RX Infotech P LWP-01 Wireless Presenter with Red Laser Pointer User Manual

RX Infotech P Ltd Wireless Presenter with Red Laser Pointer

User Manual

- 1 -                 Be sure to carefully read this user’s manual before using the wireless presenter and keep it for future reference.    Wireless Presenter With Red Laser Pointer
- 2 - WARNING! RISK OF INJURY! Laser  beams can  cause permanent  damage  to the eyes. Do not look into the laser beam or shine the  laser  beam  into  your  eyes,  other  peoples’ eyes,  or  the  eyes  of  pets.  Be  careful  when pointing it towards reflective surfaces.    Keep  this device away from Children. This is a working tool, not a toy. It should only be used by adults.  Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means,  electronical  or  mechanical,  for  any purpose, without prior permission of the seller.    The  seller  provides  this  document  without warranty, or condition of any kind. The seller may make  improvements  or  changes  in  the  product described in this document at any time.
- 3 - Chapter 1  Introduction I.  Product description Featuring  a  pen-like  design,  alt-tabbing  and hyperlink  functions  in  presentations,  it  is  an intuitive  and  easy  to  use  tool  for  any  and  all presentations. Thanks to the built in laser pointer you can point out details to your audience while you  present  from up  to  100  meters  range.  The USB  connector  is  securely  placed  within  the presenter  itself,  making  sure  you  are  always ready. II.  Features 1)  PowerPoint, Keynote and Prezi support The  functions  of  page  down  and  page  up buttons  can  be  switched  between  Page Down/Up,  Left/Right  Arrow  and  Up/Down Arrow, by pressing the page down and page up buttons at the same time. 2)  2.4G  RF  frequency,  which  is  an  ISM  free frequency and can be used world-wide. Up to 100  meters’  wireless  range,  By  using frequency hopping technology to improve the signal to noise ratio. It is Omni-directional and as such allows  for the control  of devices in other rooms. 3)  Through  UniCoding  6  technology,  the
- 4 - transmitter  can  control  1  up  to  6  USB receivers. 4)  Support  functions  including  Page  up  and Page down,Full screen, Black screen. 5)  Support hyperlinks function in PowerPoint. 6)  Soft Silica Gel buttons allow for comfortable use.   7)  Storable receiver for easy carrying. The USB receiver  can  be  stored  inside  the  wireless presenter. 8)  Safe laser class complies with EN60825-1. 9)  Easy control of volume up/down. 10)  Compatible with USB3.0, plug and play. 11)  Three  ways  to  save  power  consuming  by auto  standby,  deep  sleeping  and  power switch. 12)  360mAh  Polymer  Lithium  battery  and  low power reminding function. The led will flash slowly when the power is low. III.  Operation system Windows  7/8/10  and  above,  Mac  OS,  Linux, Android 4.3 or above. IV.  Package contents 1)  Wireless presenter *1 2)  User Manual*1 3)  Charge Cable*1
- 5 - Specifications Transmitter Technology:      Radio Frequency Frequency:      2.4GHz Control Distance:    >100m Laser      Class 2M Max Output:    <1mW Laser Distance:     >200m Wavelength:    650nm/532nm Battery:     360mAh Polymer Lithium   Battery Working Voltage:  3.7V Sleep Current    <10uA Dimension:         138*18*13mm Weight:     32.1g USB Receiver Working Voltage:  5V DC Dimension:         24.7*13.8*5.14 mm Weight:     1.9g
- 6 - Chapter 2  Getting Started V.  Function map
- 7 - VI.  Function Description 1)  Press and hold “Laser Pointer” button to turn on the laser, release button to turn it off. 2)  Use  the  Microsoft  PowerPoint  to  open PowerPoint files. 3) Press “Page Up” button for 2 seconds to Start a slideshow from the current slide. Press the button for 2 seconds again to escape from the full screen. 4) Press  “Page  Down”  button  and  “Page  Up” button to go forward and backward. 5)  Press“Page Down” button for 2 seconds to enter into black screen. Press “Page Down” button for 2 seconds again to escape. Note: When you  press “Page Down” button for 2 seconds to enter the black screen, the USB receiver will send the letter ‘b’ or comma ‘,’  to  the  PowerPoint.  If  the  Input  Method Editor is open, the letter ‘b’ or comma‘,’ will be intercepted  and  cannot  be  sent  to  the PowerPoint.  In  this  case,  try  to  turn  off  the IME or switch to the English input mode. 6)  If hyperlinks exist on the page, click           button, you can jump among the hyperlinks and double click      can be used to open the hyperlink.  To  click        is  same  as  to  press
- 8 - Tab on keyboard. To double click        is same as  to  press  Enter  on  keyboard.  For  WPS doesn’t support jumping hyperlinks by Tab, so WPS doesn’t support this function. 7)  After the hyperlink is opened, you can press and  hold      button  to  switch  between  all opened  application  windows.  Release  it  to turn to the window you want to switch to. To press and hold   button is same as to press Alt-Tab on keyboard. 8)  The presenter supports PowerPoint, Keynote and  Prezi by  switching  the  functions of  the page down/up buttons. By default, the page down/up buttons of the presenter function as the Up/Down Arrow on keyboard, which can support  PowerPoint  and  Keynote.  By pressing  the  page  down/up  buttons  at  the same time, the function will change to the left and  right  arrows  on  the  keyboard  for  Prezi support. Doing it a second time changes the function  to  page  up  and  down,  which supports  many  other  programs.  Pressing them together a third time will revert back to the default setting. 9) Press “volume up”  or “volume down” on the side, you can adjust system volume.
- 9 - VII. Installation 1)  Take out the mini USB receiver 2)  Plug the USB receiver into USB port.       3)  Operate the wireless presenter 4)  Turn off the wireless presenter
- 10 - VIII. Charging the wireless presenter 1)  Low power indication When  the  power  is  low,  the  red  LED  will  flash slowly to remind the user to recharge the wireless presenter. 2)  Recharging the wireless presenter Connect the wireless presenter to a USB port, the red LED will stop flashing and keep red to show the wireless presenter is being recharged.   If the red LED turns off, it means the recharge is completed. Normally the recharging time is about two hours.
- 11 - Chapter 3  Frequently Asked Questions 1. How to know the battery is out of power? Turn on the power switch of the presenter, then press  laser  button to  check  if  the  laser  can be turned on. If the laser cannot be turned on, usually it means the battery is out of power or the laser diode is broken and need replacement. In other case, if the LED on the wireless presenter starts to flash slowly, it means the power is low and the battery needs to be recharged.   2. why does the laser pointer not work? First,  check  the  power  switch.  Second,  check whether the wireless presenter is in low power or out of power. If the LED flashes slowly, it means the  power  is  low  and  the  battery  needs  to  be recharged. If all the other buttons can work, only the laser pointer cannot work, the laser diode may need  replacement.  Third,  check  the  place  of anode  and  cathode  of  battery.  Before  putting  a battery into the  presenter, remember  to remove the plastic cover of the battery. 3. When the  mini USB receiver plugs  into the PC  USB,  the  computer  does  not  detect  the device, why? Please check whether the USB works or not. You
- 12 - can  use  a  USB  mouse  or  keyboard to  test  the USB port. If a USB mouse or keyboard works on the  USB  port  and  the  USB  receiver  of  the presenter doesn’t, it means the USB receiver of the presenter is broken or the USB drivers is not compatible with the USB receiver.  You  can  try  another  USB  port  of  the  same computer  or  USB ports  of  another  computer  to check whether the USB receiver of the presenter is working. If it works on other computer, it means the  USB  drivers  of  the  computer  are  not compatible  with  the  USB receiver. You  need  to back up your data and reinstall the OS. 4. The laser is ok and the USB receiver can be detected  by  the  computer,  but  the  presenter cannot control the computer, why? The reason is the USB receiver doesn’t save the presenter’s  address  properly.  You  can  use  a CodeMatch  software  to  let  the  USB  receiver to save the presenter’s address again.  IX.  Certifications CE, ROHS, FDA, FCC ID
ÚÝÝ É¿®²·²¹æ̸· »¯«·°³»²¬ ¸¿ ¾»»² ¬»¬»¼ ¿²¼ º±«²¼ ¬± ½±³°´§ ©·¬¸ ¬¸» ´·³·¬ º±® ¿ Ý´¿ Þ ¼·¹·¬¿´ ¼»ª·½»ô °«®«¿²¬ ¬± °¿®¬ ïë ±º ¬¸» ÚÝÝ Î«´»ò ̸»» ´·³·¬ ¿®» ¼»·¹²»¼ ¬± °®±ª·¼» ®»¿±²¿¾´» °®±¬»½¬·±² ¿¹¿·²¬ ¸¿®³º«´ ·²¬»®º»®»²½» ·² ¿ ®»·¼»²¬·¿´ ·²¬¿´´¿¬·±²ò ̸· »¯«·°³»²¬ ¹»²»®¿¬»ô «» ¿²¼ ½¿² ®¿¼·¿¬» ®¿¼·± º®»¯«»²½§ »²»®¹§ ¿²¼ô ·º ²±¬ ·²¬¿´´»¼ ¿²¼ «»¼ ·² ¿½½±®¼¿²½» ©·¬¸ ¬¸» ·²¬®«½¬·±²ô ³¿§ ½¿«» ¸¿®³º«´ ·²¬»®º»®»²½» ¬± ®¿¼·± ½±³³«²·½¿¬·±²ò ر©»ª»®ô ¬¸»®» · ²± ¹«¿®¿²¬»» ¬¸¿¬ ·²¬»®º»®»²½» ©·´´ ²±¬ ±½½«® ·² ¿ °¿®¬·½«´¿® ·²¬¿´´¿¬·±²ò ׺ ¬¸· »¯«·°³»²¬ ¼±» ½¿«» ¸¿®³º«´ ·²¬»®º»®»²½» ¬± ®¿¼·± ±® ¬»´»ª··±² ®»½»°¬·±²ô ©¸·½¸ ½¿² ¾» ¼»¬»®³·²»¼ ¾§ ¬«®²·²¹ ¬¸» »¯«·°³»²¬ ±ºº ¿²¼ ±²ô ¬¸» «»® · »²½±«®¿¹»¼ ¬± ¬®§ ¬± ½±®®»½¬ ¬¸» ·²¬»®º»®»²½» ¾§ ±²» ±® ³±®» ±º ¬¸» º±´´±©·²¹ ³»¿«®»æ± Î»±®·»²¬ ±® ®»´±½¿¬» ¬¸» ®»½»·ª·²¹ ¿²¬»²²¿ò± ײ½®»¿» ¬¸» »°¿®¿¬·±² ¾»¬©»»² ¬¸» »¯«·°³»²¬ ¿²¼ ®»½»·ª»®ò± ݱ²²»½¬ ¬¸» »¯«·°³»²¬ ·²¬± ¿² ±«¬´»¬ ±² ¿ ½·®½«·¬ ¼·ºº»®»²¬ º®±³ ¬¸¿¬ ¬± ©¸·½¸ ¬¸» ®»½»·ª»® · ½±²²»½¬»¼ò± ݱ²«´¬ ¬¸» ¼»¿´»® ±® ¿² »¨°»®·»²½»¼ ®¿¼·±ñÌÊ ¬»½¸²·½·¿² º±® ¸»´°òÝ¿«¬·±²æ ß²§ ½¸¿²¹» ±® ³±¼·º·½¿¬·±² ¬± ¬¸· ¼»ª·½» ²±¬ »¨°´·½·¬´§ ¿°°®±ª»¼ ¾§ ³¿²«º¿½¬«®»® ½±«´¼ ª±·¼ §±«® ¿«¬¸±®·¬§ ¬± ±°»®¿¬» ¬¸· »¯«·°³»²¬ò̸· ¼»ª·½» ½±³°´·» ©·¬¸ °¿®¬ ïë ±º ¬¸» ÚÝÝ Î«´»ò Ñ°»®¿¬·±² · «¾¶»½¬ ¬± ¬¸» º±´´±©·²¹ ¬©± ½±²¼·¬·±²æ øï÷ ̸· ¼»ª·½» ³¿§ ²±¬ ½¿«» ¸¿®³º«´ ·²¬»®º»®»²½»ô ¿²¼ øî÷ ¬¸· ¼»ª·½» ³«¬ ¿½½»°¬ ¿²§ ·²¬»®º»®»²½» ®»½»·ª»¼ô ·²½´«¼·²¹ ·²¬»®º»®»²½» ¬¸¿¬ ³¿§ ½¿«» «²¼»·®»¼ ±°»®¿¬·±²ò

Navigation menu