Radio Shack 6301026R User Manual
RadioShack Corporation
USER MANUAL
63-1026.fm 1 Tue Sep 22 [5:59:26 1998 Cat. No. 63-1026 OWNER’S MANUAL Please read before using this equipment. lhdoor/outdobrg. } J flag;Thermometer RadioShack@ FCC ID: AAO6301026R 6? FCC ID: AAO6301026R I? 63-1026.fm 2 Tue Sep 22 15:59:261998 lNTRODUCTlON Your RadioShack Indoor/Outdoor Thermometer with Wire- less Remote Sensor is a complete system that lets you mon~ itor the temperature indoors and out! You can hang the main unit indoors on a wall or use its built-in stand for easy view- ing on a table or desktop. You can place the supplied remote sensor outdoors or in another room to monitor the tempera ture at that location. ' nets. Altogether you cark'lmonitor the temperature at four dif- ferent locations! fit The system’s features inlalude: Dual Line Temperature Display —— the top half of the main unit’s display shows the temperature at the remote sensor (outdoors, for example) and the bottom half shows the tem- perature at the main unit’s location. Temperature Alarm —- lets you set the main unit to sound an alarm each time a set high or low temperature is reached at a remote sensor's location. '© 1998 Tandy Corporation. All Rights Reserved. . RadloShack is a registered trademark used by Tandy Corporation. 69 ' 51x‘kti Lassa-do“ . FCC ID: AA06301026R ‘ 63-1026.t‘m 3 Tue Sep 22 15:59:26 1998 Three Remote Sensor Channels — let you use up to two additional remote sensors (not supplied) with the system ‘ and monitor the temperature at up to four different locations. “J. Low Battery indicator — lets you know when the main unit's or any remote sensor’s battery power is low. v K'):5"C<; -<,¢-v.:':_-_-\. . r. . _~ kn“ FCC ID: AAO6301026R 63-[026.fm 4 Tue Sep 22 [5:59:26 1998 TABLE OF CONTENif'S Installing Batteries ............ ' ............................................... 5 In the Remote Sensor .'..i;f .............................................. 6 . In the Main Unit ............ ”. .............................................. 7 When to Replace the Batteries .................................... 7 Mounting ........................................................................... 8 Selecting a Location .................................................... 8 Main Unit ..................................................................... 9 Remote Sensor .......................................................... 10 Operation ................................................................. 12 Setting/Selecting the Display Channel ....................... 13 Changing the Degree Format .................................... 14 Reading the Temperature Trend Display ................... 15 Reading the Kinetic Wave Display ............................. 15 Checking the Maximum/Minimum Temperatures ....... 16 Using the Temperature Alarm .................................... 17 Troubleshooting ............................................................. 18 Manually Searching for a Signal ................................ 18 Resetting the System ................................................ 19 Care and Maintenance ................................................... 20 Specifications ................................................. - 22 <9 You need four AA batteries (not supplied) to power your thermometer system g;— two each for the main unit and re- mote sensor. For the? longest life, we recommend alkaline batteries (available at your local RadioShack store). ensor first, then in the {9 main unit, to give the main unit time to find the remote - . sensor's signal. Cautions: FCC ID: AAO6301026R FCC ID: AAO6301026R I 63-1026‘l’m 6 Tue Sep 22 [51:59:26 [998 69 - Dispose of old batteries promptly and properly. Do not burn or bury them. 0 Always remove old or weak batteries. Batteries can teak chemicals that can destroy electronic parts. in the Remote Sensor 1. Use a Phillips screwdriver to remove the screws in the battery compartment cover, then lift the cover to remove it. - 2. Set CHANNEL and ‘C/‘F inside the compartment to the desired settings. (See “Setting/Selecting the DISplay Channel” on Page 13 and “Changing the Degree For- mat” on Page 14.) .,,. f 3. Place two AA batteries in the compartment according to the polarity symbols (+ afid —) marked inside. 4. Use a pointed object (so-eh as a straightened paper clip) to press RESET and initiafiize the sensor’s transmitter. 5. Replace'the cover and reinsert and tighten the screws. G} FCC ID: AAO6301026R . ’ t?- 63-1026.fm 7 Tue Sep 22 1559261998 in the Main Unit 1. Remove the battery compartment cover by sliding it in the direction of the arrow marked on the cover. 2. Place two AA batteries in the compartment according to the polarity symbols (+ and —) marked inside. 3. Replace the cover. 4. Place the main unit next to the remote unit. Then use a pointed object (such as a straightened paper clip) to press RESET on the back of the unit and initialize the main unit’s receiver. When to Replace the Batteries When aft appears below the CHANNEL indicator on the top half of the main unit's dispi-‘ay, replace the batteries in the re- mote sensor for the select-3d channel. Low Battery - Indicators 5 63-1026.t‘m 8 Tue Sep 22 1545936 1998 4 FCC ID: AAO6301026R 61/ MM When ¢ appears in the lower half of the diSplay, replace the batteries in the main unit. Note: ¢i remains on the display for about 1 minute after you replace the batteries. ' MOUNTING You can place the main unit and remote sensor on flat sur- faces, or mount either on the wall using the supplied bracket (remote sensor) and screws (not supplied). Selecting a Location Choose locations for the’risain unit and remote sensor that are within 60-90 feet (20—30 meters) of each other. The main unit should be located indoors, but the remote sensor can be placed either indoors or out. The construction of your home or office might affect the transmission range between the “main unit and the remote sensor. If you have a choice of several locations, try each to see which provides the best performance. Cautions: - Do not place the main unit or remote sensor where it will be in direct sunlight. ' FCC ID: AAO6301026R ‘E 63-1026.fm 9 Tue Sep 22 [559261998 . 0 Do not place the main unit in a location where it is likely to get wet. Only the remote sensor is weather~resistant. - Do not place the main unit or remote sensor near electri- cal appliances or heating or air conditioning vents. Main Unit To set the main unit on a flat surface, pull the built-in stand away from the back of the unit. To mount the main unit on a wall, you need a Via-inch (3-mm) screw (not supplied) with a head that fits into the keyhole slot on the back of the main unit. 1. Drill a hole inithe wall atythe desired mounting location. 2. Thread a screw into the wall until the head extends about ‘14 inch from the wall. ..4-.4..,,v v l.‘lr-.-c—?~ .w-.:nA,-t f 6341026rm [0 Tue Sep 22 [5:59:26 1998 1? FCC ID: AAO6301026R ' {l} ‘.' ._.___-—-———-—-—————.__._.—.__ -. 3. Position the keyhole slo-f: over the screw and slide the thermometer down to ser‘jsure it. Remote Sensor Io set the remote sensor on a flat surface, insert the ends of the supplied wire stand into the holes on the back of the re- mote sensor. To mount the remote sensor on a wall (or on a post out— doors, tor example), you need two ‘la-inch (3-mm) screws (not supplied) with heads that fit into the keyhole slots on the back of the supplied mounting bracket. 10 {9 ti! 63—1026.fm tl Tue Sep 22 15:59:26 1998 H. . _ 1. Drill two holes iii/4 inches f into each hole, lettang the he the mounting surf-toe. apart. Then thread a screw ads extend about I/d inch from 2. Align the keyhole slots on the mounting bracket with the screws and slide the bracket downward to secure it. FCC ID: AA06301026R 63-1026.hn 12 Tue Sep 22 5:59:261998 OPERATION Once you install batteries in the remote'sensor and the main unit, the remote sensor displays its local' temperature and starts transmitting signals about every 30 seconds. The main unit starts searching for those signals. ' The temperature measured at the main unit appears on the bottom half of its display (indicated by @). Once the main unit receives the remote sensor's signal, the temperature measured at the remote sensor appears on the top half of the display. - Remote Sensor Temperature {9- ' Main Unit Temperature ; Note: If the main unit does not receive or stops receiving a signal from the remote sensor, it displays —- . - instead of a temperature. Try manuatly searching for a signal (see “Man- ually Searching for a Signal” on Page 18) or resetting the main unit (see “Resetting the,System” on Page 19). 12 FCC ID: AAO6‘301026R ,_ is g 63-1026.fm 13 Tue Sep 22§z5926 1998 FCC ID: AA06301026R Setting/Selecting the DiSpIay Channel Your thermometer system's main unit can display informa- tion for up to three different remote sensors Additional re- mote sensors (Cat. No. 63—1027) are available at your local RadioShack store Set CHANNEL 1/2/3 inside each remote sensor’s battery compartment to a different setting. CHANNEL To diaplay the temperature information for a remote sensor, repeatedly (if necessary) press CHANNEL on the main unit you see the channel number you set that sensor to use Channel Number Note: If you set two or nipre remote sensors to use- the same channel, the main unit displays temperature informa- tion for the remote sensor‘s signal it received first. 13 FCC ID-r’t AAO630‘1026R i 63—1026.fm 14 Tue Sep 22£59:26 1998 Changing the Degree Format You can view the temperature in Fahrenheit ('F) or Celsius (’C) format on' the main unit and on the remote sensor, and set each separately. To change the degree format displayed on the remote sen- sor, set ‘C /‘F inside the remote sensor's battery compart- ment to the desired setting. 14 FCC 1D: AAO6301026R 63~1026.fm 15 Tue Sep 22 6:07:001998 Reading the Temperature Trend Display The main unit displays the current temperature trend as ris- ing, steady, or falling. The trend is based on the average temperature measured at the selected channel’s remote sensor within the last 30 minutes. TEMP 7I'EMP TEMP TREND i;REND TREND Note: If your thermometer displays HH.H' or LL.L‘, this means that the temperature has exceeded or fallen below the thermometers measurement range (see “Specifications" on Page 22). When the temperature returns to within the measurement range, the display returns to normal. Reading the Kinetic Wave Display The kinetic wave display (directly above the CHANNEL number) shows the status of the signal being received by the main unit, The display consists of three graduated arcs above a solid dot. A 49 fa -—_ --——~.__...__..,,+ No Signal Searching/Receiving Signal 15 <9 {ijfiifiim‘j .. wa'fiix <4 6} l 63-1026.fm 16 Tue Sep 22555926 1998 —-—.__-_. signal. When the arcs appear one after another, the main unit is searching for or receiving a signal from the selected channel's remote sensor. Checking the Maximum/Minimum Temperatures The main unit stores the maximum (highest) and minimum (lowest) iocal temperatures and those of each remote sensor in its memory. Follow these steps to recall the maximum and minimum tem— ’ peratures stored since the last memory reset. 1. Repeatedly press CHANNEL on the main unit to select the desired channel. (MAX) and again to recall the minimum (MIN) tempera-_ ture. - 3. Press MEM again to return to the current temperature display. 16 FCC ID: AAO6301026R ”- . A “e. FCC 1D; AAO6301026R “H... __.._.. -.-...... 63-1026.fm 18 Tue Sep 22$107zlo 1998 ~ The highest limit you can set is +70' C (158' F). When you press A after reaching that limit, the range starts over at —50 ' C (_58', F). 4. To turn on the alarm tor the selected limit (HI or L0), press ON/OFF TEMP ALE so H]: or L0 appears. Or. press it so OFF appears to turn off that limit's alarm. 5. Repeat Steps 2—4 (if desired) to set the other limit and turn its alarm on or off, then press Ht/LO to return to the current temperature display. TROUBLESHOOTING {a Manually Searching for a Signal It the main unit displays —- . - instead of a temperature or it continuously displays a temperature different than that dis- played on the selected channel's remote sensor, thismeans the main unit has stopped receiving a signal from the sensor. Press CHANNEL and MEM at jhe same time on the main unit to have it manually search for“ a signal. ii; if the main unit still does not operate properly, try placing it or the remote sensor in a differef'jt location or resetting the sys- tem (see “Troubleshooting” on Page 18). - a 18 FCC ID: AAO6301026R I 63-1026.fm 19 Tue Sep 22555926 1998 Resetting the System If the main unit stops operating properly (and you have tried manually searching for a signal) use a pointed object (such as a straightened paper clip) to press RESET. This resets all display elements and temperature settings. If the remote sensor stops operating properly (and you have tried manually searching for a signal) use a pointed object 46} ‘ (such as a straightened paper clip) to press RESET inside the remote sensor’s battery compartment. This resets the displayed temperature and reinitializes the sensor’s trans- mitter. 19 J) FCC ID: AAO6301026R , FCC ID: AAO6301026R 63-1026.fm 20 Tue Sep 22é5>z59r26 1998 CARE AND MAINTENANCE Your FladioShack Indoor/Outdoor Thermometer is an exam- ple of superior design and craftsmanship. The following sug- gestions will help you care for your thermometer system so you can enjoy it for years. Keep the system away from dust and dirt, which can cause premature wear of parts. Handle the system gently and carefully. Drop- ping’a component can damage circuit boards and cases and can cause the systemto work improperly. Use only fresh batteries of the required size and recommended type. Batteries can leak chemicals that damage your system‘s elec- tronic parts. Wipe the system with a damp cloth occasion- ally to keep it looking new. Do not use harsh . chemicals, cleaning solvents, or strong deter- gents to clean the system's components. Modifying or tampering with the thermometer system's inter- nal components can cause a malfunction and might invali- date its warranty. If your; thermometer system is not performing as it should, take it to your local FladioShack store for assistance. - 20 69 I _ l 63-1026.fm 21 Tue Sep 2255926 1998 FCC INFORMATION This equipment complies with the limits for a Class 8 digital device as specified in Part 15 of FCC Rules. These limits provide reasonable protection against radio and TV interfer- ence in a residential area. However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference, you can try one or more of the following correctivefimeasures: ' Reorient or relocate the receiving antenna. 0 increase the distancefrbetweenfihe equipment and the radio or TV. - ' {I} Consult your local Radio Shack store if the problem still ex- 6} ists. ' -21 FCC ID: ‘AAO6301026B FCC ID: AAO6301026R 63—1026.fm 22 Tue Sep 22é§9126 1998 ~. _ SPECIFICATIONS Power ................................... Main Unit: 3V with Two AA Batteries Remote Sensor: 3V with Two AA Batteries Note: At temperatures below —4‘ F (—20‘ C), use lithium batter- ies (Cat. No. 234564.) in the remote sensor. Range ....................................................... Main Unit: 23‘ to 122° F (—5° to 50' C) Remote Sensor (using alkaline batteries): —4' to 140' F (—20' to 60' C) Remote Sensor (using lithium batteries): -50' to 140° F (-45' to 60‘ C) Resolution ................................................................ 0.2' F (0.1 ’ C) Sampling Cycle (Approximate) ..................... Main Unit: 10 Seconds Remote Sensor: 30 Seconds Accuracy ....................... Main Unit: i4' at 23‘ to 32' F (-—5° to 0’ C) 1-2' at 32' to 104' F (0' to 40‘ C) i4' at 104' to i22' F (40° to 50°_ C) Remote Sensor: i4' at —4‘ to 32‘ F (-—20' to 0’ C) i2' at 32' to 104° F (0' to 40‘ C) 14' at 104’ to 122' F(40° to 50‘ C) $6 at 122' to 140' F (50' to 60’ C) Weight (without batteries) ......................... Main Unit: 5.7 oz (162 g)’ Remote Sensor: 3.5 oz (100 9) Dimensions .................................. Main Unit: 45/8 x 43/15 x 1 Inches , (117 x10? x 26 mm) Remote Sensor: 4‘115 X 21/16 x ”As inches (103 x 68 x 21 mm) Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice. 22 1' (T. , 63-1026.fm 23 Tue Sep 22é§z59z26 1998 M— NOTES FCC ID: AAO6301026R ' t wreaths 63-1026.Frtt 24 Tue Sep 2261355926 1998 FCC ID: AA06301026R_ Limited Ninety-Day Warranty _ This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date oi purchase ADVISED OF THE POSSIBILITY OF SU Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages. so the above limitations or exclu- sions may not apply to you. “in the event of a product defect during the warranty period. take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. Ra- dioShack will. at its option. unless otherwise provided by law: (a) correct the detect by product repair without charge lor parts and labor; (b) replace the product with one oi the same or srmrlar design; or (c) refund the purchase price. All replaced parts and products. and products on which a refund is made. become the property ol Fia- dioShack. New or reconditioned parts and products may be used in the performance of warranty serwce. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replace- ment of the product made after the expiration of the warranty period. This warranty does not cover: (a) damage or failure caused by or attributable to acts of God. abuse. accident. misuse. improper-or abnormal usage. failure to follow in- structions. improper installation or maintenance. alteration. lightning or other inci- dence of excess voltage or current: (by any repairs other than those provided by a RadioShack Authorized Service Facility} (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation. shipping or insurance costs; or it) costs or product removal, installation. set-up sea/ice adjustment or reinstallation. This warranty gives you specific legal'fzrights, and you may also have other rights which vary from state to state. “ ~ RadioShack Customer Relations, Dept. W. 100 Throckmorton St.. Suite 600. Fort Worth, TX 76102 ~ We Service What We Sell 3m RadioShack A Division of Tandy Corporation Fort Worth, Texas 76102 09A98N ' Printed in Hong Kong
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Modify Date : 1998:10:08 19:35:57 Create Date : 1998:10:08 19:34:41 Producer : Pixel Translations (PIXPDF Ver.1.35) Creator : Acrobat 3.0 Import Plug-in Page Count : 24EXIF Metadata provided by EXIF.tools