Radio Shack 3201258T Wireless Microphone User Manual

RadioShack Corporation Wireless Microphone

User manual

Step 4 Set TALK-MUTE-OFF switch to TALK. Then turn the audio source and receiver volume up to the desired level. The READY indicator light displays indicating that the microphone signals are within range of the receiver.•    To avoid the popping noise that may occur  when switching from OFF to TALK, use MUTE.         TALK-MUTE-OFF to OFF. verify they operate at different frequencies. See your microphone or receiver for its frequency.Step 3 Press POWER on the receiver to turn it on. The POWER indicator lights up. Fully extend the antennae.Fully extend the antennae. Set the volume on your PA amplier or other audio source to a minimum level. Then turn power on.•  Dispose of old batteries promptly and properly. •  Do not burn or bury batteries.•  Use only fresh batteries of the required size and recommended type.•  Do not mix batteries of different sizes or types.•  If you do not plan to use your microphone system for a chemicals that can damage electronic parts. RadioShack. Your from the receiver allowing you to move freely.microphone      receiver9V AC adapter      user’s guidewhat’s includedbattery notes32-1258170MHz Single Channel Wireless Microphone SystemFrequency ............. 169.505MHz, 170.245MHz or 171.905MHzOperating Range ............................................ 200 feet (Typical)Frequency Response ..........................................120---13000HzmicrophoneRF Power ........................................................................ 10dBmSensitivity............................................ 106 dB SPL at 7KHz FMPower Source ................................................Two AA BatteriesreceiverSensitivity with S/N 20dB ....................................................1uVS/N Ratio at 1mV RF Input .................................................75dBImage Rejection .................................................................55dBLine Output .....................................................................510mV Microphone Output ..........................................................10mVPower Requirement ................................................ AC Adapterwithout notice. Product may vary from depiction.specicationsWarning: Modifying, tampering with, or adjusting this unit, or replacing any transmitter component (crystal, semiconductor, etc.) may result in a violation of the FCC rules.Consult your local RadioShack store or an experienced radio/TV technician for help.If you cannot eliminate the interference, the FCC requires that you stop using your microphone system. Changes or modications not expressly approved by RadioShack may cause interference and void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device may not cause harmful interference.This wireless microphone system complies with Part 90 of the FCC Rules. There are three frequencies available for the system. You must obtain a license for each frequency you plan to use before operating your system. One license can include both frequencies. Visit http://wireless.fcc.gov/uls/, or call your local FCC ofce to apply for your license. Your ability to obtain a license will depend on how you plan to use the system.For RF exposure“IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the system exceeding the RF exposure requirements.”For devices less than 200mW ERPSAFETY INFORMATIONYour wireless microphone contains a low power transmitter. When the EUT is powered on, it sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for wireless devices.IMPORTANTTo maintain compliance with the FCC’s RF exposure guidelines, hold the transmitter and antenna at least 1 inch (2.5 centimetres) from your face and speak in a normal voice, with the antenna pointed up and away from the face. Ensure that the antenna is at least 1 inch (2.5 centimetres) from your body when you are using your wireless microphone. Use only the supplied antenna. Unauthorized antennas, modications, or attachments could damage the transmitter and may violate FCC regulations.rf emission information©2006. RadioShack Corporation. All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.32-125804A06 AO0262AAA1 Printed in China This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers. For complete warranty details and exclusions, check with your local RadioShack store.RadioShack Customer Relations 300 RadioShack Circle, Fort Worth, TX 76102    04/04limited one-year warrantyPlease read this user’s guide before installing, setting up and using your new product.www.radioshack.comConnect your receiver to the input jack on your amplier using the LINE jack.(Optional) Connect your receiver to your amplier with the MICROPHONE jack.Plug the AC adapter into an outlet.SQUELCHRotate to limit the background noise and control the transmitting distance. To increase the transmitting distance, rotate it to MIN.POWER indicatorReplace the batteries when light is off.POWER indicatorREADY indicatorPOWER buttonTALK-MUTE-OFFVOLUMERotate to adjust your microphone’s volume.NOTESStep 2 Unscrew the microphone grille and remove the battery cover. Insert two AA batteries with correct polarity. Then replace the battery cover and the microphone grille.Twist Step 1 Set the volume to a minimum level and plug in the AC adapter. Then, using a shielded audio cable (notusing a shielded audio cable (not included), connect the LINE jack on your receiver to the input jack on your amplier, or other device Optionally, or if the input jack is in use, you canif the input jack is in use, you can connect using the MICROPHONE jacks on your receiver and amplier with a 1/4” audio cable (not included).NOTE

Navigation menu