RSI VIDEOTECHNOLOGIES SE50 Outdoor Siren User Manual Installation sheet

RSI VIDEOTECHNOLOGIES Outdoor Siren Installation sheet

Installation sheet

www.videofied.comProduct SummaryThe Outdoor Siren SE651 is a wireless siren designed for use in Videofied security systems. The siren includes the following features: > Totally wireless, battery operated.> Dual tamper function provides detection for both wall and cover tamper.> Transmits check-in/status signal every 8 minutes.Installation GuidelinesFor easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices. Install the siren and other system devices in the order of the following steps:> Programming/RF Testing - program siren and all other devices into the control panel and test RF communication from each intended device location to the control panel.> Mounting - mount siren at the tested location.Programming/RF TestingThe following provides summarized steps for device programming and testing. For complete details, refer to the control panel installation manual.1 Remove four cover screws, separate cover from siren and install batteries. 2 Put control panel into programming/ configuration mode.3 Using a programmed alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE.4 Press Yes. The display shows PRESS PROGRAM BUTTON OF DEVICE.5 Press and release program button on siren using a paper clip end. The siren LED flashes. Wait for keypad display to show SIREN (1 - 24) RECORDED. To the question “REMOTE CONTROLLED?” press: No to be automatically controlled by the alarm panel Yes if the siren is controlled by the monitoring station. 7 Press Yes. The display shows RADIO RANGE TEST? Press Yes again. The siren LED starts flashing and keypad display shows TEST IN PROGRESS.8 Take the siren to its intended mounting location and make sure LED flashes continuously, indicating good communication with control panel.9 Press Yes to end radio range test, then press Esc/No.10 The display shows ADD A NEW DEVICES? Repeat steps 4 - 8 for remaining sirens.11 When finished, exit from configuration mode. 6ScrewsProgram ButtonPRODUCT INSTALLATION SHEETOutdoor Siren SE6512204-SEOIS February 2012Made by RSI VIDEO TECHNOLOGIES
Mounting> Use proper tools and hardware for mounting the unit.> Mount outdoors under eves to help prevent direct contact from elements.> Mount on front of structure where strobe light is clearly visible to responding authorities.1 Remove batteries.2 Hold unit up against mounting surface and mark the three mounting holes.3 Drill pilot holes and install anchors where needed.4 Place unit on mouning surface so mounting holes line up with pilot holes/anchors and secure unit with appropriate screws.5 Install batteries, observing correct polarity.6 Place the flash wire of the cover to the siren.7 Attach front cover.Electrical DataPanel Compatibility XL, Visio, XT, XTIPPower requirements Four 1.5 V Alkaline Batteries Nominal Voltage 6V Low Battery Limit 4.8V Battery type Energizer Alkaline D cell - LR20 Battery life Up to 4 yearsRF technology S2View®Radio type Spread Spectrum BidirectionalOperating frequency 915 MHzTransmission security AES encryption algorithmSupervision Polled signal every 8 minutesAntenna IntegratedTamper detection Wall and cover tamperedSpeaker impedance 4 ohmsOutput level 105 dB @ 1 meterOutput duration Configured in Control PanelFlash type Strobe light tubeFlash duration Matches Programmed Siren LengthFlash sequence Four flashes/secOperating temperature -30°/+60°C (-20°/+140°F) Maximum relative humidity 90%, non-condensingApprovals FCC Part 15C Physical DataMaterial ABS—ULV0Dim ensions 227 mm x 166 mm x 80 mm (LxWxD): 9 in. x 6-1/2 in. x 3 in. Weight 880 g/31 oz. (without batteries)Installation/MountingUnit/Base Four screws secure unit to base; three screws secure unit base to mounting surface.www.videofied.comMounting HolesINSTALLATION DATA SHEETOutdoor Siren SE651
EMEA SALES23, avenue du Général Leclerc92340 BOURG-LA-REINEFRANCEHotline: +33 (0)820 846 620Fax: +33 (0)1 82 69 80 10© 2011 RSI VIDEO TECHNOLOGIES. VIDEOFIED® is a Registered Trademark of RSI VIDEO TECHNOLOGIES. S2View® is a registered trademark of RSI VIDEO TECHNOLOGIES. Specications subject to change without notice.USA SALES4455 White Bear Parkway, Suite 700White Bear Lake, MN 55110USAHotline: +1 877 206 5800Fax: +1 651 762 4693 www.videofied.comOutdoor Siren SE651 PRODUCT INSTALLATION SHEETFCC Regulatory Information for USA and CANADAFCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC authorization to operate this equipment.FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Navigation menu