Radio Shack 6004319 Fire Engine with Bump User Manual
RadioShack Corporation Fire Engine with Bump Users Manual
Users Manual
® RadioShack. CORPORATION ProduclEniuallooandBlmpllumlilmberly card Radlo COHTTOI WOMEN! its“ I“ MM,TXTI1IIZ~M I I I one“... Fire Engine wrth Bump. “II".WMMW INSTALLING BATTERIES WARNING: Dispose of old batteries promptly and properly. Do not burn or bury\them. CAUTIUNS: - Use only fresh batteries ofthe required size and recommended type. - if you do not plan to use the Fire Engine fora week or more, remove the bananas from both the transmitter and the Fire Engine. Batteries can leak chemicals that can destroy electronic parts. CONTROLLER BATTERY INSTALLATION Use a Phillips head screw driver to remove the battery compartment cover located on the back of the controller. lnserlt ‘9V.' alkaline battery In the correct position as marked In compartment Replace cover and screw. , FIRE ENGINE INSTALLATION 1. Follow all operating instructions and precautions to charge your ‘6V' rechargeable battery pack. Note: most rechargeable batteries need charging when newly purchased. 2. Insert fully charged battery pack Into battery compartment the (+) and (-) ends match. Use a coin or Philip screw to turn the battery lock and secure the battery in place. RADIO CONTROL DRIVING 1. Slide ONIOFFto ON underneath the fire Engine. 2. Fully extend the antenna on the transmitter and slide OFF/ON on the transmitter to ON. The indicator on the transmitter lights. 3. Use the transmitters control levers to move and swer the Fire Engine. 4. When you finish driving the Fire Engine, slide OFF/ON on the fire Engine and the transmitter to OFF FIRE ENGINE FONOTION CONTROLS Install fully charged rechargeable batteries Into the Fire Engine battery compartment and transmitter in the correct position as Indicated. install transmitter antenna as indicated. Move power switches located underneath the Fire Engine and front of the transmitter to the "on“ positions. Fully extend transmitter antenna Place Fire Engine on a flat surface. . To drive the Fire Engine. move “selector switch" to the left to select FlreEnglne operations. ' Emergency lights will flash with siren sound when Fire Engine ls moving. - To drive forward, move ‘ioystick A' upward. 0 To drive In reverse, move “joystick A‘ downward. , - To turn right, move 'loysttck A" upward and ‘joystlck B' to the right. - To reverse left, move ‘loystlck A' downward and "joystick B' tothe left . To reverse right move 'ioystfck A" downward and “ioystick B” to the right. - To operate the ladder, move “selector switch" to the right to select ladder operations. NOTE this equipment has been tested and found to comply wllh . To extend and raise ladder, move “joystick A' no upward \' the limits for a Class B digital device, pursuant to Part 15 ofthe FCC ~ - g Rules. These limits are designed to provide reasonable protection . To met and lower ladder. move Joystick A_downward. against harmful mmnce In a msldemial Installation This - To rotate ladder to the right, move loysttck B to the right. . . . . equipment generates, uses and can radiate radio frequency energy ' T° mm “mm "1° hit. mm Wm" B I” n“ M" and it not Installed and used in accordance inmate instructions - To squirt water, push the water button locate on the controller.\ ' ' Cautions : Do not point water pump at the eyes. may ms” "m"! m “In“ commit ' This device complies with Part 15 oithe Fcc Rules. Operation is subject to the following two conditions: (1) This device may not cause hamful interference, and (2) This device must accept any Interference received. Including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment However, titers Is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful Interference to radio orfelevlslon reception, which can be determined by fuming the equipment off and on, the user is encouragedto try to correctthe Interference by one or more of the following measures: Reorlent or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from thatto which the receiver is needed. Consult the dealer or an experienced radlofl'v technician for help. .,
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2002:04:30 17:49:55+08:00 Create Date : 2002:04:30 17:49:39+08:00 Creator : Acrobat 4.0 Scan Plug-in for Windows Producer : Acrobat 4.0 Scan Plug-in for Windows Page Count : 1EXIF Metadata provided by EXIF.tools