RSI VIDEOTECHNOLOGIES XT01 Control panel User Manual Installation Manual for XT XTX XTO series
RSI VIDEOTECHNOLOGIES Control panel Installation Manual for XT XTX XTO series
Installation Manual for XT-XTX-XTO series
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1681462 |
| Application ID | eMrJvu1fdVomM85QYI5Qaw== |
| Document Description | Installation Manual for XT-XTX-XTO series |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 327.22kB (4090232 bits) |
| Date Submitted | 2012-04-22 00:00:00 |
| Date Available | 2012-04-22 00:00:00 |
| Creation Date | 2012-04-02 11:13:13 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2012-04-02 11:13:13 |
| Document Title | Installation Manual for XT-XTX-XTO series |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | Andrew Opp |
Document #2000-XTIN COMPLETE SETUP AND PROGRAMMING MANUAL FOR XT610/XTX610/XTO610 GPRS PANELS *A Videofied CMA601 / XMB611(June 2011) Alphanumeric Keypad or Frontel TMT2 is required for programming and maintenance* CMA601 XMB611 4455 White Bear Parkway White Bear Lake, MN 55110 877-206-5800 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Table of Contents FCC Guidelines Page Basic Guidelines Introduction Initial Programming 6-14 Entering Badges and Access Codes 15 Choosing Siren Options 16 Testing to Central Station 17 Disabling Monitoring 18 Testing GPRS Level 19 Testing Device RF Level 20 Connecting a GPRS Antenna 21 Arming Input Wiring Diagram 21 Programmable Input Configuration 22-24 Programmable Output Configuration 25-27 Configuring Scheduling 28-30 Enabling External RF Antenna 31 Mounting XT/XTX 32 Mounting XTO 32-33 Troubleshooting 34-36 Central Station not getting Video 34 Central Station not getting any signals 35 Panel saying Connected with Monitor Station 35 Unable to record device or getting ‘Pairing Failure’ error 36 After Initial Programming Flow Chart 36-41 Addendum 42 2|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Regulatory Information for USA and Canada FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization to operate this equipment. FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Basic Setup Guidelines for Installation and Programming SETUP AND PROGRAM 1) Obtain the account number, IP address, and port number from the Central Station. 2) Activate the SIM card and obtain the APN code, username, and password by calling your cellular provider. *Note: Do step 1 and 2 the day before the install. 3) Setup and program the system in the office or in your vehicle. DO NOT MOUNT THE DEVICES. (Page 4-12) 4) Add user codes and or badges after initial programming. (Page 13) 5) Silence the siren before you set the alarm for testing. (Page 15) 6) Arm the system and send one alarm signal and video to the central station. Call the central station and make sure they received the signal. (Page 16) *Note : Before deploying the system you will want to disable monitoring so that signals are not sent until you are ready to send them. (Page 14) DEPLOYING THE SYSTEM ON SITE 7) Put the panel where you want to mount it and run the GPRS test to make sure you are receiving good cell signal. If you get 3/5 or better, mount the panel. If not, you will need to move the panel and run the test again.* (page 17) 8) Now you are ready to deploy the devices. Use your keypad to run the RF test for each device. If you get a 9/9 for your RF test on the first device, then mount it. If not, you will need to move the device to get optimal signal.* (Page 18) *Note: If you are not getting an appropriate GPRS or RF level, you can add an external antenna for either signal. (Not available for the XL600) *Note: Re-enable monitoring before you send signals (Page 14) 8.5) If you are currently using TMT Installer to program the system you can take still pictures from each MotionViewer using the software. See TMT Installer Users Manual available on support.videofied.com. 9) Once you have everything mounted, you are ready to arm the system and set off each device. Make sure you stand in front of each MotionViewer for 10 seconds so the central station has some video to look at. (Page 16) 10) After you have sent signals to central station, call to verify. The following pages will go through each one of these steps and, if you have any issues, you cannot resolve, please feel free to call technical support at 1-651-855-7800 EXT 45, 1-877-206-5800 EXT 45 or you can reach live support chat and additional technical notes at support.videofied.com. Sleeping mode and Wake-up on the CMA601: Most of the time, the keypad is in a sleeping mode (backlight off). This mode is automatic after 30 seconds of inactivity. When you press a button the keypad wakes up. The first touch on the pad that wakes it up will not be a registered command and will only wake up the keypad. 4|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Introduction: Description: The XT series control panel is a Videofied wireless, battery operated hybrid alarm system. It is designed for residential, small business and commercial security applications. The XT provides integrated Video Verification over GPRS. The XT has programmable inputs and outputs. XT also features mapping where an external input can be used to generate a video clip from a MotionViewer. Internal RF range and GPRS range can be enhanced using external antennas. Supervised Wireless Technology: The XT, along with all Videofied devices, uses the patented S2View® - Spread Spectrum, Videofied, Interactive, AES Encrypted Wireless technology, providing optimum signal integrity and security. The bi-directional RF communication path between all devices and the system control panel guarantees high signal reliability. Integrated antennas eliminate protruding wires or rods, which are difficult to install, unsightly to consumers and potentially troublesome if damaged. The panel supervises every device (excluding the remote key fob) to validate current open/close state, tamper condition, serial number, date of manufacture, firmware revision, and battery status. In order for an installation to be UL compliant you must follow the specifications in the table below: Type Audio Audio Delays Specifications When a MotionViewer is installed on the system you may not have the siren sound for less than 60 seconds If no MotionViewer is installed on the system you may not have the siren sound for less than 240 seconds When a MotionViewer is installed on the system the Entry delay must be 45 seconds Location In Manual Page 26 Page 26 Page 9 5|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS SETUP MANUAL FOR XT SERIES GPRS PANEL *THIS SYSTEM REQUIRES A CMA601/XMB611 or TMT INSTALLER SOFTWARE FOR PROGRAMMING* XT Initial Programming Open the Control Panel Using a #1 Phillips screwdriver, remove the 2 screws holding the cover on. The cover will fold off the panel like a book with the curved side acting like the binding. The same technique is used when placing the cover back onto the unit. When removing the XTO cover, pull straight off, do not slide it. 6|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS *The SIM card must NOT be inserted or removed while the panel is powered* Install the SIM card Slide SIM card into the slot. Make sure it is aligned correctly. Powering the Panel **THE CONTROL PANEL MUST BE CONNECTED TO AN EXTERAL POWER SUPPLY WHEN SMS FEATURE IS ACTIVE** Option 1: PP1 4 x LSH20 SAFT Lithium D-Cell Option 2 4 x E95VP Alkaline D-Cell + 12v 2amp DC Class 2 power supply (not supplied) Used for Standalone or Xtender mode without Programmable Inputs, Programmable Outputs, or SMS LSH20 Specifications: Operating Temp: -76°F to +230°F Storage Temp: Dry, Ventilated, 86°F Max LSH20 Technical Specifications Nominal Voltage 3.6 V Open Circuit Voltage 3.67 V Nominal Capacity 9.3 Ah Used for Standalone or Xtender mode where Programmable Inputs/Mapping, Programmable Outputs, or SMS will be used E95VP Specifications: Operating Temp: 0°F to 130°F E95VP Technical Specifciations Nominal Capacity 8900 mA hours Nominal Voltage 1.5 V Power Supply Requirements Output Voltage (volts) 12 Output Current (mA) 2000 Class 2 (For UL Certifications Compliance) 7|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS WARNINGS: 1. DO NOT USE ALKALINE BATTERIES IF INSTALLING AN XTX/XTO GPRS BELOW 30° F, YOU MUST USE OPTION 1: PP1. 2. DO NOT INSTALL A TRANSFORMER WHEN USING OPTION 1 (LITHIUM BATTERIES). Obtaining XMB Keypad Special Characters Obtaining CMA Keypad Special Characters 8|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS XT Programming Reset the XT Panel: Press and hold programming button () for 10sec until the Indicator LED blinks twice Press and instantly release the programming button (). The indicator LED will blink once. The panel is now in ‘Learn Mode’ for the CMA601 keypad. *Note: If you are having issues pairing the keypad to the panel, please refer to the troubleshooting section. Insert all three batteries into the CMA601 and press both the ESC/NO and CLR keys at the same time and release. The indicator LED on the keypad will blink rapidly. CMA Programming Device/Keypad RSI (c)2005 www.RsiAlarm.com or <======XX======> CLR & ESC/NO KEYPAD 1 RECORDED YES Other languages are available by scrolling with arrows. ITALIANO, NEDERLANDS, DEUTSCH, CASTELLANO, SVENSKA, PORTUGUES, FRANCAIS Press YES for the selected one. <- LANGUAGE : -> ENGLISH or for language YES to apply selection 9|Page 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS The Radio Range test should be run during device recording to ensure proper pairing with the control panel. This test is the communication strength between the device and the control panel. The keypad will display a real time RF level for the device that is being tested. This test will run until stopped and should be run for at least 30 seconds to receive accurate results. RADIO RANGE TEST ? YES RF TEST x/9 The RF level must be 9/9 for reliable transmission. RADIO RANGE TEST ? YES ESC/NO ENTER THE INSTALLER CODE Wait while the screen changes From here until the end of initial programming you will not be able to step back to a previous parameter. All parameters can be changed after initial programming has been completed. 4 TO 6 DIGITS THEN YES INSTALLER CODE: Use the Alphanumeric Keypad to enter the Installer Code *This code is important to keep track of. There is no back door to the system INSTALLER CODE: xxxx CONFIRM CODE RE-ENTER CODE YES CONFIRM CODE xxxx You may name the installer code using the Alphanumeric Keypad. If you leave the name blank it will default to ‘ACCESS 1’ CODE NAME : YES ACCESS 1 ENTRY COMPLETE Wait while the screen changes ADJUSTING TIME AND DATE DATE (Year) : 09/ / Use the or DATE (Year) : 10/ / to set the Year DATE (Month) : 10/01/ Use the or to set the Month YES DATE (Month) : 10/11/ 10 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS YES DATE (Day) : 09/06/01 Use the or DATE (Day) : 09/06/03 to set the Day YES TIME (HOUR) : 00:00 Use the or TIME (HOUR) : 10:00 to set the Hour – The system uses a 24 hour clock. DATE (Minutes) : 10:00 Use the or DATE (Minutes) : 10:53 to set the Minutes YES 03/06/09 10:53 ENTRY COMPLETE YOU MUST ALWAYS CHOOSE ‘YES’ Use the Alphanumeric Keypad to enter in a 4-8 digit account number provided by the Central Station CONNECTED TO MONITOR.STATION? YES ACCOUNT NUMBER? ACCOUNT NUMBER:99865123 Other periods are available: 48 hours, 24 hours, 12 hours,1 hour, No Test Use arrows for the selection and press YES to confirm. *We suggest at least a 24 hour test PERIODIC TEST: 24 HOURS or and Use the arrow keys + YES to choose the Hour and Minute the periodic test will happen. for period YES to apply YES selection TEST HOUR: 00:00 TEST MINUTE: 00:00 11 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS CODE/STATE modification These are the default transmitted events: Device Alarm Alert Alarm Initialization Not Transmitted Panel Batteries Alarm/End AC Power Alarm/End Phoneline Fault Not Transmitted Tamper Alarm/End Device Batt. Alarm/End Radio Jamming Not Transmitted Supervision Alarm/End Periodic Test Alarm Wrong Codes Not Transmitted Duress Code Alarm Alarm Memory Not Transmitted Arm/Disarm Not Transmitted CODE/STATE MODIFICATION ? YES TRANS. STATE MODIFICATION ESC/NO List of all events If you would like to change the state press YES and use the or to toggle between: Alarm – Appearance Alarm/End – Appearance and Restoral Not Transmitted – Not Transmitted ESC/NO AREAS CONFIGURATION If you would like the default press ESC/NO Wait Use the Alphanumeric Keypad to name the area and press YES. AREA NAME 1: Repeat for all four areas. If you want to keep the default area names press the ESC/NO key. By default Area 1 is a delay area and Area 2, 3, & 4 are instant areas. ARMING OPTION: Your choice will depend on how you are arming the system. From the host: Will make the XT a piggyback/xtender system that arms and disarms off the latching of 9-12v on the arming inputs. ARMING OPTION: Standalone ARMING OPTION: From the host Standalone: Will make the XT a solo system controlled by arming and disarming using Videofied peripheral devices. Other values are available: 2 min, 1 min, 45 sec Use the arrows for the selection and YES to confirm. Other values are available: 2 min, 1 min, 45 sec, 30 sec, 15 sec Use the arrows for the selection and YES to confirm. EXIT DELAY: 45 Sec Go to Page 10 if you will be choosing this option ENTRY DELAY: 15 Sec Go to Page 11 to continue with standalone programming 12 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Using the control panel as a Xtender system will only be able to arm and disarm by latching 9-12v to one of the two inputs. Arming input 1 will control the arming and disarming of devices in areas 1 and 2. Where devices in area 1 are subject to the Entry Delay. Arming input 2 will control the arming and disarming of devices in areas 3 and 4. Where devices in area 3 are subject to the Entry Delay. ARMING OPTION : From The Host Mode Slow : Used for following the arming and disarming of the host system. This will arm each device one at a time conserving battery life. Mode Fast : Used to instant arm all devices while sacrificing battery life. MODE: Slow YES YES MODE: YES Fast YES ENTRY DELAY Enter the value for your Entry Delay up to 255 seconds and press YES. VALUE:(0-255) (000): YES By entering a value using the keypad, up to 600 seconds, the transmission of any event will be delayed that many seconds. Enter the value you would like for the Transmission Delay and press TRANSMISSION DELAY Value: (0-600) (000): YES YES Arming Confirmation is the number of seconds of latched voltage (where voltage must stayed latched after) the panel will require before arming. This will be considered your exit delay. Enter the value you would like for the Arming Confirmation and press YES ARMING CONFIRMATION Value: (0-240) (0): YES 13 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS GPRS PARAMETERS ? Your APN code (Access Point Name) is given to you by your YES to enter into the parameter and use the Keypad to complete the code. Press YES to confirm your entry and the arrow to move to the next APN CODE Cellular Provider. Press parameter. Your USERNAME is given to you by your Cellular Provider. YES to enter into the parameter and use the Keypad to complete the name. Press YES to confirm your entry and the arrow to move to the next parameter. USERNAME Press Your PASSWORD is given to you by your Cellular Provider. PASSWORD YES to enter into the parameter and use the Keypad to complete the name. Press YES to confirm your entry and the arrow to move to the next parameter. Press YES YES APN CODE: xxxxx.xxxxxx.xxx YES USERNAME: xxxxxxxxxxx YES PASSWORD: xxxxxxxxxxxx Your IP1 address is given to you by your Central Station. IP1 ADDRESS YES to enter into the parameter and use the Keypad to complete the address. Press YES to confirm your entry and the arrow to move to the next parameter. YES Press *You will use either a IP address or a Domain Name but not both *When entering an IP address you must enter all 12 digits including preceeding 0s. IP1 ADDRESS: xxx.xxx.xxx.xxx DOMAIN NAME 1 Your Domain Name is given to you by your Central Station. YES to enter into the parameter and use the Keypad to complete the name. Press YES to confirm your entry and the arrow to move to the next parameter. DOMAIN NAME 1: xxxxx.xxx.xxx Press *You will use either a IP address or a Domain Name but not both leave it blank if an IP has already been entered. YES PORT 1 YES PORT 1: xxx The Port is given to you by your Central Station. By default the panel will use 888. If you need to modify the port press YES key to enter into the parameter and the keypad to complete the port. Press YES to confirm and the arrow to move to the next parameter. the ESC/NO Continue through IP2 and TMT IP. Once you have entered all valid parameters press ESC/NO to return to the main menu then ESC/NO again to move to the next parameter. GPRS PARAMETERS? ESC/NO 14 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS During the GPRS Level test the Modem will boot and attempt to gain access to the internet to post a Level out of 5 or an error Code that will help troubleshoot why it cannot connect. To keep the keypad awake use any keys on the keypad except the YES, ESC/NO, and CLR keys. This test can take up to 5 minutes. Once the level or error has posted press YES to continue in programming. GPRS LEVEL? YES TEST IN PROGRESS YES = END *For explanation of GPRS errors see bottom of page. GPRS LEVEL x/5 Videofied will require a 3/5 or better for reliable transmission of Video alarms RECORDING DEVICES Each device has a unique programming button. Please reference the Installation Sheet for the device you would like to program. PRESS PROGRAM BUTTON OF DEVICE YES *Note: If you are having issues pairing a device to the panel, please refer to the troubleshooting section. Press YES on Radio Range Test? You must allow the Radio Range test to run for at least 30 seconds (9/9) before stopping the test by pressing YES. (Device Type) # Recorded RADIO RANGE TEST? RF TEST x/9 Press ESC/NO if first Radio Range Test was successful. Use the arrow keys to select the proper area. Devices that need an entry/exit delay should be set to AREA 1. Devices that must be instant trigger should be AREA 2, 3, or 4. Press YES. RADIO RANGE TEST? AREA ALLOCATION: NAME LOCATION: FUNCTIONAL DEVICE TEST? ENTERING A NEW DEVICE? YES or ESC/NO CLOSE THE PANEL Before completing programming make sure that all tampers are depressed by verifying that each devices indicator LED is off. OPERATION COMPLETED? YES Other XT setup with CMA600 keypad (Standalone ONLY) Other setup (badges/codes, arming profiles, etc…) must be set with the CMA keypad GPRS error codes Codes 010 043 047 132 Error SIM card not detected/not inserted Provisioning problem, contact cellular provider Typographical error in APN Code, IP Address, or Port SIM card not activated 255 Cannot connect to cell tower 15 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Entering a Badge or Access Code for Arming/Disarming After Initial programming has been completed, you are not able to arm and disarm the system until you enter a user code or badge (the installer code cannot arm and disarm the system). Codes can th be 4-6 digits and the 4 digit must be 2 values higher or lower than any other code on the system: Example: User code 1234, next code cannot be 1235, 1236, 1233, or 1232 – These are reserved for Silent Duress and Audible Duress. The XT system can accept up to 19 Badges or Access codes in any combination. Press the arrow to move to BADGES ACCESS CODES. 10/12/27 10:53 DISARMED LVL:3 BADGES ACCESS CODES Enter the Installer code. YES BADGE OR CODE **** ENTER A BADGE/CODE Enter a 4-6 digit user code or present a badge to the reader for 2 seconds. BADGE OR CODE: **** YES Confirm the code by re-entering. YES CONFIRM THE CODE: Badge Presented YES Use the keypad to name the badge or code or leave it blank for the default name : ACCESS #. CODE NAME: NAME OF BADGE: YES ENTRY COMPLETE If you are entering any additional codes press YES. If you have completed entering Badges and Codes press and hold ESC/NO for 5 seconds to return to the main manu. YES ENTER A BADGE/CODE 16 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Changing Siren Options After initial programming has been completed any sounder on the system will be enabled by default, this includes the sounder on the Keypad and Badge Reader. While there is no way to disable the sounding of the exit delay you are able to disable the intrusion sound. Press the arrow to move to ACCESS LVL. 10/12/27 10:53 DISARMED LVL:3 ACCESS LEVEL Use your arrow keys to change the level to 4 YES ACCESS LVL: 4 YES Enter the installer code for the system Press the BADGE OR CODE **** CONFIGURATION to move to CONFIGURATION YES BADGE OR CODE Enter the installer code for the system GENERAL PARAMETERS Use the to move to ALARM MODES PROGRAMMABLE ALARM MODES PROGRAMMABLE YES Use the arrow keys to find the arming profile you would like to configure The letter underneath the area describes which devices will be armed when this profile is used. To change you must press the corresponding area number to cycle through the different letters. A= All Devices Armed D= All Devices Disarmed E= Only external devices armed P= Only perimeter device armed. Use the arrow keys to find the siren type you would like for the chosen profile. SIREN : All sounders are triggered during intrusion SILENT : No sounders are triggered during intrusion WITHOUT SIREN : Only arming device sounders are triggered during intrusion. DELAY BEEPS : Only delay beeps are sounded by the interior siren. FULLY ARMED SP1 SP2 AREAS: 1234 STATE: AAAA YES ALARM: WITHOUT SIREN YES 17 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS How to test to the dispatch center Testing to the dispatch is done twice during installation. Once while you are programming the system and then again once the installation has been completely finished. Although both will use the same steps the initial test will be just confirmation using one device to verify the programming. 10/12/27 10:53 DISARMED LVL:3 Enter a User code and press YES or present a badge to the reader. 10/12/27 10:53 **** YES The system will sound the exit delay through the keypad and badge reader. Once the delay has expired and the keypad says SYSTEM ARMED, put motion in front of a MotionViewer. If the MotionViewer is in area 1 you will need to wait for the entry delay to expire before disarming the system. Once the system has gone into alarm enter a User Code followed by YES or present a badge to the reader to disarm. ARMING THE SYSTEM SYSTEM ARMED SYSTEM ARMED **** The display will tell you that there has been an intrusion since the last time the system was armed. Press YES to continue. YES INTRUSION DETECTED YES After pressing YES the keypad will tell you which device has been triggered. Press YES to continue. (DEVICE NAME) (AREA) YES The system will go back to the main menu automatically but will not allow you to move around in programming until the system has disconnected from the central station. 10/12/27 10:53 DISARMED LVL:3 To verify that the system has transmitted you must contact the Dispatch Center and have the account information ready Note: Send 1 MotionViewer in at a time and verify with Central Station that they are getting Alarm and Video before tripping another MotionViewer. This will save time with the Central Station. 18 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS How to Disable Monitoring Disabling monitoring can be a useful tool in many situations. Before mounting devices and moving the panel to find a good GPRS level, disabling monitoring will ensure that you will have access to programming and that unnecessary signals are not sent to the monitoring station. When performing maintenance on the system disabling monitoring until the issue has been resolved will ensure that you will have access to programming throughout your troubleshooting. Press the arrow to move to ACCESS LVL. 10/12/27 10:53 DISARMED LVL:3 ACCESS LEVEL Use your arrow keys to change the level to 4 YES ACCESS LVL: 4 YES Enter the installer code for the system Press the BADGE OR CODE **** CONFIGURATION to move to CONFIGURATION YES BADGE OR CODE Enter the installer code for the system GENERAL PARAMETERS to move to CONFIGURATION MONITOR. Use the STATION CONFIGURATION MONITOR. STATION YES Press YES on MONITORING PARAMETERS MONITORING PARAMETERS Press YES on MONITORING ENABLED and use the to change the value to DISABLED and press YES to lock it in. Press and hold ESC/NO for 5 seconds to return to the main menu. MONITORING ENABLED YES MONITORING: DISABLED YES 19 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS How to test GPRS for deployment of panel Before the system is mounted you will need to check the GPRS level to make sure it is adequate. If the level is 3/5 or better you can mount the control panel in that location. Press the arrow to move to MAINTENANCE. 10/12/27 10:53 DISARMED LVL:3 YES Press the MAINTENANCE arrow to move to GPRS LEVEL. Press YES on GPRS LEVEL to start the test. GPRS LEVEL This test can take up to 5 minutes to complete. Pressing the YES, ESC/NO, or CLR buttons will prematurely end the test. This test will automatically issue the results to the display of the keypad when it has completed with either a level out of 5 (0/5-5/5) or an error code (listed below). Use the arrow keys to keep the keypad awake during the test. TEST IN PROG. YES = END GPRS LEVEL X/5 Press and hold ESC/NO for 5 seconds to return to the main menu. GPRS LEVEL YES GPRS Errors when running GPRS LEVEL Codes Error 010 043 132 255 SIM card not detected/not inserted Provisioning problem, contact cellular provider SIM card not activated Cannot connect to cell tower GPRS Codes in Event Log Codes Error 256 Cannot connect to cell tower 11 SIM not ready if multiples, SIM not detect if only one 48 Signal rejected by host, IP, Domain Name, or Port are incorrect 20 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS How to test RF for deployment of devices Running the RF test during the mounting of devices is key to a successful Videofied installation. This test will ensure that all devices have adequate communication with the control panel. All Videofied devices are bi-directional which allows the system to ping the device and expect a response. The number of successful responses out of 9 will be displayed on the keypad for the device you are running the test for. This is also a relative range that will change in real time as you walk further away from the control panel and back closer. Press the arrow to move to MAINTENANCE 10/12/27 10:53 DISARMED LVL:3 YES Press the arrow to move to DEVICE LOCATING Press YES on DEVICE LOCATING to get to the list of devices. Use the arrow keys to find the device you would like to run the test for. MAINTENANCE DEVICE LOCATING YES (DEVICE NAME) This test will run as long as you need it to. Pressing the YES, ESC/NO, or CLR buttons will end the test. This test will show the results on the display of the keypad relative to the number of successful pings to the panel. It is required to run the test for at least 30 seconds at the mounting location for accurate results and to have a 9/9 for reliable transmission of alarms and video. Press YES when you are finished with the test. Press and hold ESC/NO for 5 seconds to return to the main menu. RF TEST 0/9 YES YES (DEVICE NAME) Once all devices are checking in at 9/9, you are ready to test the full system to your central station. After arming and tripping each device call the central station and verify alarm and video of each device with dispatch. Now you are ready to show the customer how to use the system. NOTE: To insure proper operation of the system you must get 9/9 with each device before mounting. 21 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS GPRS Antenna Connection ! WARNING ! Use caution before removing antenna connection. Damaged antenna connector is NOT covered under warranty. Using needle nose pliers, be sure to only grab the connector and pull directly up Arming Input Wiring Diagram HOST When in Arm From Host mode the Videofied system will only arm and disarm when 9-12v is supplied and sustained. Arming Input 1 will arm/disarm Areas 1 & 2 Arming Input 2 will arm/disarm Areas 3 & 4 22 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS General Programmable Input Configuration 23 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 24 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 25 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 26 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 27 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 28 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 29 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 30 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 31 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS How to enable the External RF Antenna The XTO 600/610 control panels have built in High Gain RF and GPRS antennas. The GPRS external comes pre-activated and hooked up, while the RF antenna is hooked up but needs to be activated in Configuration after you have completed initial programming. The following steps will walk you through how to enable the High Gain RF antenna after initial programming. Press the arrow to move to ACCESS LEVEL #. 10/12/27 10:53 DISARMED LVL:3 ACCESS LEVEL Press YES and use the to move the level to 4 YES ACCESS LVL: YES BADGE OR CODE: **** Enter the Installer code. Press the CONFIGURATION arrow to move to CONFIGURATION Enter the Installer Code YES BADGE OR CODE: **** GENERAL PARAMETERS YES SITE IDENTIFICATION Left or Right arrow until you see RADIO OPTIONS and press YES. Use the arrow keys to change it to External and press YES. RADIO OPTIONS: EXTERNAL YES 32 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS How to mount the XT600i/610 and XTX600/610 How to Mount the Control Panel? Fix the back casing on the wall with 3 screws () How to Mount the XTO600/610 Included Mounting Hardware: Case and Mounting Screws, locking washers, bolts and nuts. Mounting Brackets 1. Install the Weather Resistant Wire Port. 33 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 2. Place the cover on the base. 1. When closing the cover be sure to line up the two BOTTOM stickers face to face. 2. Be Careful not to slide the cover on. Instead come straight down in order to have the cover tamper properly seat. 3. Screw the cover to the base using the provided 8 screws. NOTE: To ensure proper functioning and to keep the case water proof you must mount the panel with the wire channel facing down. 4. Place the L shaped mounting bracket onto the base using the provided bolts. 5. Place the two U shaped brackets around the pole and attach the locking bracket. Use the locking washers and nuts to attach the U bracket to the L mount. 34 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Troubleshooting Monitoring Station is not getting ANY video but is getting signals: Good communication between the MotionViewers and the Control Panel is key to getting successful video to the monitoring station. During mounting of any device on your Videofied system you must run the Radio Range/Device Locating test to ensure that the mounting location is with-in range of the Control Panel. Concrete, Metal and earth are some of the largest RF inhibitors and should be taken into account when choosing mounting locations. When running the Radio Range/Device Locating test you should have the site as close to the same as it would be when the site is closed/no one is there, i.e. close garage doors/service doors, etc. Device locating steps can be found on Page 17. Devices are not sending Video clips YES – There are faulty devices Check Maintenance/ Display Faulty Devices NO – There are no faulty devices MotionViewers come up with ‘Radio Problem’. This means that the MotionViewers are currently not talking with the Control Panel. Run Maintenance/ Device Locating Device Locating will test the RF signal strength between the device and the Control Panel. For reliable transmission this result must be a 9/ 9. This is the number of successful pings between the device and the Control Panel so a loss of just 1 packet could cause failure to transmit video. Bring the devices back to the Control Panel and hit the programming button to force them to sync back with the panel. Important Note: Videofied will only automatically download the first MotionViewer video that is taken and only if this is the primary event or reason for the panel connecting with the monitoring station. If the account is on test you will only ever get the first video downloaded. If you are only getting the events at the station and all tests above pass more than likely you are sending a preceding event (like an arming signal or door contact) which will cause the video to not auto download because the video is not the primary event. 35 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Monitoring Station is not getting any signals: Communication between the Control Panel and the Monitoring Station is over the GPRS side of the GSM cellular network. You will want to check your GPRS level to see if there is an error/level is too low. You must have a 3/5 or better for reliable transmission to the Monitoring Station. How to run the GPRS level test and GPRS error codes can be found on page 16. If you receive a successful GPRS level test you will want to check the panel event log for more GPRS errors that could be occurring during the attempted transmission but after cellular authentication. No Signals are received at the Monitoring Station GPRS Error Run GPRS Level test in Maintenance GPRS Level 3/5-5/5 GPRS LEVEL RECEIVED GPRS Level 0/5-2/5 GPRS errors can be found on Page 16 of the manual. Check the panel event log. This will give additional GPRS errors that may be occurring during the attempt of transmission. See Page 16 for Event Log GPRS meanings. Your signal strength must be 3/5 or better for reliable transmission to the monitoring station. There are external antennas available and other cellular repeater options if needed to boost cellular reception Panel is staying CONNECTED WITH MONITOR STATION While the Control Panel is attempting or is connected with the Monitoring Station you will see this message when you attempt to move around on the keypad. If the system is not successful in connecting with the station it will retry the connection multiple times, locking you out of programming until it is done trying. This normally can take anywhere between 15-20 minutes. If you want to force the panel to disconnect you must o 1. Remove the batteries from the control panel o 2. Secure the cover tamper of the panel o 3. Re-insert the batteries into the control panel and sync the keypad back by pressing the CLR and ESC/NO buttons at the same time. o 4. Access the Configuration menu by changing you access level to 4 and go to Configuration Monitor Station. o 5. In Monitoring Parameters – Disable monitoring until the connection issue is resolved. 36 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Unable to record device or getting ‘Pairing Failure’ error This usually occurs when the device still has a pairing key from a previous system or setup. To perform a pairing key override: 1. Remove all batteries from the device. 2. Make sure your system is ready to record devices: o A. If learning in the keypad, press the panel’s programming button. DO NOT HOLD THE PANEL’S PROGRAMMING BUTTON o B. If learning in additional devices, make sure the keypad reads ‘Press Programming Button Of Device’ 3. Insert a single battery into the device. 4. Wait 1 second for device to power up. 5. Press programming button of device (for keypads press ‘CLR’ & ‘ESC/NO’ keys at the same time) For the 4-button remote keyfobs the process is slightly different: o 1. Press and hold the ‘ON’ and ‘OFF’ keys at the same time for 12 seconds o 2. Wait 1 second o 3. Press and hold the ‘ON’ and ‘OFF’ keys at the same time for 5 seconds, you should hear 4 beeps from the keyfob. XT -SERIES ‘AFTER INITIAL PROGRAMMING’ FLOW CHART 37 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS PROGRAMMABLE INPUTS CONFIGURATION Page 36 GENERAL PARAMETERS Page 37 Page 37 ALARM MODES PROGRAMMABLE RESPONDING PARTY LIST Page 38 AREAS AND DEVICES Page 39 CONFIGURATION MONITOR. STATION SITE IDENTIFICATION FULLY ARMED VIDEOMAIL ALARM ADDRESS DEVICES MONITORING PARAMETERS XTENDER ALARM MODE SP1 EMAIL SENDER AREAS PERIODIC TEST PROGRAMMABLE OUTPUTS ALARM MODE SP2 Not Supported in the North American Market SIREN DURATION INTRUSION 90sec ALARM CODES PROGRAMMABLE INPUTS SIREN DURATION TAMPER 90sec GPRS PARAMETERS ENTRY DELAY 15sec RADIO OPTION EXTERNAL ANTENNA EXIT DELAY 45sec DELAY BEEPS ENABLED AUTO ARMING DELAY DISABLED SCHEDULING WARNING BIP ENABLED 38 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS GENERAL PARAMETERS GENERAL PARAMETERS SITE IDENTIFICATION GPRS PARAMETERS PANEL PHONE NUMBER APN CODE NAME OR ADDRESS USERNAME XTENDER PASSWORD ARMING OPTION STANDALONE IP ADDRESS 1 0.0.0.0 ENTRY DELAY 000 DOMAIN NAME 1 TRANSMISSION DELAY 000 PORT 1 888 ARMING CONFIRMATION IP ADDRESS 2 0.0.0.0 ARMING MODE SLOW DOMAIN NAME 2 PROGRAMMABLE OUTPUTS PORT 2 888 PROGRAMMABLE OUTPUT 1 TMT IP ADDRESS 0.0.0.0 STATUS DISABLED LENGTH ACTIV. 180 sec DOMAIN TMT EVENT TYPE INTRUSION PORT TMT 888 OUTPUT NAME PAQUET SIZE 512 PROGRAMMABLE OUTPUT 2 DATA TIMEOUT 20 PROGRAMMABLE INPUTS SMTP GPRS PROGRAMMABLE INPUT 1 PORT GPRS 3389 TRANSMISSION DISABLED MAX TCP PACKET ALARM MODE ALARM RINGTONE OFF INPUT TYPE NORMALLY OPEN EVENT TYPE INTRUSION RADIO OPTIONS INTERNAL ANTENNA INPUT NAME SIREN MODE MAPPING DISABLED PROGRAMMABLE INPUT 2 PROGRAMMABLE INPUT 3 39 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS ALARM MODES PROGRAMMABLE / RESPONDING PARTY LIST ALARM MODES PROGRAMMABLE RESPONDING PARTY LIST VIDEOMAIL ALARM ADDRESS FULLY ARMED AREAS:1234 STATE: AAAA SELECT/MODIFY EMAIL ADDRESS ALARM: SIREN ENTER NEW EMAIL ADDRESS EMAIL SENDER ALARM MODE SP1 Not supported in the North American Market AREAS: 1234 STATE: AAAA ALARM: SIREN DESIGNATION MODE ALARM MODE SP2 AREAS: 1234 STATE: AAAA ALARM: SIREN DESIGNATION MODE 40 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS AREAS AND DEVICES AREAS AND DEVICES EXIT DELAY 45sec DEVICES ADD A NEW DEVICE DELAY BEEPS ENABLED DEVICE CONFIGURATION AUTO ARMING DELAY DISABLED LIST OF DEVICES SCEDULING DELETE DEVICE SCHEDULING OFF CHANGING NAME DEVICE CALENDAR MANAGEMENT CHANGING AREA DEVICE WARNING BIP DISABLED 24 HOUR DEVICE DISABLED AREAS LIST OF AREAS 24H SIREN MODE AREA CONTENT LIST OF DEVICES IN AREA CHANGING NAME AREA SIREN DURATION INTRUSION 90sec SIREN DURATION TAMPER 90sec ENTRY DELAY 15sec 41 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS CONFIGURATION MONITOR. STATION CONFIGURATION MONITOR. STATION MONITORING PARAMETERS MONITORING ENABLED ACCOUNT NUMBER PERIODIC TEST PERIODIC TEST 24 HOURS TEST HOUR 15:00 SYSTEM ARMED DISABLED ALARM CODES TRANS. STATE MODIFICATION LIST OF TRANSMITTED EVENTS PPP CONNECTION DOMAIN NAME PPP USER NAME PPP PASSWORD 42 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS Addendum 1. LSH20 Control Panel Batteries: 2. LS14500 Peripheral Batteries: Excludes SE601 and SE651 3. Lithium Battery Storage: 43 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110 2011/11/10 Ed 1.5 Setup and Programming manual for XT series GPRS 4. Finding Manufacture Week and Year: The Manufacture week and year can be found in the serial number of the device/control panel. The second sets of 4 numbers in the serial number are WWYY. ####0411######## = Which shows that this device was manufactured in the 4th week of 2011. 44 | P a g e 4455 White Bear Parkway, Suite 700 White Bear Lake, MN 55110
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 44 Language : en-US Tagged PDF : Yes Author : Andrew Opp Creator : Microsoft® Office Word 2007 Create Date : 2012:04:02 11:13:13 Modify Date : 2012:04:02 11:13:13 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools