Radio Shack 4301107C 900 MHz Cordless Telephone User Manual Draft Copy of Owners Manual

RadioShack Corporation 900 MHz Cordless Telephone Draft Copy of Owners Manual

Draft Copy of Owners Manual

Download: Radio Shack 4301107C 900 MHz Cordless Telephone User Manual Draft Copy of Owners Manual
Mirror Download [FCC.gov]Radio Shack 4301107C 900 MHz Cordless Telephone User Manual Draft Copy of Owners Manual
Document ID92695
Application IDBkhtfAmz467NGvuIFRx05A==
Document DescriptionDraft Copy of Owners Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize39.97kB (499627 bits)
Date Submitted2000-03-22 00:00:00
Date Available2000-04-06 00:00:00
Creation Date2000-03-08 12:51:40
Producing SoftwarePhotoshop PDF Plug-in 1.0
Document Lastmod2000-03-08 12:52:09
Document TitleDraft Copy of Owners Manual
Document CreatorPhotoshop PDF Plug-in 1.0

User Manual
DRAFT COPY OF THE INSTRUCTION MANUAL
UC283—15.duc I1
Introduction
Your 900 MHz cordless phones is designed and engineered to exacting
standards for reliability, long life, and outstanding performance.
Features
900 MHz Extended Range Technology
30 Channel Autoscan
9—Number Memory Dialing
3 One—Touch Priority Keys
Desk or Wall Mountable
Tone/Pulse Dialing
Handset Volume Control
32 Digit Redial
Page/Find
AutoTalk
AutoStandby
7 Hours Talk Time
Hearing Aid Compatible
NOTICE:
Modifying or tampering with internal components of your cordless phone can
cause a malfunction and might invalidate its warranty and void your FCC
authorization to operate it. If your phone is not performing as it should,
take, it to your local store for assistance. If the trouble is affecting the
telephone line, the phone company can ask you to disconnect your phone until
you have resolved the problem.
Your 900 MHz cordless phone includes AutoTaIk and AutoStandby. AutoTalk
allows you to answer a call by just removing the handset from the base
so you dont have to waste time pushing buttons or flipping switches.
UC283-15. doc 14
AutoStandby allows you to hang up by simply returning the handset to the
base.
The UltraClear Plus true compander circuitry virtually eliminates
background noise. This innovative technology, together with 40 different
channels, provides you with the best possible reception during all your
conversations.
To protect you against misbilled calls which might result from your
phone being activated by other equipment, your phone has Random Code
digital security which automatically selects one of over 65,000 digital
security codes for the handset and base. Also, the AutoSecure feature
electronically locks your phone when the handset is in the base.
To get the most from your phone, please read this owners manual
thoroughly. Also, be sure to complete the product registration form and
mail it in.
Included with Your Phone
This Owners Manual
Other Printed Material
Precautions and Important Safety Instructions
Controls and Functions
.talk — answers or places calls
.*/tone — switches to tone dialing in pulse dial mode
.redial - redials the last number
.pause - adds a timed pause in a memory dialing sequence
talk/batt — LED indicates when phone is in use or the battery is low
.f|ash — accesses call waiting (if available)
.mem — enters or recalls numbers in memory
.volume — sets both the ringer and earpiece volumes
.chan — selects another channel for clearer reception
woowomawN—a
UC283—15. doc 15
10.mi, m2, m3 - accesses stored numbers in memory locations I, 2, and 3
for one—touch dialing
ll.handset retainer - holds handset in base for wall mounting.
12.status LED — indicates the phone is in use or the handset is charging
l3.page/find - locates the handset
lnstal lation
Charging the Battery Pack
The rechargeable Nickel—Cadmium battery pack must be fully charged
before using your phone for the first time. Before plugging the phone
line into your new phone. you must charge the battery for approximately
15—20 hours without interruption.
l.Remove the handset battery cover.
2.Plug the batterys cable into the handset and place the battery pack
inside the battery compartment.
3.Replace the battery cover.
Charging the Handset
Place the handset on the base to charge. (The handset can charge in
either the face—up or face-down position.)
Low Battery Indicator
When the battery pack in the handset is low and needs to be charged, the
batt LED flashes every 3 seconds. it this occurs while you are on the
phone, you will hear an alert tone. Complete your call as quickly as
possible, and return the handset to the base for charging.
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all battery contacts
on the handset and base about once a month. Use a pencil eraser or other
contact cleaner. Do not use any liquids or solvents.
U0283—15.doc 16
Selecting a Location
Before choosing a location for your new phone, read the Installation
Considerations included in the Precautions and Important Safety
Instructions brochure. Note: Raise the antenna on the base to get best
communication range.
Setting the Dial Mode Switch
Desk or Tabletop Installation
l.Plug the AC adapter cord into the W on input jack on the base.
2.Wrap the AC adapter cord inside the molded strain-relief.
3.Plug one end of the long telephone cord into the TEL LINE jack on the
base.
4.Place the telephone cord into the right molded channel cord holder.
5.Plug the other end of the telephone cord into the telephone wall jack.
(Remember, the phone must be fully charged before you can use it.)
6.Plug the AC adapter into a standard 120V AC wall outlet that is not
controlled by a wall switch.
7.Raise the antenna on the base.
Wall Installation
Setting the Handset Retainer for Wall Mounting
l.Remove the handset retainer on the base by sliding it upward.
2.Flip the retainer over so the tab is facing up.
3.Slide the retainer back onto the base.
Mounting on a Standard Wall Plate
The phone is designed to be mounted on a standard ANT or GTE wall plate.
l.PIug the AC adapter into the base.
[Place the AC adapter cord inside the left molded channel cord holder.
3.Plug a short telephone cord into the TEL LINE jack on the base.
4.Place the telephone cord into the right molded channel cord holder and
plug the other end of the cord into the wall jack. (Remember, the phone
UCZBfl—IS. doc 17
must be fully charged before you can use it.)
5.PIace the base on the two posts of the wall plate and slide downward
to secure.
6.Plug the AC adapter into a standard 120V AC wall outlet that is not
controlled by a wall switch.
7.Raise the antenna on the base to get best communication range.
Mounting Directly on a lllall
If you do not have a standard wall plate, you can mount the phone
directly on a wall. Before mounting your cordless telephone, consider
the following:
Select a location away from electrical cables, pipes, or other items
behind the mounting location that could cause a hazard when inserting
screws into the wall.
Make sure the wall material is capable of supporting the weight of the
base and handset; otherwise, damage to the unit could result.
Use 310 screws with anchoring devices suitable for the wall material
where the base will he placed.
l.|nsert the screws, with their appropriate anchoring devices, 35/16
inches apart. Allow 3/15 of an inch between the wall and screw heads for
mounting the phone.
2.Plug the AC adapter into the base.
3.Place the AC adapter cord inside the left molded channel cord holder.
4.Plug one end of the long telephone cord into the TEL LINE jack on the
base.
5.Place the telephone cord into the right molded channel cord holder.
6.Place the base on the screws and push down until its firmly seated.
7.Plug the other end of the telephone line into the telephone wall jack.
(Remember, the phone must be fully charged before you can use it.)
8.Plug the AC adapter into a standard 120V AC wall outlet that is not
controlled by a wall switch.
9.Raise the antenna on the base to get best communication range.
UC283-15. doc 18
Setting Up Your Phone
Raising the Antenna
Before using your phone, be sure to raise its antenna to the vertical
position.
Adjusting Ringer/Volume Controls
Ringer Tone and Volume
i.WhiIe the phone is not in use, press volume .
2.The phone has two ringer tones, each with two volume levels. Press
volume again until you hear the ringer tone and volume level you want.
Setting the Handset Earpiece Volume
l.llhile you are on a call, press volume.
2.The phone has two receiver volume levels, one soft and one loud. Press
volume again until you hear the volume level you want.
3.Plug the AC adapter into a standard lZOVAC wall outlet that is not
controlled by a wall switch.
4.Place the handset upright in the charging cradles (The handset can be
placed in the charger with the keypad facing either the front or back of
the charging cradle.)The charge LED lights while the unit is charging.
Using Your Phone
Making and Receiving Calls
Storing a Number in Memory
Your 900 MHz cordless phone has 9 memory locations for storing important
telephone numbers.
I.Remove the handset from the base and press mem. The talk LED flashes
and you hear a beep‘
2.Enter the phone number you want to store (up to 16 digits).
3.Press mem and enter a number (1—9) on the keypad for the memory
location you want to use.
You hear a long been and the talk LED goes out indicating the number has
been stored successfully.
U0283—15.d0c 19
If you select any keys other than 1-9, the handset will beep rapidly and
no number will be stored.
Entering a Pause in Memory Dialing
If you would like to use a phone number stored in memory to access voice
mail, for example, you can store a pause in the phone number sequence.
To use this function, follow steps 1 and 2 in Storing a Number in Memory,
then press the pause button on the handset to place a pause in the phone
number sequence.
Follow the remaining steps in the Storing a Number in Memory section to
complete the operation.
Storing Mixed Tone/Pulse Numbers
If your phone is set up for pulse dialing, you can store a mixed mode
number (up to 16 digits) to easily access long distance services.
l.Remove the handset from the base and press mem. The talk LED flashes
and you hear a beep.
2.Enter the number to be dialed in pulse mode.
3.Press the t/tone button on the handset. The */tone button counts as
one digit and enters a pause.
4.Enter the number(s) to be dialed in tone mode.
5.Press mem and a number (1—9) on the keypad for the memory location you
wish to use. You hear a long beep and the talk LED goes out.
Dialing a Stored Number
To dial a phone number stored in memory, press talk, then press mem and
the memory location (0—9). Your phone will dial the stored number.
One—Touch Dialing
Your phone is equipped with three One—Touch Priority keys for instant
dialing (ml, m2, and m3). You cannot store phone numbers directly into
ml, m2, and mi. They are only used to dial phone numbers stored into
memory locations 1, 2, and 3 on the keypad.
UCZ83—15. doc 20
l.To instantly dial phone numbers stored in memory locations 1, 2, or 3,
simply press ml, m2, or me (There is no need to press talk, the phone
will automatically dial.)
2. If no phone number was stored in memory locations I, 2, or 3 on the
keypad, pressing ml, m2, or m3 will do nothing.
Chain Dialing
After dialing a number you may be requested to enter a special access
code, for example, when performing a banking transaction.
l.Store the access code into one of the memory locations(l—9)t
2.Dial the main number.
3.Press mem and the memory location of the access code at the
appropriate time.
Erasing a Stored Number
l.Remove the handset from the base.
Z‘Press mem twice.
3.Press the memory location number (1—9) you want to clear. You hear a
long beep confirming that you have erased the number.
Replacing a Stored Number
Remember, your phone has 9 memory locations, represented by the numbers
1—9 on the keypad. If you store a phone number in one of these locations,
then attempt to store a different number in the same location later, the
new number will replace the previous one.
Selecting a Different Channel
If you encounter interference while using your phone, you can manually
change the phones channel for clear operation‘ Interference can come
from appliances or other phones in your home‘ This function works only
when the phone is in use.
The chan button on the handset allows you to choose between 40 factory
set channels. During the course of a conversation, if you hear static or
noise which makes it difficult to hear, press chan. The talk LED flashes,
UCZBS-l 5. doc 21
indicating the phone is changing to another channel.
Using the Flash Button
Use flash for accessing services such as call waiting. If you receive a
call during your conversation, press the flash button on the handset.
Press flash again to return to the previous call.
Using the Page/Find Feature
The Page/Find feature sends a signal from the base to the handset
causing it to been. This is useful for locating the handset when it is
away from the base. To use this feature, press page/find on the base.
The handset beeps for 60 seconds. (Press and hold the page/find button
to get a continuous beep.)
On the handset press talk to end the page. Press talk again if you do
not wish to make a call.
Traveling Out of Range
When you begin to move too far from the base, you will first hear a
clicking sound. As you travel further out of range, the voice
transmission will begin to break up. If you pass the range limits of the
base, your call will terminate.
U0283-15. doc 22

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 2000:03:08 12:52:09
Creator                         : Photoshop PDF Plug-in 1.0
Producer                        : Photoshop PDF Plug-in 1.0
Create Date                     : 2000:03:08 12:51:40
Page Count                      : 10
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AAO4301107C

Navigation menu