RSI VIDEOTECHNOLOGIES MV50 Outdoor Motion Viewer User Manual manual1

Download:
Mirror Download [FCC.gov]
Document ID	2716679
Application ID	Dmr9pwA14o/AnnOpjk67Kw==
Document Description	manual1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	101.54kB (1269245 bits)
Date Submitted	2015-08-17 00:00:00
Date Available	2015-08-17 00:00:00
Creation Date	2015-07-03 15:32:10
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2015-07-03 15:32:14
Document Title	manual1
Document Creator	Adobe InDesign CC 2015 (Windows)

OMV OUTDOOR MOTION VIEWER
INSTALL SHEET
DOC. - REF. 213-OMV
VERSION : JULY 2015
Product Summary
The OMV 210/611/712 MotionViewer is a wireless, battery
operated, motion activated or electrically activated outdoor
camera designed for use in Videofied ® security systems.
• Powered by 4 Lithium batteries for extended battery life.
• 90° wide lens (by default).
• Provided optional lenses: vertical and horizontal curtain, long
range beam (up to 18m).
• 4 infrared LEDs for 12m night vision.
• Standard detection distance (up to 12 meters).
• Fully
weatherproof
(IP65)
and
temperature
resistant
(-20°C/+60°C).
• Tilt sensor tamper.
• Transmits check-in/status signal every 8 minutes.
• 3 wired programmable inputs (2 supervised).
• 1 wired programmable output triggered on detection.
Installation Guidelines
For easier installation, programming and RF testing should be done to check for
good communication between the control panel and all system devices before
mounting system devices.
Install the detector and other system devices in the order of the following steps:
> Programming/RF
Testing - program detector and all other devices into the
control panel and test RF communication from each intended device location to
the control panel.
> Mounting - mount detector at the tested location.
Mounting
> Use proper tools and hardware.
> Mount camera between 2.5 m to 4 m height.
> The OMV MotionViewer detection distance may vary depending on weather
and the detector mounting (height, tilt). The OMV is not suitable to protect an
area, it needs to be used to protect an access point or any property.
> Mount detector aimed toward the spot to protect.
> In order to reduce false alarms, do not aim the detector toward vegetation, a
road, or unlimited space.
> Do not cover the Fresnel lens. Use only
the provided masking kit to block
detection towards specific spots (trees, bushes, etc.).
MB110 Mounting kit for
Outdoor MotionViewer
INSTALL SHEET
OMV OUTDOOR MOTION VIEWER
Programming/RF Testing/Mounting
The following provides summarized steps for device programming,
testing, and mounting. For complete details, refer to the control panel
installation manual.
Separate the base from the box
2 Install 3 3.6V LS14500 SAFT
batteries observing correct polarity.
3 Put control panel into
Programming/Configuration mode.
programmed
4 Using
alphanumeric
keypad,
proceed
through menus until the display shows
ADD A NEW DEVICE.
Press OK/YES to end radio range test then press ESC/NO.
10
The keypad displays :
AREA ALLOCATION :
AREA : 1
Press either arrow button repeatedly until desired area number appear
then press OK/YES. By default all devices in Area 1 are automatically
delayed.
11
Screw
5 Press OK/YES. the display shows PRESS PROGRAM BUTTON OF
DEVICE.
The display shows NAME + LOCATION:
Enter appropriate device name/location (up to 16 characters), then
press OK/YES. The display shows the device number and name for
your verification.
Press and release program button on
the OMV MotionViewer.
12 Mount the DCV on the wall or the MB 110 Mounting kit. Follow
the installation guidelines shown in page 1.
The OMV PIR flashes.
13 Press OK/YES. The display shows FUNCTIONAL DEVICE TEST?
Press OK/YES and verify camera operation. For example, wave your
hand in front of the sensor to activate its LED indicating detection.
7 Wait for keypad display to show
CAMERA(1 - 25) PROGRAMMED. Press
OK/YES, the display shows RADIO
RANGE TEST? Press OK/YES again. The
camera LED starts flashing and keypad
display shows RF TEST.
14
IN IT button
Take the OMV camera to its intended mounting location and
make sure LED flashes continuously or you receive a 9/9 indicating
good communication with the control panel.
Press OK/YES to end detection verification.
15 The display shows OPERATION COMPLETED or ADD A NEW
DEVICE? Press YES/OK. Repeat steps 1 – 14 for remaining cameras.
16
When finished, exit from configuration mode.
OMV OUTDOOR MOTION VIEWER
INSTALL SHEET
Mounting Recommendations
For optimal use, OMV MotionViewer mounting shall respect the following recommendations.
Mounting height :
Recommended mounting height should be comprised between 2.5m and 3m.
When you install the MotionViewer higher, the detection distance is raised. However the sensitivity is
reduced and the blind area under the MotionViewer is larger.
When you install the MotionViewer lower, the sensitivity is raised and the blind area under the detector is
reduced. However the detection distance will be reduced.
Tilt :
The detector should be tilted 3° to 5°
Raising or reducing the tilt, even slightly, has a big impact on the detection distance and on the blind area
under the MotionViewer.
Example : Increasing the tilt from 5° to 15 ° can reduce the detection distance up to 33%, that could translate
into a loss of detection distance to 4 meters
Blind Area
Max detection distance
OMV OUTDOOR MOTION VIEWER
INSTALL SHEET
Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit
English
Français
Deutsch
• Remove the batteries before any
maintenance !
• WARNING, there is a risk of explosion if a battery
is replaced by an improper model !
• Observe polarity when setting up the batteries!
• Do not litter the batteries when they are used!
Dispose of it properly according to Lithium Metal
requirements
• Retirez les piles avant toute opération de
maintenance !
• Attention ! Il y a un risque d'explosion si la batterie
utilisée est remplacée par un mauvais modèle !
• Respectez la polarité lors de la mise en place des
piles !
• Ne jetez pas les batteries usagées !
Ramenez-les à votre installateur ou à un point de
collecte spécialisé.
• Batterien vor jeglichen Wartungsarbeiten
entfernen!
• Vorsicht, es besteht Explosionsgefahr, wenn eine
Batterie durch eine Batterie falschen Models
ersetzt wird!
• Achten Sie beim Einsetzen der Batterien auf die
Polung!
• Entsorgen Sie Batterien nicht im normalen
Haushaltsmüll! Bringen Sie Ihre verbrauchten
Batterien zu den öffentlichen Sammelstellen.
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC
authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la Partie 15 des règlementations de la FCC et avec la norme RSS-210 de l’Industrie Canadienne.
Son fonctionnement est soumis aux deux conditions suivantes :
Cet appareil ne doit pas causer d’interférences nuisibles et
Cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable.
OMV OUTDOOR MOTION VIEWER
INSTALL SHEET
ELECTRICAL PROPERTIES
W, XL, XT, XV and their variants
Panel compatibility
Power requirements
DETECTION PROPERTIES
Type C - 4 Lithium batteries 3,6 V LS14500
Battery life
Infrared detection specifications
Technology
Passive infrared DSP
Type
Dual element sensor
Detection lens
Standard usage (up to 5 videos per month)
• 90° on 12m max (by default)
• 80 cm curtain for 12m distance (vertical or horizontal)
• 1m diameter beam for 18m distance (long distance beam)
4 years
High usage (about 30 videos per month)
2 years
Tamper detection
RADIO PROPERTIES
Tilt
RF S2View® technology
Radio type
Spread spectrum bidirectionnal
Operating frequency
• 868MHz - OMVC 210 (Europe, Africa, Asia)
• 915 MHz - OMVC 6111 (USA, Canada, South America)
• 920 MHz - OMVC 712 (Australia, South America)
AES encryption algorithm
Transmission security
Supervision
Radio antenna
Position change, shock, wall and cover tamper
BOX
Physical properties
Material
Dimensions
Weight
Radio, batteries, tamper, position
Environmental data
Integrated
Operating temperature
Max. relative humidity
VIDEO PROPERTIES
Polycarbonate UL94
130,5mm x 102,44mm x 141,5mm
261g (without batteries)
-20°/+60°C
95%, without condensing
IP 65
Protection marking
Camera
90°
Angle
CMOS
Sensor type
Daylight video
Programmable : Color or B&W
Night video
Automatic black & white infrared
Automatic with 4 IR LEDs
Infrared illumination
Up to 12m
Infrared illumination distance
Installation / Mounting
Mounting height
2.5m to 4m
Mounting angle
Mounting
5° to 10°
Use mounting kit (sold separately)
STANDARDS AND CERTIFICATIONS
Video
MJPEG-WMV, MJPEG-DIFF
Video format
5 images per second
Frame rate
Video duration
EN50131-4
Grade 2 -- Type W
Programmable (10 seconds by default)
NF EN50131-4
2009 Grade 2 -- Type W
QVGA (320x240)
NF EN50130-4
2011
SQ or HQ
NF EN50130-5
2011 Environment class II
Video resolution
Quality
Average video file size
220 kb
Image
Format
Resolution
Quality
Average image file size
www.videofied.com
Matériels de sécurité electronique, détection d’intrusion
DISPOSITIF D’ALARME SONORE
JPEG
VGA (640x480)
HQ or SQ
8 kb
Marque commerciale
Référence produits
Videofied
OMVC 210
N° de certification
Organisme certificateur :
CNPP Cert.
Route de La Chapelle Réanville CS22265
F—27950 SAINT MARCEL
Tel : +33(0)2.32.53.63.63
Fax: +33(0)2.32.53.64.46
Sites Internet : http://www.cnpp.com
Email : certification@cnpp.com
Organisme certificateur :
AFNOR Certification
11, rue François de Pressensé
93571 Saint Denis La Plaine Cedex
Tel : +33(0)1.41.62.80.00
Fax: +33(0)1.49.17.90.00
Sites Internet : http://www.afnor.org
et http://www.marque-nf.com
E-mail : certification@afnor.org

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c067 79.157747, 2015/03/30-23:40:42
Create Date                     : 2015:07:03 15:32:10+02:00
Metadata Date                   : 2015:07:03 15:32:14+02:00
Modify Date                     : 2015:07:03 15:32:14+02:00
Creator Tool                    : Adobe InDesign CC 2015 (Windows)
Instance ID                     : uuid:fec82cbf-362b-4211-97b2-9d54f4178eb1
Original Document ID            : xmp.did:1a7ab4ca-f8fa-be43-a670-8943a9c232b1
Document ID                     : xmp.id:afb60a89-f8a6-6546-a183-bd75409fad9a
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:ddcb92e6-351c-7c40-bac7-f5ff872473dc
Derived From Document ID        : xmp.did:7224cb9f-78c8-6a41-bc4a-c92d4f1e2b67
Derived From Original Document ID: xmp.did:1a7ab4ca-f8fa-be43-a670-8943a9c232b1
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Windows)
History Changed                 : /
History When                    : 2015:07:03 15:32:10+02:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 5
Creator                         : Adobe InDesign CC 2015 (Windows)

EXIF Metadata provided by EXIF.tools