Radio Shack 1501995 User Manual REVISED Users Manual with FCC Statement

RadioShack Corporation REVISED Users Manual with FCC Statement

Contents

REVISED Users Manual with FCC Statement

Download: Radio Shack 1501995 User Manual REVISED Users Manual with FCC Statement
Mirror Download [FCC.gov]Radio Shack 1501995 User Manual REVISED Users Manual with FCC Statement
Document ID51367
Application IDWFT4TbBLtdhb6TIxGAVh1Q==
Document DescriptionREVISED Users Manual with FCC Statement
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize140.04kB (1750536 bits)
Date Submitted1999-08-02 00:00:00
Date Available1999-08-04 00:00:00
Creation Date1999-07-01 19:24:00
Producing SoftwarePhotoshop PDF Plug-in 1.0
Document Lastmod1999-08-02 09:18:06
Document TitleREVISED Users Manual with FCC Statement
Document CreatorPhotoshop PDF Plug-in 1.0

Cat. No. 15-1995
OWNER’S MANUAL
7-in-0ne Home Theater Remote Control
Please read before using this equipment
I TRODUCTION
Your Radio Shack 7—in-One lR/RF Remote Control can replace up to seven infrared
remote controls. You can use it to control your TV, VCR, cable converter, satellite
receiver, CD player, tuner, phonograph, video accessory, digital audio tape, cassette,
laser disc player, or DVD player,
Unlike some universal remote controls, this remote control is preprogrammed with the
most commonly used commands and does not have to learn its commands from the
original remote controls, All you have to do is tell it which device‘s remote controls you
want to replace (by entering 4-digit codes).
This manual includes a list ofmany manufacturers“ 4-digit codes for your devices After
you enter the codes for your original remotes, the 7-in-One lR/RF Remote is ready to
operate the original remotes’ most used functions.
The 7-in-One transmits both infrared (IR) and radio frequency (RF) signals, so you don’t
need to be within “line—of~sight” to control devices. With the supplied IR/RF Command
Center, you can use the remote to control device in any room of your home.
CONTENTS
Preparation............
lnstalling Battenes.
Setting the Clock...
A Look at Your Remote
Setting Up the Remote....
T0 Operate Your TV,
T0 Operate Your VCR ...................
To Operate Your TV/VCR Combination
To Operate Your Cable Convener.
To Operate Your Satellite Receive
To Operate Your CD Player ........
To Operate Your Receiver/Tuner.
To Operate Your Amplifier.
To Operate Other Devices”
Special Features....... .......
Searching for a Code.
Using the Sleep Function.
Favorite Channel Scan ......................
Clearing Favorite Channel Scan
Converting Device Keys
Volume Punch-Through
Using the Macro Keys..
Setting Up Timed Sequences .......
Setting Up the Home Theater Key
Clear All ..............................
Using the IR/RF Command Center
Troubleshooting... ................
PREPARATION
INSTALLING BATTERIES
Your Radio Shack 7-in-One requires four AAA batteries (not supplied), available at your
local Radio Shack store,
Cautions:
0 Use only fresh batteries of the required size and recommended type.
0 Do not mix old and new batteries, different types of batteries (standard.
alkaline, or rechargeable), or rechargeable batteries of different capacities,
To install the batteries:
1. Press the battery compartment cover’s tab and lifi off the cover
2. Place the batteries in the compartment as indicated by the polarity symbols
(+ and -)marked inside.
3. Replace the cover
[f the batteries are installed correctly and the red indicator does not light when you press
POWER, replace the batteries.
Note: Removing the batteries will not require you to reprogram your remote control
because the 7-in-One lR/RF Remote Control has unlimited memory backup.
Cautions:
- Dispose of old batteries promptly and properly, Do not bum or bury them.
0 Always remove old or weak batteries. Batteries can leak chemicals that can
destroy electronic parts.
N otes:
- After you install batteries, the remote performs a test of the display for 10 seconds or
until you press a key.
0 To extend battery life, the display turns off after 10 seconds of keypad inactivity and
turns on again when you press any key.
0 Device codes you have progammed into the 7-in-One remain stored in memory
while you replace the batteries. However, you must reset the clock.
SETTING THE CLOCK
Follow these steps to set the clock on the 7-in-One’s display.
1.
2.
3.
4.
Hold down P until TIMED SEQ. Appears.
Press J, twice. CONFIGURE appears.
Press SELECT. THEATR SEL appears.
Press if again. TIME SETUP appears.
Press SELECT. TIME appears and the first digit in the time flashes. Enter the time
in 12-hour format. AM/PM flashes.
If necessary, press iv to toggle between AM and PM, then press SELECT. The day
of the week display appears.
Use T and i to toggle through the days of the week until the current day appears, then
press SELECT. The currently selected device and the correct time appear.
QUICK SETUP
The steps in this section tell you how to quickly set up the 7-in-One to operate all of your
devices.
To set up devices individually, or add a device after you have set up the 7-in-One, see the
appropriate section under “Setting Up the Remote“.
Note: For the best operation, you should be within 15 feet ofthe device you want to
control.
Follow these steps for quick setup:
1.
2.
Turn on all of the devices you are setting up.
Press TV.
Hold down P until TIMED SEQ appears.
Press in CODE SETUP appears,
Press SELECT. DEV SET UP appears
Press SELECT again. TV appears.
10.
II.
12.
Enter the fist four-digit TV code listed for your TV’s brand in “Setup Codes for
TV’s" on page 7 7, then press SELECT.
Note: lfthe 4-digit code begins with zero, only the last 3-digits will appear on the
display.
Point the remote at your TV and press POWER. Your TV should turn off. lfit does
not, enter the next code from the list and press SELECT then POWER again. When
your TV tums off, press VCRA VCR appears
Enter the first four~digit VCR code listed for your VCR’s brand in “Setup Codes for
VCR’s" on page 7 _ or “Setup Codes for TV/VCR Combinations" on page _ _, then
press SELECT,
Point the remote at your VCR and press POWERA Your VCR should turn off. lfit
does not, enter the next code from the list and press SELCT then POWER again.
When your VCR turns off, press CBL. CABLE appears.
Continue setting up devices by pressing the appropriate device key, entering your
device‘s code and pressing SELECT, Refer to the code list for the type ofdevice
you want to set up:
Setup Codes for
Amplifiers
Cable Converters
Cassette Players
CD Players
DAT Players
Satellite Receivers
DVD Players
Home Automation
Laser Disc Players
Miscellaneous Audio
Phonographs
Tuner/Receivers
2?
hatntnxtnxthxtatatit
Once the 7-in-One is operating all of your devices, press ESCAPE to stop
programming.
A LOOK AT YOUR REMOTE CONTROL
AMP, TUNER, TV, CBL, CD, VCR, SAT,
-Iet you select the device you want to control.
PLUG ‘N POWER — allows you to control lamps and appliances with your 7-in-One
IR/RF Remote Control, This feature requires additional equipment that is available
at your local RadioShaek store.
HOME THEATER- lets you control all the functions of a home theater system.
POWER~ turns the remote on and off, and controls ALL LIGHTS ON in the PLUG ‘N
POWER mode
Note: The PLUG ‘N POWER feature requires additional equipment that is available at
your local Radio Shack store,
MENU- works like the Menu or OSD (on-screen display) key on your original remote.
Use T, iv, —>, and <- (Menu Up, Down, Right, and Left) to navigate your on-screen
menus. If your original remote had a Select key to select menu options, use SELECT in
its place. Use CLEAR (SHIFT + SELECT) to exit/clear menus. See your device’s
original owner’s manual for more detailed instructions on using menus.
Notes:
0 T, l, —>, and <— also control the Rear Level +/- and Balance Right/Left functions in
AMP or TUN mode, and Disc +/- and Track +/— in CD mode.
0 SELECT also controls Tape Mon in AMP or TUN mode, Disc Select in CD mode,
and the Fetch function in the on-screen menu of an RCA satellite system.
PROGRAM (SHIFT + MENU) — operates your satellite system‘s and cable converter‘s
Guide function, as well as any devices secondary menus.
SURROUND — operates the surround mode. It also operates the favorite channel
function in SAT and CBL modes, 10+ (to access tracks numbered higher that 10) in CD
mode, and the DISC function of a laser disc playeri
SHIFT f besides those functions described elsewhere in this manual, works with these
keys to control advanced features:
Mode Key Function
VCR PLAY SLOW
REW REW SLOW (SLOW -)
FFWD FFWD SLOW (SLOW +)
STOP EJECT
PAUSE X2
Satellite Receiver T AUDIO +
l AUDIO »
Receiver/Tuner/Amplifier T CENTER LEVEL +
l CENTER LEVEL -
—} DELAY +
+— DELAY -
Laser disc/Cassette/DVD PLAY REVERSE PLAY
REW REW SLOW
FFWD FFWD SLOW
STOP EJECT
PAUSE X2
CD STOP EJECT
ESCAPE f lets you exit the remote’s displayed menu.
CENTER and REAR (SHIFT + CENTER) — work like the Add and Delete keys on
your original TV remote, the DISC A and B keys on your laser disc remote, or the SAT
and AUDIO keys of a satellite system remotes
VOL + (Volume Up), VOL — (Volume Down) and MUTE — control the volume like the
Volume Up and Down and Mute keys on your original remote. In the PLUG ‘N POWER
mode, VOL + / VOL — operates Bright and Dim and MUTE operates ALL OFF.
Note: The PLUG ‘N POWER feature requires additional equipment that is available at
your local Radio Shack store
SLEEP (SHIFT + MUTE) — controls the Sleep Timer in TV, CABLE, SAT, and AMP
or TUN modes for devices which have this feature, If your device does not have a Sleep
Timer, SLEEP activates the remote’s built-in sleep timer.
CH + (Channel Up) and CH — (Channel Down) - work like the Channel Up and Down
keys on your original remote CH + and CH — also control preset Up/Preset Down in
AMP or TUNER mode and ON/OFF in the PLUG ‘N POWER mode,
Note: The PLUG ‘N POWER feature requires additional equipment that is available at
your local Radio Shack store.
Digit keys (0-9) — work like the digit keys on your original remotes They also control
Input Selections in AMP or TUNER mode.
ENTER » works like the Enter key on your original remote (for example, direct channel
access).
TV/VIDEO 7 works like the TV/Video key on your original TV remote, and TV/SAT
key on your original satellite remote, TV/VIDEO also controls TV/VCR in VCR mode,
A/B in cable and CD modes, and Input Select in AMP or TUN mode.
LAST (Last Channel) — works like the Previous Channel or Recall key on your original
remote. It also operates the RANDOM functions in the CD and AMI> or TUNER modes.
AUDIO and VIDEO (Macro Keys) — memorize up to 15 keystrokes, so you can repeat
them in sequence in any mode at the press ofa single key.
REW (Rewind), PLAY, FFWD (Fast Forward), REC (Record), STOP, and PAUSE —
work like the transport keys on your original VCR or Laser Disc player remotes. To
guard against accidental recording, you must press REC twice before recording,
PIP — controls your TV or VCR’s Picture-in-Picture feature. Works like the VIEW key
on your Satellite receiver‘s remote,
FREEZE (SHIFT + PIP) - freezes your Picture-in-Picture window.
SWAP ~- swaps the Picture-in-Picture window and the main picture.
FAV/SCAN (Scan or Favorite Channel Scan) -— can be programmed to scan through your
ten favorite channels or left un-programmed to scan all channels.
MOVE — moves the Picture-in-Picture window around the screen Works like the Nest
key on your satellite receiver’s remote,
(LITE BULB GRAPHIC) — lets you tum the remote’s backlight and display on and of£
When you press (lite bulb graphic) to turn on the backlight, the backlight stays lit for 5
seconds then lights again anytime you press a key, To turn off the backlight feature,
press (lite bulb graphic) againr
P — lets you use the remote’s displayed menu to program your 7-in-One.
SETTING UP YOUR REMOTE CONTROL
Note: For the best operation, you should be within 15 feet ofthe device you want to
operate.
TO OPERATE YOUR TV
Locate the codes for your TV in “Setup Codes for TV’S" on page 4 _and write them
down on the supplied label.
Notes: Some manufacturers have several codes listed. Try each until you find the right
one, The brands are listed in Alphabetical order, with the most popular codes listed first
Then follow these steps to program the 7-in—One to operate your TV.
1. Tum on your TV.
2, Press TV then hold down P until TIMES SEQ appears.
3. Press i. CODE SETUP appears.
4. Repeatedly press SELECT until TV appears.
5. Enter the first four-digit code listed for your TV’s brand, then press SELECT.
Note: If the 4-digit code begins with zero, only the last 3-digits will appear on the
display.
6. Point the 7-in—One at your TV and press POWER. Your TV should turn off, If it
does not, enter the next code from the list and press SELECT then POWER again.
When your TV turns off, press ESCAPE to stop programming.
Setup Codes for TV’s
lO
TO OPERATE YOUR VCR
Locate the codes for your VCR in “Setup Codes for VCR s on page 7 _ and write them
down on the supplied label,
Notes: Some manufacturers have several codes listed. Try each until you find the right
one, The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-0ne to operate your VCR.
I. Turn on your VCR and insert a tape.
2. Press VCR then hold down P until TlMES SEQ appears
3. Press in CODE SETUP appears.
4. Repeatedly press SELECT until VCR appears.
5. Enter the first four—digit code listed for your VCR‘s brand, then press SELECT.
Note: If the 4-digit code begins with zero, only the last 3-digits will appear on the
display.
6. Point the 7-in-One at your VCR and press POWER or PLAY. Your VCR should
turn off or start to play. If it does not, enter the next code from the list and press
SELECT then POWER or PLAY again. When your VCR turns off or plays, press
ESCAPE to stop programming.
Setup Codes for VCR’s
ll
TO OPERATE YOUR TV/V CR COMBINATION
Locate the codes for your TV/VCR Combination in “Setup Codes for TV/VCR
Combinations” on page A _ and write them down on the supplied label.
Notes: Some manufacturers have several codes listed. Try each until you find the right
one, The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-One to operate your TV/VCR Combination.
l.
2.
Turn on your TV/VCR Combo and insert a tape.
Press VCR then hold down P until TIMES SEQ appears.
Press i. CODE SETUP appears.
Repeatedly press SELECT until VCR appears.
Enter the first four-di git code listed for your TV/V CR Combo’s brand, then press
SELECT.
Note: If the 4-digit code begins with zero, only the last 3-digits will appear on the
display.
Point the 7-in-One at your TV/VCR Combo and press POWER or PLAY. Your
TV/VCR Combo should tum offor start to play. [fit does not, enter the next code
from the list and press SELECT then POWER or PLAY again. When your
TV/VCR Combo turns off or plays, press ESCAPE to stop programming.
Note: Some TV/VCR combinations require a second code to control volume. If you can
not get the volume to work, use the TV code listed in the “Setup Codes for TV/VCR
combinations“ on page _ _.
Setup Codes for TV/V CR Combinations
I2
TO OPERATE YOUR CABLE CONVERTER
Locate the codes for your cable converter in “Setup Codes for cable converters" on page
gand write them down on the supplied label.
Notes: Some manufacturers have several codes listed. Try each until you find the right
one. The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-One to operate your cable converter.
I. Turn on your cable converter,
2. Press CBL then hold down P until TIMES SEQ appears.
3, Press l. CODE SETUP appears.
4. Repeatedly press SELECT until CABLE appears.
5, Enter the first four-digit code listed for your cable converter’s brand, then press
SELECT.
Note: If the 4-digit code begins with zero, only the last 3-digits will appear on the
display.
6. Point the 7-in-One at your cable converter and press POWER, Your cable converter
should turn off, If it does not, enter the next code from the list and press SELECT
then POWER again, When your cable converter turns off, press ESCAPE to stop
programming
Note: If your original cable converter remote does not have an ON key, press CH+ on
the 7-in-Onc to turn on your cable converter.
Setup Codes for Cable Converters
TO OPERATE YOUR SATELLITE RECEIVER
Locate the codes for your satellite receiver in “Setup Codes for Satellite Receivers“ on
page 7 ‘and write them down on the supplied label.
Notes: Some manufacturers have several codes listed. Try each until you find the right
one. The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-One to operate your satellite receiver.
1, Turn on your satellite receiver.
2. Press SAT then hold down P until TIMES SEQ appears.
3. Press in CODE SETUP appears.
13
4. Repeatedly press SELECT until SAT/DSS appears.
5. Enter the first four-digit code listed for your satellite’s brand, then press SELECT.
Note: lfthe 4-digit code begins with zero, only the last 3»digits will appear on the
display.
(7. Point the 7-in-One at your satellite receiver and press POWER. Your satellite
receiver should turn off. Ifit does not, enter the next code from the list and press
SELECT then POWER again. When your satellite receiver turns off. press
ESCAPE to stop programming.
Setup Codes for Satellite Receiver
TO OPERATE YOUR CD PLAYER
Locate the codes for your CD player “Setup Codes for CD Players” on page _ fand write
them down on the supplied label.
Notes: Some manufacturers have several codes listed. Try each until you find the right
one, The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-One to operate your CD player.
1. Tum on your CD player and insert a disc.
2. Press CD then hold down P until TIMES SEQ appears.
3. Press i. CODE SETUP appears.
4. Repeatedly press SELECT until CD appears.
5. Enter the first four-digit code listed for your CD player‘s brand, then press SELECT,
Note: If the 4-digit code begins with zero, only the last 3-digits will appear on the
display.
6. Point the 7-in—One at your CD Player and press PLAY. Your CD player should start
to play. If it does not, enter the next code from the list and press SELECT then
PLAY again. When your CD starts to play, press ESCAPE to stop programming.
Setup Codes for CD Players
I4
TO OPERATE YOUR TUNER/RECEIVER
Locate the codes for your Tuner/Receiver in “Setup Codes for Tuners/Receivers” on page
_and write them down on the supplied label.
Notes: Some manufacturers have several codes listed. Try each until you find the right
one. The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-One to operate your Tuner/Receiver.
1, Turn on your Tuner/Receiver.
2. Press TUNER then hold down P until TIMES SEQ appears.
3. Press iv. CODE SETUP appeals
4. Repeatedly press SELECT until TUNER appears.
5. Enter the first four-digit code listed for you tuners/receiver’s brand, then press
SELECT.
Note: Ifthe 4-digit code begins with zero, only the last 3-digits will appear on the
display.
6. Point the 7-in-One at your Tuner/Receiver and press POWER. Your Tuner/Receiver
should tum off. If it does not, enter the next code from the list and press SELECT
then POWER again. When your TunerfReceiver turns off, press ESCAPE to stop
programming.
Setup Codes for Tuners/Receivers
15
TO OPERATE YOUR AMPLIFIER
Locate the codes for your Amplifier in “Setup Codes for Amplifiers“ on page _ vand
write them down on the supplied label,
Notes: Some manufacturers have several codes listed. Try each until you find the right
one. The brands are listed in Alphabetical order, with the most popular codes listed first.
Then follow these steps to program the 7-in-0ne to operate your amplifier.
7. Turn on your amplifier.
8. Press AMP then hold down P until TIMES SEQ appears.
9, Press i. CODE SETUP appears.
lO. Repeatedly press SELECT until AMP appears
11. Enter the first four-digit code listed for your amplifier’s brand, then press SELECT.
Note: lfthe 4-digit code begins with zero, only the last 3-digits will appear on the
display.
12. Point the 7-in-One at your amplifier and press POWER Your amplifier should turn
off. If it does not, enter the next code from the list and press SELECT then POWER
again. When your amplifier turns off, press ESCAPE to stop programming,
Setup Codes for Amplifiers
16
TO OPERATE OTHER DEVICES
In addition to the labeled devices (AMP, TUNER, TV, CD, CBL, VCR or SAT), the 7-
in-One can also operate laser disc players (LPD), cassette decks, digital audio tape (DAT)
players, video accessories, and miscellaneous audio devices (graphic equalizers and
digital audio service terminals for example).
To access device codes for: Use:
Digital Video Disc Players, Laser Disc VCR
Players, Cassette Decks, Digital Audio
4T_ape Players
Phonographs CD
Video Accessories CBL
Miscellaneous Audio AMP
Home Automation
PLUG ‘N POWER
Note: The PLUG ‘N POWER feature requires additional equipment that is available at
your local Radio Shack store.
For example, to set up a laser disc player:
1. Turn on your laser disc player and insert a disc
2. Press VCR then hold down P until TIMES SEQ appears,
3. Press t. CODE SETUP appears.
4, Repeatedly press SELECT until VCR appears
5 Press l or T to toggle between VCR, LDP, TAPE, and DAT.
6. When LDP appears, enter the first four-digit code listed for your laser disc player‘s
brand in “Setup Codes for Laser Disc Players" on page _ _, then press SELECT,
Note: If the 4-digit code begins with zero, only the last 3-digits will appear on the
display.
7. Point the 7-in-One at your laser disc and press PLAY, Your laser disc player should
play. lt‘it does not, enter the next code from the list and press SELECT then PLAY
again, When your laser disc player plays, press ESCAPE to stop programming,
I7
Setup Codes
SPECIAL FEATURES
SEARCHING FOR A CODE
Before Setup
If you have tried all the codes from the list and your device still will not respond to the 7-
in-One (or if your brand is not listed), try searching for your code.
For example, to find the code for your TV:
I. Turn on your TV, then press TV.
2. Hold down P until TIMED SEQ appears.
3. Press i. CODE SETUP appears.
4. Press SELECT. DEV SET UP appears.
5. Press l. DEV SEARCH appears.
6. Press SELECT. TV and the last entered four-digit code appear,
Note: Ifthe 4-digit code begins with zero, only the last 3
Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 1999:08:02 09:18:06
Creator                         : Photoshop PDF Plug-in 1.0
Producer                        : Photoshop PDF Plug-in 1.0
Create Date                     : 1999:07:01 19:24:00
Page Count                      : 29
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AAO1501995

Navigation menu