20 16:41:44
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-06-03 11:22:11
Document Title	Users Manual
Document Creator	Adobe InDesign CS6 (Windows)

Driveway Alert
EN
INSTRUCTION MANUAL
MDRIVE2260214E
Introduction
ENGLISH
Long driveway? Security conscious? Is that car driving up your driveway, or just passing by?
Can’t hear someone knocking on your front door while you’re at the back of your home?
Presenting the Driveway Alert from Swann, the unique system which will let you know when
people are coming to visit!
How does it work?
Basically, there are three parts to the Driveway Alert system.
1.
The Indoor Alarm Receiver works as an alarm buzzer and a doorchime. It monitors for
signals coming from the Passive Infrared (PIR) Motion Sensors and the Doorbell, and
activates an alert in response to that signal. It also features a series of LED indicators
on the front of the unit so you can visually tell where an alert is coming from. The Indoor
Alarm Receiver can be either mounted to a fixed location or completely free standing.
2.
The PIR Motion Sensors enable you to monitor for movement in two zones or areas
surrounding your property. Each contains a miniature radio transmitter, which sends a
signal to the Indoor Alarm Receiver whenever motion is detected. The motion sensors
should be deployed outdoors, where there is a clear view of the driveway or the likely
entry and exit paths that you plan to secure.
3.
The Doorbell enables visitors to send a chime to the Indoor Alarm Receiver so you know
that someone’s waiting at your doorstep. As it is neither water nor weatherproof, it must
be installed in a sheltered location.
Layout
Motion Sensor
Doorbell
Chime Indicator
PIR Sensor Window
Chime Button
Sensor Activity
Indicator
Layout
ENGLISH
Front of the Indoor Alarm Receiver
1. Sensor 1 LED Indicator
2. Doorbell LED Indicator
3. Sensor 2 LED Indicator
Back of the Indoor Alarm Receiver
1. Sensor 1 Select Button
2. Doorbell Select Button
3. Sensor 2 Select Button
4. Battery Compartment
5. Chime Select Button
6. Volume (Low-Medium-High) Slide Switch
7. Speaker
8. Mounting Hook Hangers
Operation Guide
Installing Batteries
ENGLISH
The Indoor Alarm Receiver and Motion Sensors require batteries. These are necessary
for the devices to be able to receive and transmit active wireless signals. For best
performance, use fresh, high quality alkaline batteries.
Note: We recommend changing the batteries in the receiver and sensors every six months.
Indoor Alarm Receiver
•
The Indoor Alarm Receiver requires 3 x AA batteries (not included) to operate.
•
To install batteries, slide off the battery cover on the back of the unit to reveal the battery
compartment and then insert batteries matching the polarity (+ and -) markings inside
the battery compartment.
•
Replace the battery cover until it clicks into place.
Motion Sensors
•
Each motion sensor requires a 9V battery (not included) to operate.
•
To install battery, remove the two screws on the back of the motion sensor securing the
battery compartment cover in place using a small Phillips head screwdriver, attach a
battery to the 9V connector and then place the battery into its compartment.
•
Replace the battery cover. Ensure that it makes complete contact with the silicone seal
lining the battery compartment. If moisture is able to enter the motion sensor, it will
adversely affect performance dramatically.
Doorbell
•
If you need to replace the battery, insert a small flat-head screwdriver into the small
notch on the base of the doorbell and then push against the tab inside to lift the front
cover off.
•
Replace with same type of battery (1 x CR2032 battery). Ensure the battery is secured
properly before refitting the front cover.
Placement of the Motion Sensor
The range of the wireless transmission for the Driveway Alert system is dependent on
local environment (i.e., obstructions, weather, signal interferences, etc) and can be up to
approximately 80 meters (around 263 feet) – take this into consideration when selecting
positions for the motion sensors and make sure you test if the location you place the motion
sensor is in range before fitting in place.
20ft/6m
The motion sensor, under typical conditions, is
designed to detect people and vehicles moving
within an area of approximately 6 meters (around
20 feet) at a 100° angle from the sensor.
For best coverage and to maximize detection,
place the sensor approximately 2m/6ft off the
ground, pointing on a slightly downwards angle.
13ft/4m
6ft/2m
100°
Operation Guide
•
Although the sensors are weather resistant, they are not waterproof – Installing in a
covered area where it is under an awning or eaves is recommended. Exposure to rain
and moisture could adversely affect the performance and durability of the sensors.
•
Any moving heat source can trigger the sensor. For example, a moving shadow on a
sunny day may trigger the sensor, or the sun coming out from behind clouds. False
triggers should be rare, but will occasionally occur.
•
Wandering small animals (such as a cat or similar) can, under some circumstances,
trigger the sensors. Therefore, we suggest that the motion sensors are not suited to
areas where pets are routinely kept.
•
Ideally, the sensor should only see your driveway, and the only moving object(s) in front
of the camera should be the car(s) or person(s) you want to detect.
ENGLISH
Tips & Tricks:
Adjusting the Alarm/Chime Volume
To adjust the volume of the alarm/chime, use the volume control slide switch on the back of
the Indoor Alarm Receiver. There are three settings available: low, medium and high.
Changing the Doorbell Chime
The Indoor Alarm Receiver provides a choice of 16 different chimes.
To change the doorbell chime:
1.
Press the Chime Select button on the back of the Indoor Alarm Receiver. The next
chime is played. Keep pressing the button until you hear a chime you like.
2.
Press and hold the Doorbell Select button on the the back of the Indoor Alarm Receiver
until the Doorbell LED indicator lights up.
3.
Within 10 seconds, press and hold the Chime button on the Doorbell until the chime
indicator stops blinking. The selected chime will now be heard whenever the doorbell
is pressed.
Turning Off/On the Sensor Alarm and Doorbell Chime
Like some peace and quiet for a period of time? You have the ability to put the alarm/chime
for each individual sensor and the doorbell on “silent” mode.
1.
If mounted, remove the Indoor Alam Receiver from the mounting hook.
2.
Press any Sensor 1/Sensor 2/Doorbell Select button on the back of the Indoor Alarm
Receiver once to turn off the alarm/chime from that particular component. You will
hear two beeps from the Indoor Alarm Receiver, indicating that the alarm/chime has
turned off.
3.
To turn the alarm/chime back on, press the corresponding Sensor 1/Sensor 2/Doorbell
Select button again. You will hear a single beep from the Indoor Alarm Receiver,
indicating that the alarm/chime has turned on.
Note: The LED indicators on the front of the Indoor Alarm Receiver will continue to blink
whenever the unit receives a signal from the corresponding sensor or doorchime.
Mounting
ENGLISH
WARNING: When fitting the screws into the wall, make sure you
are not inserting them anywhere near electrical wires, including
wires that may be behind the wall. If you are unsure at all, please
get a professional to check first and install the screws for you.
Indoor Alarm Receiver
There is no requirement to mount the Indoor Alarm Receiver. As it is also completely
freestanding, you may find it more convenient to place it on a shelf or table. One of the
benefits of a battery operated wireless receiver is that if you have a large house, you can take
the receiver with you. No more missing visitors because you were all the way at the back of
the house or by the pool!
If you would like to mount the receiver, you simply
need to screw the mounting hook to a wall using
the four screws provided and then hang the Indoor
Alarm Receiver onto the hook.
Mounting Hook
Motion Sensor
1.
Choose the mounting location and then mark
the screw hole location with a pencil.
2.
Drill the supplied screw into the marked
location, leaving approximately ¼” of the screw
protruding from the mounting surface. You
may need to use a wall plug depending on the
surface.
3.
Hanger slot
Place the sensor’s hanger slot (see opposite)
over the screw and then shift the sensor
downwards to ensure it sits on the screw firmly.
Doorbell
The doorbell can be mounted by sticking it to a wall using the included adhesive strip(s).
1.
Choose the area you want to mount the doorbell - flat, smooth surfaces are ideal.
2.
Peel off the covering of the adhesive strip, and then attach the doorbell to the wall in the
location you want.
Troubleshooting
Problem: My motion sensor isn’t detecting movement.
•
The motion sensor may not be within range of the Indoor Alarm Receiver. Sometimes
obstructions between the sensor and receiver such as walls, metal objects, etc in the
environment can affect the sensor’s functional range.
•
The battery in the motion sensor is weak. It is recommended to replace the battery
every 6 months to maintain optimum performance.
ENGLISH
Solution:
Problem: The sensor LED indicator on the Indoor Alarm Receiver is blinking but I don’t
hear any alarm when my motion sensor is triggered.
Solution:
•
The alarm for the corresponding sensor has been muted on the receiver. See “Turning
Off/On the Sensor Alarm and Doorbell Chime” on page 5 for instructions on how to
turn it back on.
Problem: I keep getting false alarms!
Solution:
•
The sensors use passive infrared to detect changes in temperature so check that there
are no shifting heat sources in view of the motion sensor(s). This includes the obvious
things, such as moving pets or people, but also things such as a moving shadow on
a hot day (such as the shadow of a tree blowing in the wind). Sometimes reflected
infrared heat from the sun is enough to trigger the sensor.
•
If you’ve had the Driveway Alert system installed for some time, then the batteries in
the sensors might be running low, causing erratic behavior.
•
If you’re using the Driveway Alert system in an environment with a high level of
radio ‘noise’ (that is, somewhere with multiple wireless devices in use) then these
interfering signals might be interpreted as the system as alarm signals. This should,
however, be a very rare occurrence.
Problem: The chime doesn’t sound.
Solution:
•
Check the doorbell battery - the chime indicator should light up when the chime button
is pressed. Replace if necessary.
•
The chime has been muted on the receiver. See “Turning Off/On the Sensor Alarm and
Doorbell Chime” on page 5 for instructions on how to turn it back on.
FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Instance ID                     : uuid:b56bd2c4-2a98-4bb2-9867-d986172d854e
Original Document ID            : adobe:docid:indd:7c855f6f-cb75-11df-8f67-ded6e41b7466
Document ID                     : xmp.id:271F3833F1AFE31182EE981C1FBB6087
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:251F3833F1AFE31182EE981C1FBB6087
Derived From Document ID        : xmp.did:EA7D076099A9E311A67EFF60D9D09314
Derived From Original Document ID: adobe:docid:indd:7c855f6f-cb75-11df-8f67-ded6e41b7466
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:03:20 16:41:44+11:00
Create Date                     : 2014:03:20 16:41:44+11:00
Modify Date                     : 2014:06:03 11:22:11+08:00
Metadata Date                   : 2014:06:03 11:22:11+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Has XFA                         : No
Page Count                      : 8
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools