Radio Shack 2000314 Scanning receiver User Manual manual

RadioShack Corporation Scanning receiver manual

manual

Download: Radio Shack 2000314 Scanning receiver User Manual manual
Mirror Download [FCC.gov]Radio Shack 2000314 Scanning receiver User Manual manual
Document ID64609
Application IDLEpSOQBRIPW6BNkjpUXunQ==
Document Descriptionmanual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize105.52kB (1318997 bits)
Date Submitted1999-10-18 00:00:00
Date Available2000-01-06 00:00:00
Creation Date1999-10-18 09:34:30
Producing SoftwareAcrobat 4.0 Scan Plug-in for Windows
Document Lastmod1999-10-18 09:42:06
Document Titlemanual
Document CreatorAcrobat 4.0 Scan Plug-in for Windows

20-314 Owner‘s Manual Draft
Cat. No. 20-314
OWNER’S MANUAL
Please read before using this equipment.
PRO—79
ZOO—Channel Portabie Scanner
RadioShack
Page 1
204514 Owner's Manual Draft,
INTRODUCTlON
Your new HadloShack PRO-79 200-Channel Portable Scanner lets you in on all the action.
This scanner gives you direct access to over 25,000 excitmg frequencres, including police
and fire departments, ambulance SeNlCeS, and amateur radio services, You can select up to
200 channels to scan. and you can change your selection at any time.
The secret to your scanner’s ability to scan so many lrequenctes is its customdesigned
mlcroprocessor~ a tiny, built-in computer. Your scanner also has these special features:
Four Sen/ice Banks — let you search preset frequencies in separate fire/police, air, ham
radio, and marine banks. to make lt easy to locate specific types of calls.
Two-Second Scan Deley— delays scanning for 2 seconds before movrng to another channel,
so you can hear more replies.
Ten Channel-Storage Banks — you can store up to 20 channels in each oi 10 different banks,
to group channels so you can more easily identify calls.
20 Monitor Memories — let you temporarily save up to 20 frequencies you locate during a
search, so you can move selected trequencres to channel storage later.
Memory Backup — keeps the channel frequencies stored In memory {or about 1 hour during
a power loss.
HeperSearch TM and HyperScan TM — let you set the scanner to search at up to 50 steps
per second and scan at up to 25 channels per second, to help you quickly find interesting
broadcasts
Duplicate Frequency Check — automatically notifies you if you are about to store a frequency
you have already stored. to help avoid wasting storage space.
Direct Search _ lets you search for new and unlisted frequencies starting lrorn a specified
frequency.
Page 2
20314 Owner’s Manual Draft
Priority Channel ~ lets you designate a channel to be scanned every two seconds so you do
not miss important calls.
Weather Band Key — scans 7 Dre-programmed weather lrequencies to keep you informed
about correct weather conditions.
Weather Alert — automatlcally sounds the alarm tone to advise cl hazardous weather
conditions when it detects the alert signal on the local NOAA weather channel.
Lock-Out Function — lets you set your scanner to skip over specified channels or
frequencies when scanning or searching.
Key Lock — lets you lock the scanner‘s keys to help prevent accidentally changing the
scanner's programming
Flexible Antenna with BNC Connector — provides excellent reception and is designed to
help prevent antenna breakage.
Liquid Crystal Display — makes it easy to view and change programming information,
Display Backlight— makes the scanner easy to read in low light situations.
Three Power Options — let you power the scanner from internal batteries (non-rechargeable
batteries, rechargeable batteries, or external AC or DC power (using optional adapters)
(c) 1999 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
Hypersearch and Hyperscan are trademarks used by Tandy Corporation.
We recommend you record your scanner's serial number here. This number is on the
scanner’s back panel.
Serial Number
Page 3
20-314 Owner's Manual Draft
Your PRO-79 scanner can receive all oi these frequencies:
29-54 MHZ
108-1 36.9875 MHZ
. 137-174 MHZ
. 380-512 MHZ
This Owner‘s Manual also includes the section “A General Scanning Guide” to help you
target frequency ranges in your service area so you can search for a wide variety of
broadcasts.
FCC N OTIC E
Your scanner might cause TV or radio interlerenoe even when it is operating properly To
determine whether your scanner is causrng the interference, turn off your scanner. If the
interference goes away, your scanner is causing the interference. Try the following methods
to eliminate the interference.
. Move your scanner away from the TV or radio.
. Connect your scanner to an outlet that is on a different electrical circuit from the TV or
radio.
. Contact your local HadioShack store tor help.
It you cannot eliminate the interference, the FCC requires that you stop ustng your scanner.
ThlS devtce complies with Part is of the FCC Rules. Operation is subject to the following
conditions: (i) This device must not cause harmful interference. and (2) this device must
accept any interference received, including interlerence that may cause undesired
operation.
Note: Mobile use of this scanner is unlawful or requires a permit in some areas. Check the
laws in your area.
Page 4
20314 Owner’s Manual Draft
SCANNING LEGALLY
Scanning is a fun and interesting hobby. You can hear police and fire departments,
ambulance services, government agencies, private companies, amateur radio services,
aircraft, and military operations. It is legal to listen to almost every transmission your
scanner can receive. However, there are some electronic and wire communications that are
illegal to intentionally intercept. These include:
. telephone conversations (cellular, cordless, or other private means of telephone Signal
transmission)
. pager transmissions.
. scrambled or encrypted transmissions
According to the Federal Electronic Communications Privacy/Act (ECPA), as amended, you
could be fined and possible imprisoned tor intentionally listening to, using, or disclosing the
contents of such a transmisSion unless you have the consent of a party to the
communication (unless such activity is otherwise illegal). These laws change from time to
time and there might be state or iocal laws that also affect legal scanner usage.
Page 5
20-314 Owner’s Manual Draft
CONTENTS
wiH add
Page 8
205314 Owner’s Manual Draft
PREPARATION
POWER SOURCES
You can power your scanner from any of three sources:
. internal batteries (not supplied — see “Using Batteries”)
. standard Ac power (With an optional AC adapter — see “Usmg Standard AC Power” on
Page XX)
. vehicle battery power (with an optional Dc adapter— see ‘Using Vehicle Battery Power“ on
Page XX)
Notes:
. Connecting an AC or DC adapter to the scanner disconnects internal batteries when you
use the supplied non-rechargeable battery holder, but it does not disconnect internal
batteries when you use the supplied rechargeable battery holder.
. it you install the rechargeable battery holder. you can operate the scanner and recharge
the rechargeable batteries at the same time. See ‘Using Batteries“ and “Charging
Rechargeable Batteries" on Page XX.
. It the scanner stops working properly alter connecting it to power, try resetting it. See
“Hesetting/lnitializtng the Scanner” on Page XX.
Using Batteries
You can power the PRO-79 With four AA batteries. For the longest operation and best
performance, we recommend alkaline batteries, available at your local RadioShack store.
You can use either the supplied non-rechargeable black battery holder, or the supplied
rechargeable yellow battery holder. If using Ihe rechargeable battery holder, we recommend
nickelcadmium batteries or nickel-metal hydride batteries.
Warning: Never install non-rechargeable batteries in the rechargeable battery holder. Non—
rechargeable batteries can get hot or explode it you try to recharge them.
Page 7
207314 Owner‘s Manual Draft
Note: You must charge rechargeable batteries before using either the first time. See
“Charging Rechargeable Batteries“ on Page XX.
Follow these steps to install batteries.
1. Press down on the battery compartment cover on the rear of the scanner and slide the
cover in the direction at the arrow to remove it.
add illustration.
2. Pull up the battery holder out of the battery compartment.
add illustration.
3. it you are installing individual batteries, insert tour AA batteries in the battery holder as
indicated by the polarity symbols [+ and ») marked on the holder.
Cautions:
i Use only fresh batteries ol the required size and recommended type.
Always remove old or weak batteries. Batteries can leak chemicals that destroy electronic
circuits.
Do not mix old and new batteries, diflerent types ol batteries {alkaline or rechargeable), or
rechargeable batteries ol different capacities.
4. Put the battery holder into the compartment.
add illustration.
Caution: Meet the battery compartment and battery holder’s metal contact.
5. Replace the cover.
When battery power is low. El appears and the scanner beeps continuously. When battery
power iS exhausted, the scannerturns itself off. Replace all four non»rechargeable batteries,
or recharge the rechargeable batteries. See “Changing Rechargeable Batteries' on Page
XX.
Page 8
20-314 Owners Manual Draft
Caution: Always dispose ol old batteries promptly and properly. Do not bury or burn them.
Usmg Standard AC Power
To power the scanner from AC power, you need AC adapter (Cat. No. 273-1767 & 273-
1706)
Warning: Do not use an AC adapters polarized plug with an extension cord, receptacle, or
other outlet unless the blades can be fully inserted to prevent blade exposure.
Cautions:
. You must use an AC adapter that supplies 9 volts and delivers at least 300 milllamps. lt
center tip must be set to negative, and its plug rnust correctly fit the ecanner’s PWFt jack
The recommended adapter meets these speleications. Using an adapter that does not meet
these specifications could damage the scanner or the adapter.
. When you flhish using the AC adapter, disconnect it from the AC outlet first, then
disconnect it from the scanner.
Plug the adapter's 1.7 mm inner dlamelerl4.75 mm outer dlameter barrel plug into the
scanners PWH lack. Then plug the adapters power module into a standard AC outlet.
add illustration.
Using Vehicle Bafiery Power
To power the scanner from your vehlcle’s cigarette-lighter socket, you need a DC adapter.
such as Cat. No 273-1810.
Cautions:
. You must use a DC adapter that supplies (regulated) 10 volts and delivers at least 300
milliamps. Its center tip must be set to negatlve, and its plug must correctly fit the scanner‘s
F’WFi Jack. The recommended adapter meets these specifications, Using an adapter that
does not meet these specifications could damage the scanner or the adapter.
Page 9
20-314 Owner’s Manual Draft
. To protect your vehicle’s electrical system, always plug the adapter into the scanner before
you plug it into your vehicle’s Cigarette-lighter socket. Always unplug the adapter trcm the
vehicle’s cigarette-lighter socket before you unplug it from the scanner.
add illustration
1. Connect the DC adapter’s 1.7 mm inner diameter/4.75 mm cuter drameter barrel plug to
the adapters cable. with the trp set to negative.
2. Set the adapter‘s voltage switch to 10V.
3. Insert the barrel plug into the scanner’s PWRjack
4. Plug the other end of the adapter into your vehicle‘s cigarette-lighter socket.
Note: It the scanner does not operate properly when you connect a DC adapter, unplug the
adapter from the cigarette-lighter socket and clean the socket to remove ashes and other
debrls.
Charging Rechargeable Batteries
Your scanner has a built-in charging circuit that lets you charge rechargeable battenes while
it is in the scanner. To charge rechargeable batteries, simply connect an appropriate AC or
DC adapter to the PWR lack.
it takes between 14—16 hours to recharge rechargeable batteries that is luIIy discharged.
You can operate the scanner while recharging the rechargeable batterres, but charging
takes longer.
Note: Rechargeable batteries last longer and deliver more power if you occasionally let them
fully discharge. To do this, Simply use the scanner until B appears on the display. Then lully
charge the rechargeable batteries.
Page 10
20-314 Owner’s Manual Draft
important: At the end of a rechargeable battery's useful life. it must be recycled or disposed
of properly. Contact your local. county. or state hazardous waste management authorities for
information on recycling or disposal programs in your area. Some options that might be
available are: municipal curb-Side collection, dropctl boxes at retailers such as your local
HadloShack store. recycling ootleciion centers. and mail»back programs.
CONNECTING THE ANTENNA
Follow these steps to attach the supplied flexible antenna to the antenna jack on the top 01
your scanner.
add illustration.
1. Align the slots around the antsnna‘s connector with the tabs on the antenna jack.
2. Press the antenna down over the jack and turn the antenna‘s base dockwise until it looks
into place.
Connecting an Optional Antenna
The antenna connector on your scanner makes it easy to use the scanner with a variety of
antennas. such as an external mobile antenna or outdoor base station antenna. Your local
RadioShack store sells a variety of antennas.
Always use 50-ohm coaXial cable, such as FlG-58 or RG-s. to connect an outdoor antenna.
For lengths over 50 feet. use FlG-B low~|oss dielectric coaxial cable. I! your antenna‘s cable
does not have a ENC connector) you will also need a BNC adapter (also available at your
local RadioShack store).
Follow the installation instructions supplied with the antenna. route the antenna cable to the
scanner, then connect it to the antenna jack.
Warning: Use extreme caution when installing or removing an outdoor antenna. lf the
antenna starts to tall, let it gol It could contact overhead power lines. It the antenna touches
a power line, contact With the antenna, mast, cable or guy wires can cause electrocution and
death! Call the power company to remove the antenna. Do not attempt to do so yourself.
Page 11
20-314 Owner’s Manual Draft
CONNECTING AN EARPHONEiHEADPHONES
For private listening, you can plug an earphone or mono/stereo headphones (such as Cat.
No. 33-177 or 20-210) into the (headphone symbol) jack on top ot your scanner. This
automatically disconnects the internal speaker.
add illustration.
Listening Safely
To protect your hearing. follow these guidelines when you use an earphone or headphones:
. Do not listen at extremely high volume levels. Extended high-volume listening can lead to
permanent hearing loss.
. Set the volume to the lowest setting before you begin listening, After you begin listening.
adjust the volume to a comfortable level.
. Once you set the volume, do not increase it. Over time, your ears adapt to the volume level,
so a volume level that does not cause discomtort might still damage your hearing.
Traffic Safety
Do not wear an earphone or headphones while you drive a vehicle or ride a bicycle. This can
create a traffic hazard and can be illegal in some areas.
Even though some earphones and headphones let you hear some outside sounds when
you listen at normal levels, they still can present a traffic hazard.
Page 12
20314 Owner’s Manual Draft
CONNECTING AN EXTENSION SPEAKER
In a noisy area. an amplified speaker (such as Cal. No. 21-541} might provide more
comfortable sttening. Plug the speaker cabie's 1IS-inch (3.5 mm) mini-pug into your
scanner‘s [headphone symbm} Jack.
add iHustratwon.
USING THE BELT CLIP
You can use the belt dip attached to the back ol the scanner for hands-tree carrying when
you are on the go. Simply slide the bell cup over your belt or waistband.
Page 13
20314 Owner’s Manual Draft
UNDERSTANDiNG THE PRO~79
Once you understand a few simple terms used in this manual and familiarlze yourself with
your scanner‘s features, you can put the scanner to work for you. You simply determine the
type of communications you want to receive, then set the scanner to scan them.
A frequency is the tuning location of a station (expressed in kHz or MHz). To find active
frequencres, you can use the search tunction.
You can also search the sewioe-search banks. which are preset groups of frequencies
categorized by type of serVice.
When you find a frequency. you can store it into a programmable memory location called a
channel, which is grouped with your other channels in a channslvslorage bank. You can then
scan the channelstorage banks to see it there is activity on the frequenmes stored there.
Each time the scanner finds an active frequency, it stays on that channel until the
transmission ends.
A LOOK AT THE KEY PAD
Your scanner’s keys mighl seem confusmg at first, but this information should help you
understand each key’s1unction.
add illustration.
BAND—lets you search preprogrammed service banks.
PRI/ALERT—turns the priority iunctron on and off, or sets the WX alert mode.
wxfscans through the 7 pro-programmed weather channels.
SCAN—scans through the programmed channeis.
MANUAL—stops scanning and lets you directly enter a channel number.
A and V—begins searching up or down (or active frequencies or selects the derection
when you scan channels.
L/O RVW, L/O—Iets you review locked-out frequencies, or lets you lock out selected
Page 14
20-314 Owner's Manual Draft
channels/trequencles so they will not be scanned or searches.
MON/CL—acoesses the 20 monitor memories or clears an incorrect entry.
Tr°lLlGHT —Iockslun|ocks the keypad to prevent accidental entries (without SCAN,
MAN, and LIGHT key]. or turns the display’s backlight on or ofl.
PG M—programs ireque ncies into channels.
Number Keys—each key has a single-digit label and a range of numbers. Use the digits on
the keys to enter the numbers tor a channel or a frequency. Use the range of numbers
above the key (21 410. for example) to select the channel in a channel-storage Dank. See
“Understanding Sen/toe Banks/Banks/Memories "
DELAYL—programs a 2—second delay lor the selected channel, or enters a decimal point
(necessary when programming frequencies).
ENTER—enters frequencies into channels.
A LOOK AT THE DISPLAY
The display has indicators that show the scanner‘s current operation. A quick look at the
display Will help you understand how to operate your scanner.
add illustration.
fro — appears when you lock the keypad.
BANK — appears With numbers (1—10). Bani-r numbers With a bar under them show which
ones are turned on tor scanning. See “Understanding Service Banks/Banks/Memories."
MFtN — appears when you search the marine service bank.
WX — appears when you scan the weather channels.
FD/PD — appears when you search the tirelpolice service bank.
AlR — appears when you search the air service bank.
HAM — appears when you search the ham radio service bank.
A or V — indicates the search or scan direction.
M — llashes with a number (1-20) to show which monitor memory you are listening to.
OH — the digits that precede this indicator (1-200 and P) show which channel the scanner is
turned to.
B — appears when the batteries are low.
L/O — appears when you manually select a channel you looked out while scanning or you
Page 15
20-314 Owner's Manual Draft
review a locked out frequency.
SRCH — appears during service bank and direct lreguency searches.
SCAN — appears when you scan channels.
MAN — appears when you manually select a channel.
PGM — appears while you program frequencies into the scanner‘s channels.
PHI — when you turn on the priority teature.
DLY - appears when you program a 2-second delay.
Error — appears when you make an entry error.
-dUPL- — appears when you try to store a frequency that is already stored in another
channeL
-d- - appears during a direct frequency search.
-b- — appears during a service bank frequency search,
Ch-FULL — appear when you try to enter a frequency during a search when all channels are
full.
F L—oul — appears when you start direct search lrorn a locked out frequency
FLo -FULL — appears when you try to lockout a frequency during a search when 50
frequencies are already locked out.
L-r — appears when you review the lockout frequenCies.
dEFAULt — appears when you remove all the locked out from the service bank irequencies.
FLo ALL-CL — appears when you remove all the locked out frequencies during a service
bank/direct search.
F — when the scanner is tuned to a priority channel.
ALErt — appears when the scanner is watching the WX alerl lone.
WirEd — appears when you turn on the wired programming mode.
StArl — appears when the scanner start wired programming.
C-Error — appears when the scanner receive check sum error during wired programming.
D-Error — appears when the scanner finds data error during wired programming.
End — appears when the scanner finishes wired programming.
OFF tonE — appears when you set the key lone off.
ON ronE — appears when you set the key tone on.
Page 16
20-314 Owner‘s Manual Draft
UNDERSTANDING SERVICE BANKS/BANKSIMEMORIES
Service Bank
The scanner is preprogrammed with the frequencies allocated by firelpoiice. aircraft. ham
radio, and marine services. In mese service banks, you can search through the frequencies
and store them in channeis for fire/poiice, aircraft, ham radio, and marine banks. This is
handy for quickiy finding active frequencies instead of searching through an entire band.
Note: The frequencies in the scanner’s service bank are preset. You cannot change them.
Fire/Poiice
Group Frequency range (MHz)
1 31420-33980
37320-37420
39020-39880
42020-42940
44.520~45.860
45.880
45.900
45940-45050
46080416500
2 153.770-154.130
154 145-1 54.445
154.650-1 54.950
155.010-155.370
155.415-155700
1557304 55210
158730459210
166.250
170.150
3 453.0375-453 9625
4580375458955
460.01 2541605375
46501 2541555375
Page 17
Step (kHz)
20
20
20
20
40
40
20
60
15
15
60
15
60
60
12.5
12.5
12.5
12.5
20- 314 Owner's Manual Draft
Air
Frequency range (MHz) Step (kHz)
108.000-136 9875 12.5
Amateur Radio
Group Frequency range (MHz) Step (kHz)
1 2900029700 5
2 50.000-54 000 5
3 144000148000 5
4 4200004350000 125
Marme
Channel Frequency (M Hz)
06 156.3000
07 1563500
08 156.4000
09 1 56.4500
10 156.5000
11 156.5500
12 156.6000
13 1566500
14 155.7000
15 156.7500
15 156.8000
17 1568500
18 156.9000
19 156.9500
20 157 0000/1 61 .6000
21 1570500
22 157.1000
213 157.1500
24 15720001161 £000
25 1 57.250011613500
26 15730001161 9000
27 15?.3500}161.9500
28 157400011620000
Page 18
20-314 Owner's Manual Draft
64 156.2250
65 1562750
66 1 56.3250
67 156.3750
68 156.4250
59 156.4750
70 156.5250
71 1565750
72 156.8250
73 155.6750
74 156.7250
77 156.8750
78 156.9250
79 156.9750
80 157.0250
81 157.0750
82 157.1250
83 157.1750
84 157.22501161.8250
85 157.275011513750
86 157.32501161.9250
87 157.375011613750
88 1 57.4250
Channel—Storage Banks
To make it easier to identify and select the channsts you want to listen to, channels are
divided into 10 banks of 20 channels each. Use each channel-storage bank to group
frequenmes, such 5 those used by the police department, fire department, ambulance
sen/ices, or aircraft (see “Gurde to the Action Bands” on Page XX). For example, the police
department might use four frequencies, on for each side of town. You could program the
police frequencies starting wrth Channel 1 (the first channel in bank 1] and program the fire
department frequencies starting with Channel 21 (the first channel in bank 2).
Page 19
20-314 Owner’s Manual Draft
Monitor Memories
The scanner aiso has 20 monitor memories that you can use to temporariiy store
frequencies while you decide whether to save them into channeisu This is handy for quickly
staring an aciive frequency when you are searching through an entire band. You can store a
frequency into a monitar memory during a service bank‘ or direct search. See ‘Finding and
Storing Active Frequencies,”
You can select monitor memories manuaily. bul you cannot scan |hem. See “Listening to
Monitor Memories,”
Page 20
20314 OWner's Manual Draft
OPERATION
TURNING ON THE SCANNEFUSETTING VOLUME AND SQUELCH
1 Turn SQUELCH fully counterclockwise until the indicator points to MIN before you turn on
the scanner.
add Illustration.
2 To turn on the scanner. turn VOLUME clockwise until you hear a hissing sound.
3 Turn SOUELCH clockwise. just until the hissing sound stops,
Notes:
To listen to a weak or distant station, turn SQUELCH counterclockwise. It reception is poor.
turn SQUELCH clockwise to cut out weak transmissions.
. It SQUELCH is adiusted so you always hear a hissmg sound. the scanner does not scan or
search properly.
4. To turn off the scanner when you tinish, tum VOLUME counterclockwtse to OFF.
STORING KNOWN FREOENCIES iNTO CHANNELS
Good references lor active lrequenees are the RadioShack Police Call. Aeronautical
Frequency Directory, and Maritime Frequency Directory. We update these directories every
year, so be sure to get a current copy,
Follow these steps to store frequencies into channels.
1. Press PGM, enter the channel number (1—200) where you want to store a frequency,
then press PGM again. The channel number appears.
Page 21
20-314 Owner's Manual Draft
2. Use the number keys and . to enter the frequency (including the decimal potnt) you want
to store
add illustration.
3. Press ENTER to store the frequency into the channel.
Notes:
. it you made a mistake in Step 2, Error appears and the scanner beeps when you press
ENTER. Simply start again from Step 2.
. Your scanner automatically rounds the entered frequency down to the closest valid
frequency. For example, ii you enter a frequency for 151.473, your scanner accepts it as
151.470.
if you entered a frequency that is already stored in another channel, the scanner beeps
three times and displays the lowest channel number where the frequency is already stored.
and -dUPL—, then the frequency flashes. If you want to store the frequency anyway, press
ENTER again. Press MONICL to clear the frequency.
. Press DELAY if you want the scanner to pause 2 seconds on this channel atter a
transmission ends before it proceeds to the next channel (see “Using the Delay Function" on
Page XX). The scanner also stores this setting in the channel.
4. To program the next channel in sequence. press PGM and repeal Steps 2 and 3,
FINDiNG AND STOFiiNG ACTIVE FREQUENCIES
Searching the Service Banks
Your scanner contains groups of preset frequencies called sen/ice banks. Each service bank
is associated with a specrfic activrty (see “Sen/ice Banks’ on Page XX]. You can search for
fire/police. air, ham, and marine transmissions even if you do not know the specnic
frequencies that are used in your area. Then you can store the frequencies you found into
the scanner’s channels or monilor memories
Notes
. You can use the scanner’s delay feature while searching the servrce banks, see “Using the
Delay Function" on Page XX.
Page 22
20—314 Owner's Manual Draft
. This procedure uses MAN. FD/F'D. and AIR service banks. If you want to listen to marine
bank, see “Listening to a Marine Bank.”
1. Press BAND. The last selected band name (such as HAM), SFlCH. -o-, frequency and the
group number [it any) appear on the display.
2. To select a dil'lerent band. repeatedly press BAND until the desired band name appears
on the display. After about 2 seoonds, the scanner begins searching rapidly in that band for
an active frequency.
Notes:
. To reverse the search direction at any time, hold down (UP key) or (DN key) tor about 1
second.
. To search the hand up or down in small increments {see “Service Banks“ on Page XX for
trequency steps). repeatedly press and release (UP key) or (DN key).
. To pause the search while receiving a signal press and release (UP Key) or (DN key). To
continue the search, hold down (UF' key) or (DN key).
. To quickly move upward or downward through the frequencies, press and hold down (UP
key) or (DN key). The scanner tunes through the frequencies until you release (UP key) or
(DN key).
3 if needed, select search group with numeral key.
4. When the scanner finds an active frequency, it stops searching and displays the
frequency's number. To store the displayed frequency in the lowest available channel, press
PGM then press ENTER. The channel and frequency flash twice, and the scanner stores
the displayed frequency. The scanner then continues to search for frequencies.
Notes:
. it there is no empty channel, Ch-FULL appears atter PGM pressed. To store more
frequencies. you must clear some channels. See “Clearing a Stored Channel” on Page XX.
To continue searching after Ch-FULL appears, press and hold down (UP key) or (DN key).
. if you entered a frequency that is already stored in another channel, -dUPL- (duplicate) and
the luwescnumbered channel containing the duplicate frequency flash on the display for
about 3 seconds. If you want to store the frequency anyway, press ENTER again. You can
then delete the trequency later. See nClearing a Stored Channel” on Page XX.
Page ‘23
20-314 Owner's Manual Draft
To store the displayed frequency in the channel which you select, press PGM. press channel
number you wish to enter the channel. then press ENTER. The channel and frequency flash
twice, and the scanner stores the displayed frequency. The scanner continues to search for
frequencies.
5. To store the displayed frequency in the monitor memonj, press MON/CL. The monitor
memory number, M and the frequency flash tvirice.
6. To search for another active frequency in the selected band, hold down (UP key) or (DN
key) for about 1 second. To select a different bend and search for another active frequency,
repeat Steps 2-6.
USll‘lg Direct Search
During a direct search. the scanner searches up or down. starting from a frequency you
specify, Follow these steps to use direct search
Note: You can use the scanner’s delay feature while using direct search.
1. Press MAN or PGM, then enter the frequency (including the decimal point) you want to
use as a starting point for the search.
Note: To start from a trequency already stored ln one of your scanner‘s channels, press
MAN or PGM, enterthe desired channel number, then press MAN or PGM again.
Hold down (UP key) or (DN key) for about 1 second to search up or down. —d—, SHCH, and
(U P) 0" (DN) appear on the display.
add illustration.
Notes:
. To reverse the rapid search direction at any time, hold down (UP key) or (DN key) for about
1 second.
. To search up or down the selected band in small increments (in steps 5, 12.5. or 25 kHz),
press and release (UP key) or (DN key).
Page 24
20—314 Owner’s Manual Draft
. To pause the search, press and release (UP key) or (DN key). To continue the search, hold
down (UP key) or (DN key).
.To quickly move upward or downward through the frequencies, press and hold down (UP
key) or (DN key). The scanner tunes through the frequencies until you release (UP key) or
(DN key),
2. When the scanner finds an active frequency, it stops searching and displays the
trequericy‘s number. To store the displayed frequency in the lowest available channel,
press PGM then press ENTER. The channel and frequency flash twice, and the scanner
stores the displayed frequency. The scanner continues to search for frequenCies.
Notes:
. If there ls no empty channel, Ch—FULL appears. To store more frequencies. you must clear
some channels. See “Clearing a Stored Channel“ on Page XX. To oontinue searching after
Ch-FULL appears, press and hold down (UP key) or (DN key).
. if you entered a frequency that is already stored in another channel, 4dUPL- (duplicate) and
the lowest-numbered channel containing the duplicate frequency flash on the display tor
about 3 seconds. If you want to store the frequency anyway, press ENTER again.
To store the displayed frequency in the channel which you select, press PGM, press channel
number you Wish to enter the channel, then press ENTER. The channel and frequency flash
twice, and the scanner stores the displayed frequency. The scanner continues to search for
frequencies.
3. To store the displayed frequency in the monitor memory, press MONiCL. M, the monitor
memory number, and the frequency flash twice
4. To search for another active frequency, hold down (UP key) or (DN key) for about 1
second.
Page 25
207314 Owner's Manual Draft
USING THE MONITOR MEMORY
Listening to the Monitor Memory
To recall a lrequency stored in the monitor memory, press MAN then MONlCL. M, monitor
memory number, and CH flash and the current monitor memory frequency appears on the
display. To select other monitor memories, enter the desired monitor memory’s number
(1—20), then press MONfCl. again. The selected monitor memory‘s trequency appears.
add illustration
Moving a Frequency from the Monitor Memory to a Channel
1. Press PGM, enter the channel number where you want to store the frequency. then press
PG M. PGM and the selected channel number appear on the display.
2. Press MONHCL M, a monitor memory number, and CH flash, and the monitor memory
lrequency appear on the display.
3. Enter the desired monitor memory‘s number (1—20), then press MONICL again. The
selected monitor memory’s trequency appears.
4. Press ENTER, The scanner stores the frequency in the selected channel.
5. To move another monitor memory frequency to the next channel, press PGM and repeat
Steps 2—4.
SCANNING THE STORED CHANNELS
To set the scannerto continuously scan through all channels with stored trequencies. Simply
press SCAN. SCAN and (UP) appear on the display, and the scanner begins to rapidly scan
up until it finds an active frequency
add illustration.
Page 26
90-314 Owner‘s Manual Draft
If the scanner finds an active frequency, it stops and displays that channel and frequency
number, then it automatrcally begins scanning again when the transmission ends on that
frequency
Notes:
. To reverse the scanning direction, press (UP key) or (DN key).
. To set the scanner to remain on the current channel tor 2 seconds alter the transmission
ends, see ‘Using the Delay Function" on Page XX.
. To set the scanner to remain on the current channel, even after the transmission stops,
press MAN at any time during the transmission so MAN appears and SCAN disappears
from the display (see “Monitoring a Stored Channel” on Page XX).
. To lock out channels so the scanner does not stop for a transmissron on those channels,
see ‘Locking out Channels and Frequencies’ on Page XX.
TURNlNG CHANNEL-STORAGE BANKS OFF AND ON
To turn oti a channel-storage bank (1—10), press SCAN to see whloh banks are currently on.
Storage banks are on when they have a bar underneath them and off when no bar appears
underneath them. Press the bank's number key so the bar under the bank's number
disappears
Note: The scanner does not scan any of the channels within the banks you have turned off.
To turn on a channel-storage bank (1—10) press SCAN, and then press the bank’s number
key so a bar appears under the bank's number.
Notes:
.You cannot turn ofi all banks. There must be at least one active bank
. You can manually select any channel in a bank, even it the bank is turned ofl.
. When you turn on the bank while scanning. the scanner moves to the selected bank's
channel and continues scanning.
Page 27
20-314 Owner's Manual Draft
MONITORING A STORED CHANNEL
You can continuously monitor a specific channel without scanning. This ls uselul it you hear
an emergency broadcast on a channel and do not want to miss any details — even though
there might be periods of silence — or it you Simply want to monitor that channel
Follow these steps to manually select a channel.
1. Press MAN.
2. Enter the channel number (1—200).
3. Press MAN again.
CLEARING A STORED CHANNEL
if you no longer want a frequency stored in a channel (and you do not want to replace that
frequency with a difierent one), follow these steps to clear the stored frequency.
1. Press MAN to get cm of the service banks orto slop scanning.
2. To select the desired channel number, use file number keys to enter the! channel number
(1—200), then press MAN.
3. Press PGM. PGM appears
4. Press 0, then press ENTER. The frequency number changes to 000.0000 on the display
to indicate the channel is cleared.
5. To clear another channel, use the number keys to enter that channel number (1—200).
then press PGM again. Or, repeatedly press PGM until the deswed channel number appears.
Then repeat Step 4.
LlSTENING TO THE MARINE BANK
To listen to the marine bank, repeatedly press BAND until MRN appears on the display
Page 28
20-314 Owner’s Manual Draft.
To change the channel manually, press and release (UP key) or (DN key].
Press and hold (UP key) or (DN key) about 2 seconds, the scanner scans through the
marine bank. MAN disappears and SCAN appears on the display. To change the scanning
direction, press (UP key) or (DN key),
To continue changlng the channel manually, press and hold (UP key) or (DN key) about 2
seconds. Press two digits numeric key does move to selected marine channel within marine
manual mode,
LlSTENING TO THE WEATHER BAND
To hear your local forecast and regional weather information, press WX. Your scanner
begins to scan through the weather band.
Your scanner should stop within a few seconds on your local weather broadcast. It the
broadcast is weak, you can press WX again to resume scanning.
Weather
Channel Frequency (MHz)
162.400
162.425
162.450
162.475
l62.500
162.525
162.550
xicnmhmm-fl
WX Alert Feature
This scanner can detect the weather alert tone. The WX alert warns you of serious weather
conditions by sounding an alarm it the weather service broadcasts the weather alert tone,
To listen to the alert tone, press P'Flll‘ALEFlT while you are listening to the WX channel.
ALErt appears on the display. it the scanner detects the weather alert, it sounds an alarm.
Press any key to mute the alarm, To cancel the weather alert operation, press PHI/ALERT
again.
Page 29
20-3l4 Owner’s Manual Draft,
SPECIAL FEATURES
DELAY
Many agencies use a two-way radio system that has a period at several seconds between a
query and a reply. To avoid missing a reply. you can program a 2-second delay into any
channel or frequency. When your scanner stops into any Channel or frequency with a
programmed delay, DLY appears and the scanner continues to monitor that frequency for 2
seconds after the transmission steps before resuming scanning or searching.
You can program a 2-second delay in any oi these ways:
. lithe scanner is scanning and stops on an active channel, quickly press DEiAVl. before it
continues scanning again.
. If the desired channel is not selected, manually select the channel, then press DELAY.
. If the scanner iS searching, press DELAY}.. DLY appears and the scanner automatically
adds a Zsecond delay to every transmission it stops on in that band.
To turn ofl the 2-seoond delay, press DELAYi, while the scanner is monitoring the channel or
irequency. DLY disappears from the display.
LOCKING OUT CHANNELS AND FREQUENCIES
You can increase the eflective scanning or search speed by locking out individual channels
or frequencies that have a continuous transmission. such as a weather channel (See
“National Weather FrequenCies‘ on Page XX) or birdie lieouency (see “Birdie Frequencies"
on Page XX)
Locking Out Channels
To lock out a channel while scanning, press and release uOqu RVW when the scanner
stops on the channel.
To look out a channel manually, select the channel then press and release L/O/L/O RVW
until LID appears on the display.
Page 30
20-314 Owner's Manual Drafi
from a channel, manually select that channel again. then press
To remove the lockoul
the display.
UOILJO RVW so LJO disappears from
Notes:
. Your scanner automatically locks out empty channels.
.You can still manually select locked-oul channels.
Locking Out Frequencies
To lock out a irequency during a service bank, or a directs
scanner locks ou
the scanner stops on the frequency. The
ng. You can lock out frequencres in both direct search and service bank 5
“he lrequency then continues
earches).
searchi
a search. it you try to lock out
many as 50 frequencies during
LockedAOul Frequencies” and
Note: You can lock oul as
(see “Reviewing
more, FLO -FULL appears on the display
“Removing All Lockout Tags From Frequencres”).
Reviewing Locked-Out Frequencies
wn LJO/uO RVW al least 2 seconds
) or (DN key), the scanner displays all
the scanner beeps twice
To review 'the frequencies you locked out, hold do
search. L-r appears. As you press (UP key
during a
arch the highest frequency,
locked out frequencies. When you re
and returns to the lowest locked-out frequency.
Removnng All Locked-Out Tags From Frequencies
earch. See “Usrng Direct Search" on Page XX.
1.815er a service bank or direct s
own UOILJO RVW for about 2 seconds
2. To review the trequencies you locked out. hold d
during the search. L-r appears on the display.
3. Hold down MOMCL lhen HOMO FiVW. FLo ALL-CL appears on the display.
Page 31
20-314 Ow ner’s Manual Draft
4. Press ENTER to clear all the iockout frequencies. The frequency clears and 0000000
appears. if you do not want to clear lockout tags, press MONfCL to continue reviewing all
the lookout frequencies.
Removing All Lockout Tags from Frequencres in All Service Banks
1. Start a service bank or direct search. See “Using Direct Search“ on Page XX.
2. To review the frequencies you locked out, hold down L/OILIO HVW for about 2 seconds
during the search. L-r appears on tho display.
3. Hold down MONICL then press BAND. dEFAULt appears on the display.
4. Press ENTER to clear the lookout frequencies in all the service banks (except weather
bank). If you do not wanl Io clear the lockout tags, press MON/CL to continue revrewing the
lockout frequencres in the sen/ice banks.
USING PRIORITY
Using the priority feature, you can scan through the programmed channels and stilt not miss
an important or interesting call on a specific channel,
To program a priority channel as follows:
Press PGM. then press FRI/ALERT.
Enter the frequency With numeral keys.
Press ENTER.
To turn on the priority feature, press F'FillALEFiT during scanning. PHI appears on the
display. The scanner checks the priority channel every two seconds and stays on the
channel if there is activity. PCH appears on the display whenever the scanner is set to the
priority channel.
To turn off the priority feature, press PFlI. PHI disappears from the display.
Page 32
20-314 Owner’s Manual Draft
It you program WX frequency into the priority channel, the scanner can detect WX alert tone
while priority lealure is on. When the scanner detects WX alert tone, ALErt flashes on the
display. To cancel the alert tone. press any key, and the scanner watch the WX chenneL
USING THE DISPLAY BACKLIGHT
You can turn on the display’s backlight Ior easy viewing in the dark, Press LIGHT to turn on
the display light for 5 seoondst To turn off the light before it automatically turns off, press
LIGHT again.
TURNING THE KEY TONE ON AND OFF
The scanner is preset to sound a tone each lime you press one 0! its keys (except LIGHT)
You can turn the key tone olf or back on
1. If the scanner is on, turn VOLUME counterclockwise until it clicks to turn it off.
2. While you hold down 2 and ENTER, turn on the scanner
8. The display shows OFF IonE or on tonE, then release 2 and ENTER.
USING THE KEY LOCK
Once you program your scanner, you can protect it from aocidental program changes by
turning on the keylock feature When the keypad is locked, the only controls that operate are
SCAN, MANUAL, LIGHT. VOLUME, and SOUELCH.
Note: The keylock does not prevent the scanner Irom scanning channels or monitoring a
single channel, whichever feature you last selected.
To turn on the keylock, hold down (key symbol key) tor about 3 seconds until the scanner
beeps three times and (key symbol) appears on the display To turn it off, hold down (key
symbol key) for about 3 seconds until the scanner beeps three times and (key symbol)
disappears from the display.
Page 33
20314 0“ net’s Manual Draft
CONNECTING A DATA LINK TO THE SCANNER
A daia interface but (no\ supplied) lets you program the scanner with frequencies stored m a
computer program, Contact your meal RadioShack store for more information.
Page 34
20-314 Owner's Manual Draft
A GENERAL SCANNING GUIDE
Fleceplion of the frequencies covered by your scanner is mainly “llne-ol-sight.“ This means
you usually cannot hear slalions that are beyond the horizon.
GUIDE TO FREQUENClES
Nalional Weather Frequencies
151 $50" 161775" 162.400 162.425
162.440“ 162.450 162.475 162.500
162.525 162.550 163.275“
‘Not preprogrammeci in this scanner, bul you can manually program it. (See ‘Storing Known
Frequencies ll'l10 Channels” on Page XX.)
Ham Radio Frequencies
Ham radio operators often transmil emergency lnlormatlon when other means of
communication break down. The following chart shows the frequencies this scanner
receives ihat ham radio operators normally use:
Wavelength Frequency (MHZ)
10 meters 29130029700
6 meters some-54.000
2 meters 144.0004 48.000
70 cm 420.000-450.000
Nole: Your scanner cannot receive AM lransmissrons on 1hese bands.
Page 35
20-314 Owner's Manual Draft
Birdie Frequencies
Every scanner has birdie frequencies — signats created inside the scanners receiver, which
might interfere with broadcasts on the same frequencies. If you program one of these
frequenCies. you hear only noise on that trequency. lt the interference is not severe, you
might be able to turn SOUELCH clockwise lo cut out the birdie.
To find the birdies in your scanner:
Disconnect the antenna and move it away from the receiver. Make sure that no other
nearby radio or TV sets are turned on near the scanner.
. Search in each frequency band from its lowest lrequency to the highest. Occasionally, the
searching will stop as it it had iound a signal, often without any sound. That is a birdie.
. Make a list at all the birdies in your particular scanner for future relerenoe.
The birdie frequencies to watch for on the PRO-79 are:
birdie frequencies will add
GUIDE TO THE ACTION BANDS
United States Broadcasl Bands
lo the United States, there are several broadcast bands. The standard AM and FM bands
are probably the most well known. There are also four television audio broadcast bands —
the lower three transmit on the VHF band and the fourth transmits on the UHF band.
Page 36
20314 Owner's Manual Draft
Typical Band Usage
HF Band (SOD—30.0 MHZ)
10-Meter Amateur 29 00-2970 MHz
High Flange 2970-2930 MHz
VHF Band (51000—30000 MHZ)
Low Range GOOD-50.00 MHz
S-Meter Amateur 5000-5400 MHz
U.S. Government 13700-14400 MHz
EvMeter Amateur 144.00—14BDU MHz
High Range 14300-17100 MHz
UHF Band (300.00 MHZ4.O GHz)
Military Aircraft 330.00-384400 MHz
U.S, Government 40500-42000 MHZ
7D-Centimeter Amateur 42000-45000 MHz
Low Range 45000-47000 MHZ
FM-TV Audio Broadcast,
Wide Band 47030—51200 MHz
Primary Usage
As a general rule. most of the radio activity IS concentraied on the following frequencies:
VHF Band
Acnvrties Frequencies (MHz)
Government, Police. and Fire 153.785—155‘980
Emergency Servrces 158.730—159460
Railroad 160.000—161 900
Page 37
20-314 Owner's Manual Draft
UHF Band
Activities Frequencies (MHZ)
Land-Mobile “Paired' Frequencies 450,000—470000
Base Station 4510125454950
Mobile Units 456.025—459 950
Flelay Repeater Units 460.025—464975
Remote Control Stations 465.025—469975
Note: Remote control stations and mobile units operate at 5 MHz higher than their
associated base stations and relay repeater units.
Specified Intervals
Frequencies in different bands are accessible only at spemfic intervals For example:
Frequency Range(s) Specilied Interval
29—54 MHZ and 137-174 MHZ 5.0 kHz Steps
380—512 MHz 12.5 kHz Steps
Note in service bank search, the frequency interval is not the same as specified above See
“Sen/ice Banks“ on Page XX.
BAN D ALLOCATION
To help decide which frequency ranges to scan, use the lollowmg listing of the typical
sen/ices that use the lrequencies your scanner receives. These frequencies are subject to
change and might vary from area to area. Fora more complete listing, reter to Police Call,
available at your local FiadoShack store.
Abbrewations Services
AIR Aircraft
BIFC Boise (ID) lnteragency Fire Cache
BUS Business
CAP CiVil Air Patrol
CCA Common Carrier
Page 38
CSB
CTSB
FIRE
HAM
GOVT
GM R
GTR
lND
MAR
MARl
MARS
MED
MIL
MOV
NEW
NEWS
OlL
POL
PUB
PSB
PTR
ROAD
RTV
TAXI
TELB
TE LC
TE LM
TOW
TRAN
TSB
20-314 Owner's Manual Draft
Conventional Systems
ConventionaIlTrunked Systems
Fire Department
Amateur (Harri) Radio
Federal Government
General Mobile Radio
General Trunked
Industrial Services
(Manufacturing, Construction, Farming, Forest Products)
Military Amateur Radio
Maritime limited Coast
(Coast Guard, Marine Telephone, Shipboard Radio,
Private Stations]
Military Alfiiiate Radio Systems
Emergencyjlvledical Services
U 5. Military
Motion Picture/Video Industry
New Mobile Narrow
Relay Press {Newspaper Reporters)
Oil/Petroleum Industry
Police Department
"Public Services
(Public Safety, Local Govt, Forestry Conservation)
Pu bilc Salety
Private Trunked
Road & Highway Maintenance
Radio/TV Remote Broadcast Pickup
Taxi Services
Mobile Telephone
[AircraIL Radio Common Carrier, Landline Companies)
Cordless Phones
Telephone Maintenance
Tow Trucks
Transportation Services
(Trucks, Tow Trucks. Buses. Railroad, Other)
Trunked Systems
Page 59
20-314 Owner's Manual Draft
TVn FM-TV Audio Broadcast
USXX Government Classified
UTI L Power & Water Utilities
WTHR Wealher
High Frequency (HF) Hi — (3 MHz—30 MHz)
10-Merer Amaleur Band - (EBB-29.7 MHZ)
29 COO-29.700 HAM
Very High Frequency (VHF) - (30 MHz—300 MHz)
Low Band — (297—50 MHz 7 in 5 kHz steps)
29700-29790 IND
29800-30550 GOVT, MIL
30550-31380 IND, PUB
32000-32990 GOVT, MIL
33020-33380 BUS, IND, PUB
34010434390 GOVT, MIL
35.020—35380 BUS, PUB, IND. TELM
36000-36230 GOVT, MIL
36.250 Oil Spill Clean-Up
36270-36990 GOVT, MIL
3102037380 PUB, IND
3800039000 GOVT, MIL
3902039980 PUB
40.000—42000 GOVT, MIL, MARI
42020—42340 POL
42960—43180 IND
43220-43680 TELM. IND, PUB
43700-44500 TRAN
4452046580 POL, PUB
46500-46990 GOVT, TELC
41020-41400 PUB
47.420 American Red Cross
4144049580 IND, PUB
Page 40
207314 Owner's Manual Draft
49151049990 MIL, TELC
e—Meter Amateur Band ~ [50754 MHz)
5000-5400 HAM
U.S. Guvemmem Band (138—144 MHz)
137 GOO-144.000 GOVT, MIL
2—Meter Amateur Band — (1447148 MHz)
144.000-1 48.000 HAM
VH F-HI Band (143—174 MHZ}
148.050-1 50.345 CAP. MAR, MIL
1507754511790 M ED
150.81 5-1 50.965 TOW
150.980 Oil SpiII Clean-Up
150.995-151 130 ROAD
151 11 45-1 51 475 POL
151490451955 IND, BUS
151,985 TELM
152.0075 MED
152030452240 TELB
152270452465 IND, TAXI
152.480 BUS
152510452840 TELB
152870453020 IND, MOV
1521035453725 IND, OIL, UTIL
153.740—154445 PUB, FIRE
154.490-154570 IN D, BUS
154.585 OII SpiII Clean-Up
154.6004 54.625 BUS
154.655-156240 MED, ROAD, POL, PUB
156.255 OIL
156.275-157.425 MARI
157.450 MED
157.470-157.515 TOW
Page 41
20- 314 Owner’s Manual Draft
157.530-1 57.725 IND, TAXI
157.740 BUS
157.770-158.100 TELB
158130458460 BUS, IND, OIL. TELM, UTIL
158 490-158.700 TELB
158.730~159.465 POL. PUB, ROAD
159 480 OIL
159495461565 TRAN
161 580 OlL
161600462000 MART. HTV
1620125462135 GOVT. MIL, USXX
152.400-162.550 WTHR
162.5625~162.6375 GOVT, MIL. USXX
162. 8625 M E D
162.6875-1 63.225 GOVT, MIL, USXX
163.250 MED
163275466225 GOVT. MIL, USXX
166.250 GOVT, RTV. FIRE
188.275-1 69.400 GOVT. EIFC
169.445 Wiralafis Mics
169.500 GOVT
169.505 Wireless chs
169554693875 GOVT. MIL, USXX
170.000 BIFC
170025470150 GOVT, RTV, FIRE
170.175-170225 GOVT
170245470305 Wire‘ess M4CS
170.350-1 70.400 GOVT, MIL
170.425-1 70.450 BIFC
170.475 PUB
1704875473175 GOVT, PUB, Wireless Mics
173,225-1 73.375 MOV, N EWS. UTIL
173.3875-1735375 MIL
173.5625-1735875 MIL. Medical/Crash Crews
173604739875 GOVT
Page 42
20314 Owner's Manual Draft
Ultra ngh Frequency [UHF] [300 MHz—3 GHZ)
Military Aircraft Band (3191—3839 MHZ}
380000883300
Coast Guard
U.S. Government Band (406—450 MHz)
405125419375
GOVT. USXX
70-cm Amateur Band (420—450 MHZ]
420.000—450.000
Low Band (450-470 MHZ)
450050450325
451025452025
4520375453000
453.0125-453.9875
454.000
454.025-454.975
455050455925
457525457600
458025455175
460.0125-4BD.6875
460650462175
4621875462450
4624625462525
462550462725
462750462925
462.8375-463.1875
463200467925
HAM
RTV
lND, OIL, TELM, UTlL
lND, TAXI, THAN, TOW, NEWS
PUB
Oll.
TELB
RTV
BUS
MED
FIRE, POL, PUB
BUS
BUS, lND
IND, OlL, TELM. UTIL
GMR
BUS
MED
BUS
FM-TV Audio Broadcast, UHF Wide Band (470—512 MHZ)
(Channels 14 thmugh 20 in 6 MHz steps)
475.750
481.750
487.750
493.750
Channel 14
Channel 15
Channel 16
Channel 17
Page 43
20-314 Owner’s Manual Draft
499.750 Channel 18
505.750 Channel 19
511.750 Channel 20
Note: Some cities use the 470—512 MHZ band [or land/mobile service
AVOIDlNG IMAGE FREQUENCIES
You might discover one of your regular stations on another frequency that is not listed. ll
might be what is known as an image frequency. For example. you might lind a sen/toe that
regularly uses a frequency 01453275 also on 474.675.
To see if it 15 an image, do a little math.
Note the new lrequency. 474 675
Double the intermediate frequency of 10.? MHz
(21.400)
and subtract it from the new frequency. 41.400
if the answer is the regular frequency, 453.275
then you have tuned to an 1mage.
Occasionally, you might get interference on a weak or distant channel from a strong
broadcast 21.4 MHz above or below the tuned frequency. This is rare, and the image signal
is usually cleared whenever there lS a broadcast on the actual frequency.
Page 44
20314 Owner’s Manual Draft
FREOU EN CV CONVERSION
The tuning beation of a station can be expressed in 1requency {kHz or MHz) or in
wavelength (meters). The following inlormation can help you make the necessary
conversions
1 MHz (rmllion) = 1000 kHz (lhousand)
To convert MHz to kHz, multrply 1he number of MHz by 1,000:
30.62 MHZ X 1000 - 30,620 kHz
To conven from kHz to MHz, divide the number of kHz by 1000.
1271800 kHzI1000 2127.8 MHZ
To conven MHz to melers, diwde 300 by the number of MHz‘
300 I 50 MHz = 6 meters
Page 45
20-314 Owner's Manual Draft
TROUBIESHOOTING
It your scanner is not working as it should, these suggestions might help you eliminate the
problem. It the scanner still does not operate properly, take it to your local HadioShack store
tor assistance.
Scanner is totally The batteries are dead, Replace the batteries with fresh
inoperative. ones, cr recharge the rechargeable
batteries.
The optional AC or DC Be sure the adapter is fully inserted
power adapter is not into the PWFi jack.
connected.
Poor or no reception. Improperly connected Be sure the antenna is properly
antenna. connected.
Programming frequencies Avoid programming frequencies
are the same as birdie listed under “Birdie Frequencies" on
frequencies. Page XX or only select them
manually.
Error appears on the Programming error Reprograrn the frequency correctly.
display.
Keys do not work or Undetermined error. Turn the scanner oil then on again,
display changes. or reset the scanner (see
“Resetting/Initializing the Scanner'
on Page XX).
Page 46
20-314 Owner’s Manual Draft
Scanner is on but will not SQUELCH is not Adjust SQU ELCH clockwise (see
scan. correctly adiusted. “Turning on the Scanner and
Setting Squelch“ on Page XX).
In the scan mode, the Birdies Avoid programming trequencies
scanner locks on listed under "Birdie Frequencies“
trequenCies that have on Page XX or only listen to them
an unclear transmission. manually.
RESETHNG/INITIALlZWG THE SCANNER
it the scanner’s display locks up or does not work properly alter you connect a power source,
you might need to reset or initialize the scanner.
Important: If you have problems, first to; to reset the scanner {see “Resetting the Scanner“).
If that does not work. you can initialize the scanner (see “Initializing the Scanner" on Page
XX); however, this clears all information stored in your scanner’s memory.
Ftesetting the Scanner
1 Turn oft the scanner, then turn it on again.
2. Insert a pointed object, such as a straightened paper clip, into the reset opening on the
Side 01 the scanner (as shown) and gently press then release the reset button inside the
opening.
add illustration.
Note: It the scanner still does not work properly. you might need to initialize the scanner (see
“initializing the Scanner”)
Page 47
20-314 Owner’s Manual Draft
lniliallzing me Scanner
Important Thls procedure clears all information you stored in the scanners memory
initlallze the scanner only when you are sure the scanner is not working properly.
1. Turn off the scanner, then turn it on again
2. Hold down MON/CL.
3, While holdlng down MON/CL, insen a pomted object, such as a stralghtened paper cup,
into the reset opening on the side of the scanner and gently press then release the reset
button lnside the openlng. The display should clear
All When the display reappears, release MONlCL.
Note: You must release the reset button before releasing MON/Cu otherWlse the memory
rnlght not clear.
Page 48
20-314 Ow net’s Manual Draft
CARE AND MAlNTENAN CE
Your RadioShack PRO-79 EDD-Channel Portable Scanner is an example of superior design
and crattsmanship. Thetollowing suggestions will help you care tor your PRO-79 so you can
enjoy it for years.
Keep the PRO-79 dry. it it gets wet, wipe it dry immediately, Liquids might contain minerals
that can corrode the electronic circuits.
Use and store the PRO-79 only in normal temperature environments. Temperature extremes
can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.
Keep the PRO-79 away trom dust and dirt, which can cause premature wear ot pans.
Handle the PRO-79 gently and carefully. Dropping it can damage circuit boards and cases
and can cause the PRO-79 to work improperly.
Use only fresh batteries ot the required size and recommended type. Batteries can leak
chemicals that damage your PRO-79’s electronic parts.
Wipe the PRO-79 With a damp cloth occasionally to keep rt looking new. Do not use harsh
chemicals, cleaning solvents, or strong detergents to clean the PRO-79.
Modifying or tampering With the scanner’s internal components can cause a malfunction and
might invalidate its warranty and void your FCC authorization to operate it. It your scanner is
not performing as it should. take it to your local FtadioShack store for assistance.
Page 49
SPECFICAflONS
Frequency Coverage:
Ham
VHF Lo
Ham
Air
Govemmem
Ham
VHF H)
HamlGovernmenI
UHF Lo
UHF Hi (T)
mama-B of Operation
Senswtivity (20 dB SFN)‘.
29-54 MHZ
108-1 35.9875 MHZ
137-174 MHZ
3807512 MHZ
Selectivtty',
+f-10 kHz
+I-18 kHz
Spurlous Reflecnon
Scanning Rate
Search Rate
Delay Tvme
mtermediate Frequencies (1F):
15)
2nd
H: |mefierence Ratio (10.7 MHz)
Squelch Sensitlv‘rty:
Threshold
Trght (FM)
Tight (AM)
20314 OWner's Manual Draft
29-30 MHz (5.0 kHz Slaps)
30-50 MHz (50 kHz Steps)
5054 MHz (50 kHz Steps)
1084369875 MHz (125 kHz Steps)
137-144 MHz {5 kHz Steps)
144-148 MHz (5 kHz Steps)
148—174 MHz (5 kHz Steps)
3804150 MHz (125 kHz Slaps)
450-470 MHz (12.5 kHz Steps)
4707512 MHZ (12.5 kHz Steps)
20K) Channeis and 20 Monitor Memories
0 5 w
1.0 uV
0.5 uV
0.7 [N
-6 dB
-50 (“3
so (118 (FM al154 MHZ)
Up to 25 Channels/Second
Up is 50 SlepsfSecond
2 Seconds
10.7'MHZ
455 kHz
70 dB a! 150 MHZ
Less than 045 uV
(5mm) 25 dB
(3mm 20 dB
Page 50
20-314 Owner's Manual Draft
Antenna impedance 50 Ohms
Audio Output Power (10°10 THD] 180 mW Nominal
Built-in Speaker 1 3B inch {36 mm) 8-0hm, Dynamic Type
Power Requirements +6 V DC, 4 AA Batteries
AC Adapter (Cal. No. 273-1767]
DC Adapler (Cat No. XXX-XXXX}
Current Drain (Squeiched) 50 mA
Operating Temperature +14F to *140F
(-1 DC 10 +60C)
Dimensions (HWD) 5 11116 x 2 1/2 x1 Ell! inches
(145 x 63 x 34 mm)
Weight Approx. 7.1 oz.
(200 9) without Antenna
Supplied Accessories Antenna,
Battery Holder
Rechargeable Battery Holder
Spemlicalions are typical; individual units might vary. Spemfications are subject 10 change
and improvement without notice.
Page 51

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 1999:10:18 09:42:06-05:00
Create Date                     : 1999:10:18 09:34:30-05:00
Creator                         : Acrobat 4.0 Scan Plug-in for Windows
Producer                        : Acrobat 4.0 Scan Plug-in for Windows
Page Count                      : 51
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AAO2000314

Navigation menu