Radiance Instruments TMW017G SMOKE GATEWAY User Manual TMW017G Manual r2

Radiance Instruments Ltd. SMOKE GATEWAY TMW017G Manual r2

Contents

TMW017G_Manual_r2

Smoke Gateway connects your Smoke Professional BBQ Thermometer
to the Smoke Gateway mobile app on your smartphone or tablet. Smoke
Gateway pairs to your Smoke base unit, and then connects to your Wi-Fi.
Only one Smoke base unit can connect at a time to a Smoke Gateway.
What’s Included:
Smoke Gateway, lithium rechargeable battery (installed), power adapter, USB
charging cable, and this instruction guide.
Set Up:
1. Download the Smoke Gateway mobile app from Apple App Store
or Google Play.
2. Follow the on-screen instructions in the app to pair your Smoke
Gateway to your Smoke base unit (via Radio Frequency [RF]
wireless), and then connect it to your local Wi-Fi.
To Operate:
Press the power button to turn Smoke Gateway on (double blue flash).
Press and hold the power button for 3 seconds to power Smoke Gateway off
(double red flash).
Smoke Gateway can run for up to 100 hours on battery power. Alternatively,
Smoke Gateway will also run connected to mains power.
(Smoke Gateway ships with partial charge; it is recommended to charge before
use)
To Charge:
When the battery is low, the LED will flash red twice every 2 seconds then turn
off after 1 minute. Connect Smoke Gateway to mains power using the included
power adapter and USB charging cable. When the unit is fully charged the LED
will change from solid red to solid blue. Allow approximately 8 hours to fully
charge. You can check the battery level of Smoke Gateway by going to ‘Settings’
on a single channel.
Transmission Distance:
Smoke Gateway should be located within 300-feet (line of sight) of the Smoke
base unit for best results, and within range of your Wi-Fi network.
Hard Reset:
To perform a hard reset on Smoke Gateway, press the RESET button on the back
of the device. Your connection settings will not be lost.
Firmware Updates:
Smoke Gateway will update itself automatically with the latest firmware
when connected to Wi-Fi.
Smoke Gateway
Operating Instructions
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Industry Canada Licence-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
d’en compromettre le fonctionnement.
Special Notice
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2AI67-TMW017G / IC: 22116-TMW017G
P-15-012-02-b
www.thermoworks.com
741 E. Utah Valley Dr.
American Fork, UT 84003
For service or warranty:
1-800-393-6434
1-801-756-7705
techsupport@thermoworks.com
applicables aux appareils radio exempts de licence. L’exploitation est
Le présent appareil est conforme aux CNR d’Industrie Canada
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
brouillage radioélectrique subi, même si le brouillage est susceptible
This equipment complies with the FCC RF radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters between
the radiator and your body.
Smoke
VOL
SET
SET
ON
OFF
ON
OFF
2
1
°C/°F CAL
ON
OFF
Smoke Receiver
PROBE 1
PROBE 2
Smoke Gateway
RESET
(Wi-Fi ID: Gateway_xxxxxx)
Operating Instructions
1. Single press to turn on.
(Double blue flash)
2. Hold for 3 sec. to turn off.
(Double red flash)
3. LED flashes every 5 sec.
BLUE - functioning normal
RED - resync to Smoke base
PURPLE - Wi-Fi comm. lost
4. Flashes red twice every 2 seconds
for 1 min. – Charge battery.
5. Follow app instructions for setup.
6. Splashproof, do not submerge.
Smoke
VOL
SET
SET
ON
OFF
ON
OFF
2
1
°C/°F CAL
ON
OFF
Smoke Receiver
PROBE 1
PROBE 2
Smoke Gateway
RESET
(Wi-Fi ID: Gateway_xxxxxx)
Operating Instructions
1. Single press to turn on.
(Double blue flash)
2. Hold for 3 sec. to turn off.
(Double red flash)
3. LED flashes every 5 sec.
BLUE - functioning normal
RED
- resync to Smoke base
PURPLE - Wi-Fi comm. lost
4. Flashes red twice every 2 seconds
for 1 min. – Charge battery.
5. Follow app instructions for setup.
6. Splashproof, do not submerge.
Smoke
VOL
SET
SET
ON
OFF
ON
OFF
2
1
°C/°F CAL
ON
OFF
Smoke Receiver
PROBE 1
PROBE 2
Smoke Gateway
RESET
(Wi-Fi ID: Gateway_xxxxxx)
Operating Instructions
1. Single press to turn on.
(Double blue flash)
2. Hold for 3 sec. to turn off.
(Double red flash)
3. LED flashes every 5 sec.
BLUE - functioning normal
RED - resync to Smoke base
PURPLE - Wi-Fi comm. lost
4. Flashes red twice every 2 seconds
for 1 min. – Charge battery.
5. Follow app instructions for setup.
6. Splashproof, do not submerge.
(Back) (End)
On/Off
Hard reset
USB connection
LED Light:
When the unit is turned on and operating normally the LED will flash every
5 seconds. When flashing BLUE, everything is working properly. If flashing
RED every 5 seconds, the connection to your Smoke base unit (RF) is not
working properly. If flashing purple, Wi-Fi is not connected properly. During
setup the LED light will flash per the app instructions.
Care & Maintenance:
Power Smoke Gateway off when not in use to conserve battery power.
Store at room temperature in dry location.
LED Light

Navigation menu