RSI VIDEOTECHNOLOGIES UV50 Outdoor universal viewer User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	3131082
Application ID	gtcuM8y1TlYX8Jduy1A9Yw==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.49kB (406085 bits)
Date Submitted	2016-09-12 00:00:00
Date Available	2016-09-12 00:00:00
Creation Date	2016-06-22 15:53:41
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2016-06-22 15:53:42
Document Title	manual
Document Creator	Adobe InDesign CC 2015 (Windows)

OUV OUTDOOR UNIVERSAL VIEWER
INSTALL SHEET
DOC. - REF. 213-OUV
VERSION : JUNE 2016
Product Description
The OUV 200/601/702 module is a wireless outdoor camera
activated by a connected detector. It is designed for use in
Videofied ® security systems.
• Polyvalent 90° infrared camera
• 4 infrared LEDs for extended night vision
• Protection marking IP54
• Température resistant (-25°C/+70°C)
• Transmits check-in/status signal every 8 minutes
• 8-pin control connector
Installation Guidelines
For easier installation, programming and RF testing should be done to check for good communication between the control panel
and all system devices before mounting system devices.
Install the detector and other system devices in the order of the following steps:
> Programming/RF Testing - program detector and all other devices into the control panel and test RF communication from each
intended device location to the control panel.
> Mounting - mount detector at the tested location.
Mounting instructions
> The module is mounted through 2 backside screw threads (2mm x 7,5 mm).
> Plug the connector to the detector (the use of a short cable is permissible).
> Mount the detector according to the manufacturer recommendations.
OUV OUTDOOR UNIVERSAL VIEWER
INSTALL SHEET
Programming/RF Testing/Mounting
The following provides summarized steps for device
programming, testing, and mounting. For complete details,
refer to the control panel installation manual.
Put control panel into Programming/Configuration mode.
2 Using a programmed alphanumeric keypad, proceed
through menus until the display shows ADD A NEW DEVICE.
3 Press OK/YES. the display shows PRESS PROGRAM
BUTTON OF DEVICE.
4 Apply a voltage on the OUV programming pin (6) through
the connected detection device par l’intermédiaire de
l’équipment connecté.
The OUV blinks.
5 Wait for keypad display to show CAMERA(1 - 25)
PROGRAMMED. Press OK/YES, the display shows RADIO
RANGE TEST? Press OK/YES again. The camera LED starts
flashing and keypad display shows RF TEST.
6 Take the OUV module to its intended mounting location
and make sure LED flashes continuously or you receive a 9/9
indicating good communication with the control panel.
Press OK/YES to end radio range test then press ESC/NO.
The keypad displays :
The display shows NAME + LOCATION:
Enter appropriate device name/location (up to 16 characters),
then press OK/YES. The display shows the device number and
name for your verification.
10 Install the OUV and its detector. Follow the detector
manufacturer mounting instructions.
11 Press OK/YES. The display shows FUNCTIONAL DEVICE
TEST? Press OK/YES and verify camera operation. The
activation of the LED will determine the detection field.
12 Press OK/YES to end detection verification.
13 The display shows OPERATION COMPLETED or ADD A
NEW DEVICE? Press YES/OK. Repeat steps 1 – 12 for remaining
cameras.
14 When finished, exit from configuration mode.
AREA ALLOCATION :
AREA : 1
Press either arrow button repeatedly until desired area number
appears then press OK/YES. By default all devices in Area 1 are
automatically delayed.
Pin
Name
Function
Notes and setting
Vcc
Input voltage
2.8 to 5 VDC
GND
Ground
0V
Detect
Intrusion detection
State 1 (>2VDC) during 100 ms while powering the OUV
Trouble
Communication lost
Armed
System armed
Config
Programming button
Ext-trouble
Problem on the connected detector
IR-ON
Infrared illumination activation
The connected detector must ignore that pin at startup
State 0 (<0.5VDC) during 100 ms while powering the OUV
INSTALL SHEET
OUV OUTDOOR UNIVERSAL VIEWER
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the
FCC authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance of 20 cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
L’appareil ne doit pas produire de brouillage, et
2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
OUV OUTDOOR UNIVERSAL VIEWER
INSTALL SHEET
ELECTRICAL PROPERTIES
Panel compatibility
VIDEO PROPERTIES
W, XL, XT, XV and their variants
8-pin connector
Power
2.8VDC to 5VDC
Power voltage
Power consumption
Average current consumption
85 μA
Standby current consumption
< 15 μA
Max current consumption
350 mA
Night video
Automatic black & white infrared
Automatic with 4 IR LEDs
Infrared illumination
Up to 12m
Infrared illumination distance
MJPEG-WMV, MJPEG-DIFF
5 images per second
Programmable (10 seconds by default)
Video duration
QVGA (320x240)
Video resolution
Operating frequency
• 868MHz - OUV 200 (Europe, Africa, Asia)
• 915 MHz - OUV 601 (USA, Canada, South America)
• 920 MHz - OUV 702 (Australia, South America)
220 kb
Average video file size
Image
AES encryption algorithm
Radio, batteries, tamper, position
Integrated
Radio antenna
Daylight video
Programmable : Color or B&W
Frame rate
Spread spectrum bidirectionnal
Supervision
CMOS
Sensor type
Video format
RF S2View® technology
Transmission security
90°
Angle
Video
RADIO PROPERTIES
Radio type
Camera
JPEG
Format
VGA (640x480)
Resolution
8 kb
Average image file size
STANDARDS AND CERTIFICATIONS
BOX
Physical properties
868MHz (OUV 200)
Polycarbonate and elastomer
Material
43 mm x 20 mm x 26.6 mm
Dimensions
Compliant with the annex IV of the R&TTE Directive 1999/5/EC
12g
Weight
915MHz (OUV 601)
Environmental data
Operating temperature
Max. relative humidity
-25°/+70°C
95%, without condensing
Part 15C
USA FCC
RSS-247 Issue 1
Canada IC
IP 54 / IK 06
Protection marking
920MHz (OUV 702)
AS/NZS4268
Australia RCM
This symbol on the product or on its packaging indicates that this product should not be treated as household
waste. It must be handed over to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health. The recycling of materials will help to conserve natural
resources.
For more information about recycling of this product, please contact your local municipality, your waste
disposal service or the company that installed the product.
EMEA SALES
23, avenue du Général Leclerc
92340 BOURG-LA-REINE
FRANCE
E-Mail : emeasales@rsivideotech.com
www.videofied.com
North American Headquarters
1375 Willow Lake Blvd, Suite 103
Vadnais Heights, MN 55110
USA
E-Mail : usasales@rsivideotech.com
The EC declaration of conformity of
this product is available by flashing
that QR code :

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : fr-FR
XMP Toolkit                     : Adobe XMP Core 5.6-c111 79.158366, 2015/09/25-01:12:00
Create Date                     : 2016:06:22 15:53:41+02:00
Metadata Date                   : 2016:06:22 15:53:42+02:00
Modify Date                     : 2016:06:22 15:53:42+02:00
Creator Tool                    : Adobe InDesign CC 2015 (Windows)
Instance ID                     : uuid:752e6b54-6456-4cd7-8b4c-c4192c0f99e0
Original Document ID            : xmp.did:1a7ab4ca-f8fa-be43-a670-8943a9c232b1
Document ID                     : xmp.id:af621f51-6ddf-af49-95d9-6a5776e0a5f3
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:7b4bfa58-fc55-644b-aebd-bae555f3dc4f
Derived From Document ID        : xmp.did:7224cb9f-78c8-6a41-bc4a-c92d4f1e2b67
Derived From Original Document ID: xmp.did:1a7ab4ca-f8fa-be43-a670-8943a9c232b1
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Windows)
History Changed                 : /
History When                    : 2016:06:22 15:53:41+02:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 4
Creator                         : Adobe InDesign CC 2015 (Windows)

EXIF Metadata provided by EXIF.tools