Radio Shack 4301122D 900MHz ISM Band Cordless Telephone User Manual www RadioShack with CircleR eps

RadioShack Corporation 900MHz ISM Band Cordless Telephone www RadioShack with CircleR eps

users manual

Owner’s ManualPlease read before using this equipment.900MHz Cordless Telephonewith Call Waiting/Caller ID43-1122.C.fm  Page 1  Wednesday, December 13, 2000  1:56 PM
2Read This Before InstallationˆRead This Before InstallationThis telephone has been tested and found tocomply with all applicable UL and FCC stan-dards.We have designed your 900MHz CordlessPhone with Call Waiting/Caller ID to conformto federal regulations, and you can connect itto most telephone lines. However, each de-vice, such as a telephone or answering ma-chine, that you connect to the telephone linedraws power from the telephone line. We re-fer to this power draw as the device's ringerequivalence number, or REN. The REN is onthe bottom of your phone.If you use more than one phone or other de-vice on the line, add up all of the RENs. If thetotal is more than five (three in rural areas),your telephones might not ring. If ringer oper-ation is impaired, remove a device from theline.FCC STATEMENTYour telephone complies with Part 68 of FCCRules. You must, upon request, provide theFCC registration number and the REN toyour telephone company. Both numbers areon the bottom of your telephone.Note: You must not connect your telephoneto:• coin-operated systems• party-line systems• most electronic key telephone systemsTHE FCC WANTS YOU TO KNOWIn the unlikely event that your phone causesproblems on the phone line, the phone com-pany can temporarily discontinue your ser-vice. If this happens, the phone companyattempts to notify you in advance. If advancenotice is not practical, the phone companynotifies you as soon as possible and advisesyou of your right to file a complaint with theFCC.Also, the phone company can make changesto its lines, equipment, operations, or proce-dures that could affect the operation of thistelephone. The telephone company notifiesyou of these changes in advance, so you canWARNING: To reduce the risk of fire orshock hazard, do not expose this product to rainor moisture.CAUTIONRISK OF ELECTRIC SHOCK. DO NOT OPEN.CAUTION: TO REDUCE THE RISK OFELECTRIC SHOCK, DO NOT REMOVECOVER OR BACK. NO USER-SERVICE-ABLE PARTS INSIDE. REFER SERVICINGTO QUALIFIED PERSONNEL.This symbol is intended to alertyou to the presence of uninsu-lated dangerous voltage withinthe product’s enclosure that mightbe of sufficient magnitude to con-stitute a risk of electric shock. Donot open the product’s case.This symbol is intended to informyou that important operating andmaintenance instructions areincluded in the literature accom-panying this product.!!© 2000 RadioShack Corporation.All Rights Reserved.RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.43-1122.C.fm  Page 2  Wednesday, December 13, 2000  1:56 PM
3Read This Before Installationtake the necessary steps to prevent interrup-tion of your telephone service.LIGHTNINGYour telephone has built-in protection circuitsto reduce the risk of damage from surges intelephone line and power line current. Theseprotection circuits meet or exceed the FCCrequirements. However, lightning striking thetelephone or power lines can damage yourtelephone.Lightning damage is not common. Neverthe-less, if you live in an area that has severeelectrical storms, we suggest that you unplugyour phone when storms approach to reducethe possibility of damage.IMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment, ba-sic safety precautions should always be fol-lowed to reduce the risk of fire, electric shockand injury to persons, including the following:1. Read and understand all instructions.2. Follow all warnings and instructionsmarked on the product.3. Never install telephone wiring during alightning storm.4. Never install telephone jacks in wetlocations unless the jack is specificallydesigned for wet locations.5. Never touch uninstalled telephone wiresor terminals unless the telephone linehas been disconnected at the networkinterface.6. Use caution when installing or modifyingtelephone lines.7. Do not fix the AC power supply cord tobuilding surfaces with metal fittings (ifthe product has an AC power cord).8. Unplug this product from the wall outletbefore cleaning. Do not use liquid clean-ers or aerosol cleaners. Use a dampcloth for cleaning. 9. Do not use this product near water, forexample, near a bathtub, wash bowl,kitchen sink, or laundry tub, in a wetbasement, or near a swimming pool.10. Do not place this product on an unstablecart, stand, or table. The product mayfall, causing serious damage to theproduct.11. Slots and openings in the cabinet andthe back or bottom are provided for ven-tilation. To protect it from overheating,these openings must not be blocked orcovered. The openings should never beblocked by placing the product on a bed,sofa, rug, or other similar surface. Thisproduct should never be placed near orover a radiator or heat register. Thisproduct should not be placed in a built-ininstallation unless proper ventilation isprovided.12. This product should be operated onlyfrom the type of power source indicatedon the marking label. If you are not sureof the type of power supply to yourhome, consult your local power com-pany.13. Do not allow anything to rest on thepower cord. Do not locate this productwhere the cord will be stepped on.14. Do not overload wall outlets and exten-sion cords as this can result in a risk offire or electric shock.15. Never push objects of any kind into thisproduct through cabinet slots as they43-1122.C.fm  Page 3  Wednesday, December 13, 2000  1:56 PM
4Read This Before Installationmay touch dangerous voltage points orshort out parts that could result in a riskof fire or electric shock. Never spill liquidof any kind on the product.16. To reduce the risk of electric shock, donot disassemble this product. Take it toa qualified service technician when ser-vice or repair work is required. Openingor removing covers may expose you todangerous voltage or other risks. Incor-rect reassemble can cause electricshock when the product is subsequentlyused.17. Unplug this product from the wall outletand refer servicing to qualified servicepersonnel under the following condi-tions:• When the power cord plug is dam-aged or frayed.• If liquid has been spilled, into theproduct.• If the product has been exposed torain or water.• If the product does not operate nor-mally by following the operatinginstructions. Adjust only those con-trols that are covered by the operat-ing instructions because improperadjustment of other controls mayresult in damage and will oftenrequire extensive work by a qualifiedtechnician to restore the product tonormal operation.• If the product has been dropped orthe cabinet has been damaged. • If the product exhibits a distinctchange in performance.18. Avoid using a telephone (other than acordless type) during an electrical storm.There may be a remote risk of electricshock from lightning.19. Do not use the telephone to report a gasleak in the vicinity of the leak.Battery Safety InstructionsCaution: To reduce the risk of fire or injury,read and follow these instructions.1. Use only the appropriate type and sizebattery pack specified in the instructionmanual provided for this product.2. Do not dispose of the battery pack in afire. The cell may explode. Check withlocal codes for possible special disposalinstructions.3. Do not open or mutilate the batterypack. Released electrolyte is corrosiveand may cause damage to the eyes orskin. It may be toxic if swallowed.4. Exercise care in handling the batterypack in order not to short it with conduct-ing materials such as rings, bracelets,and keys. The battery or conductor mayoverheat and cause burns.5. Charge the battery pack provided oridentified for use with this product only inaccordance with the instructions andlimitations specified in the instructionmanual provided for this product.6. Observe proper polarity orientationbetween the battery pack and batterycharger.SAVE THESE INSTRUCTIONS43-1122.C.fm  Page 4  Wednesday, December 13, 2000  1:56 PM
5ContentsˆContentsFeatures ..................................................................................................................................  6Installation ..............................................................................................................................  7Selecting a Location ............................................................................................................  7On a Desk Top  ................................................................................................................  7On a Wall Plate  ...............................................................................................................  8Connecting and Charging the Battery Pack  ........................................................................  9Setting the Dialing Mode  ...................................................................................................  10Setting the Ringer Tone and Volume .................................................................................  10Turning Auto Talk On/Off .................................................................................................... 11Turning Caller ID/Call Waiting On/Off ................................................................................. 11Storing Your Area Code ...................................................................................................... 11Operation ..............................................................................................................................  12Making and Receiving Calls ..............................................................................................  12Selecting the Channel  .......................................................................................................  12Adjusting the Handset’s Volume ........................................................................................  12Using Redial ......................................................................................................................  12Using Flash  .......................................................................................................................  12Using Tone Services on a Pulse Line ................................................................................  13Paging ...............................................................................................................................  13Using a Headset ................................................................................................................ 13Memory Dialing  ................................................................................................................. 13Storing a Number and Name in Memory  ......................................................................  13Entering a Pause  ..........................................................................................................  14Editing or Deleting a Number in Memory  ......................................................................  14Reviewing Memory Numbers ........................................................................................  15Dialing a Memory Number  ............................................................................................  15Chain-Dialing Service Numbers ....................................................................................  15Testing Stored Emergency Numbers  ............................................................................  15Caller ID Operation  ..............................................................................................................  16Important Caller ID Information  .........................................................................................  16Reviewing Caller ID Records  ............................................................................................  16Caller ID Messages .......................................................................................................  16Adding/Deleting the Area Code .........................................................................................  17Dialing Numbers from a Caller ID Record .........................................................................  17Storing a Caller ID Record in Memory ...............................................................................  17Deleting Caller ID Records ................................................................................................  17Deleting a Single Caller ID Record  ...............................................................................  17Deleting All Caller ID Records  ......................................................................................  17Troubleshooting ...................................................................................................................  18Care ...................................................................................................................................  1943-1122.C.fm  Page 5  Wednesday, December 13, 2000  1:56 PM
6FeaturesˆFeaturesYour RadioShack 900 MHz Cordless Tele-phone uses advanced technology to give yousuperior audio quality and extended range.The phone’s Caller ID unit records each call-er’s telephone number (and name, if avail-able in your area) and the date and time ofthe call, as provided by your local phonecompany to Caller ID service subscribers. Ifyou subscribe to Call Waiting with Caller ID,the phone shows you the incoming caller in-formation, even when you are already talkingon the phone.Your phone’s other features include:10-Number Memory Dialing — lets youstore up to 10 numbers in memory for easydialing.Headset Jack — lets you connect an option-al headset for hands-free convenience.Hearing-Aid Compatibility — lets you usethe phone with hearing aids that have a T(telephone) switch.20-Record CID Capacity — stores up to 20call records in Caller ID.Volume Control — lets you adjust thevolume you hear through the handset.Page — lets you send a signal from the baseto the handset to page someone or to helpyou locate the handset.Adjustable Ringer/Tone Volume — letsyou choose between two volumes and tonesfor the phone’s ringer.Facedown or Faceup Handset Charging— you can place the handset on the basefacedown or faceup to show the Caller IDdisplay.Ample Talk and Standby Time — the sup-plied battery (when fully charged) providesabout 7 hours of talk time or 7 days of stand-by time.Security Access-Protection Code — auto-matically prevents other cordless phone us-ers from using your phone line while thehandset is off the base.Auto Talk — lets you set the phone to an-swer a call by simply lifting the handset fromthe base.Important:• Cordless phones such as this onerequire AC power to operate. When thepower is off, you cannot make or receivecalls using your phone. To be safe, youshould also have a phone that does notneed AC power to operate (not a cord-less phone), so you can still make andreceive calls if there is an AC power fail-ure.• When AC power is lost, the phone losesthe security access-protection code con-nection between the base and the hand-set. When power is restored, put thehandset on the base briefly to restorethis connection so you can use thehandset.• Your phone operates on standard radiofrequencies as allocated by the FCC. Itis possible for other radio units operatingnearby on similar frequencies to unin-tentionally intercept your conversation orcause interference. This possible lack ofprivacy can occur with any cordlessphone.43-1122.C.fm  Page 6  Wednesday, December 13, 2000  1:56 PM
7InstallationˆInstallationSELECTING A LOCATIONYou can place the phone’s base on a desk ortable, or mount it on a standard wall plate ordirectly on a wall. Select a location that is:• near an accessible AC outlet • near a telephone line jack• out of the way of normal activities• away from electrical machinery, electri-cal appliances, metal walls or filing cabi-nets, wireless intercoms, alarms, androom monitors• away from other cordless phonesThe base’s location affects the handset’srange. If you have a choice of several loca-tions, try each to see which provides the bestperformance.Cautions:You must use a Class 2 powersource that supplies 9V DCand delivers at least 210 mA.Its center tip must be set to positive andits plug must fit the phone's DC IN 9Vjack. The supplied adapter meets thesespecifications. Using an adapter thatdoes not meet these specificationscould damage the phone or the adapter.• Always connect the AC adapter to thephone before you connect it to ACpower. When you finish, disconnect theadapter from AC power before you dis-connect it from the phone.Your telephone connects directly to a modu-lar telephone line jack. If your telephone wir-ing does not have a modular jack, you canupdate the wiring yourself using jacks andadapters (available at your local RadioShackstore), or have the telephone company up-date the wiring for you. You must use com-patible modular jacks that are compliant withPart 68 of FCC Rules.Note: The USOC number of the jack to beinstalled is RJ11C (or RJ11W for a wall platejack).On a Desk TopFollow these steps to place the base on adesk, shelf, or table. 1. Plug one end of the supplied long modu-lar cord into the TEL LINE jack on theback of the base.2. Plug the modular cord’s other end into amodular phone line jack.3. Insert the supplied AC adapter’s barrelplug into the DC IN 9V jack on the back ofthe base.4. Route the adapter’s cord through thestrain relief slot on the base.5. Plug the adapter into a standard AC out-let.6. Lift the base’s antenna to a vertical posi-tion.!Strain Relief Slot43-1122.C.fm  Page 7  Wednesday, December 13, 2000  1:56 PM
8InstallationOn a Wall Plate1. Plug one end of the supplied short mod-ular cord into the TEL LINE jack on theback of the base.2. Insert the supplied AC adapter’s barrelplug into the DC IN 9V jack on the back ofthe base.3. Route the adapter and modular cordsthrough the grooves on the bottom ofthe base.4. Plug the short modular cord into the wallplate jack, then align the base’s keyholeslots with the wall plate studs and slidethe base down to secure it.5. Plug the adapter into a standard AC out-let.6. Push up on the handset holder, then liftand remove it. Turn it over and rotate itso that the oval-shaped indention is atthe bottom, then slide it down into itsslot. Snap it back into place so that itholds the handset.On a WallTo mount the phone directly on a wall, youneed two screws (not supplied) with headsthat fit into the keyhole slots on the bottom ofthe base.1. Drill two holes 315/16inches (100 mm) apart.Then thread a screwinto each hole, lettingthe heads extend about1/8 inch (3 mm) from thewall.2. Plug one end of the supplied long modu-lar cord into the TEL LINE jack on theback of the base.3. Insert the supplied AC adapter’s barrelplug into the DC IN 9V jack on the back ofthe base.4. Route the adapter and modular cordsthrough the grooves on the bottom ofthe base.5. Align the bracket’s keyhole slots with themounting screws and slide the basedownward to secure it.AC Cord Modular Telephone Cord43-1122.C.fm  Page 8  Wednesday, December 13, 2000  1:56 PM
9Installation6. Plug the modular cord’s other end intothe phone jack, and plug the adapterinto a standard AC outlet.CONNECTING AND CHARGING THE BATTERY PACKThe phone comes with a rechargeablenickel-cadmium battery pack in the handset,but not connected. Before using your phone,you must connect the battery pack, thencharge it for about 24 hours.1. Press down and slide off the batterycompartment cover.2. Lift the battery pack out of the compart-ment. 3. Plug the battery pack’s connector intothe socket in the compartment (the con-nector fits only one way), then place thebattery pack in the compartment.4. Replace the cover.To charge the battery pack, place the hand-set either faceup or facedown on the base.The CHARGE/IN USE indicator on the baselights and Total:00 appears on the hand-set display.Recharge the battery pack when Low Bat-tery flashes on the display.Important: Be sure the battery pack is prop-erly connected before you try to charge it.The CHARGE/IN USE indicator lights whenthe handset is on the base, even if the bat-tery pack is not connected. Notes:• When you first use the phone aftercharging or recharging the battery pack,the phone might not work and you mighthear an error tone when you pressTALK. Return the handset to the base forabout 5 seconds to reset the securityaccess-protection code.• If the base loses power for about anhour while the handset is away from it,the security access-protection codemight be lost. To reset the code, returnthe handset to the base for about 5 sec-onds.The handset does not lose its securityaccess-protection code even if the bat-tery pack is completely discharged.• Using a pencil eraser, clean the charg-ing contacts on the handset and baseabout once a month.• If the battery pack becomes weak duringa call, the handset beeps every 3 sec-onds and Low Battery flashes. Whenthis happens, you cannot make a calluntil you recharge the battery pack.• About once a month, fully discharge thebattery by keeping the handset off thebase until Low Battery flashes onthe display. Otherwise, the battery packloses its ability to fully recharge.• If the display is blank and the phonedoes not work, recharge the batterypack. (The battery power might be toolow to light the display.)• If you are not going to use your phonefor an extended period, disconnect thebattery pack. This increases the batterypack’s usable life.43-1122.C.fm  Page 9  Wednesday, December 13, 2000  1:56 PM
10 Installation• The supplied battery pack should last forabout a year. If the battery pack doesnot hold a charge for more than 2 hoursafter an overnight charge, replace it witha new 3.6-volt, 600 mAh battery packwith a connector that fits the socket inthe battery compartment. You can ordera replacement battery pack through yourlocal RadioShack store. Install the newbattery pack and charge it for about 24hours.Warning: Dispose of the old battery packpromptly and properly. Do not burn or bury it.See “Battery Safety Instructions” on Page 4for additional information on proper batteryhandling.If you have trouble replacing the batterypack, take the phone to your localRadioShack for assistance.Important: The EPA certifiedRBRC® Battery Recycling Sealon the nickel-cadmium (Ni-Cd)battery indicates RadioShackis voluntarily participating in anindustry program to collect and recycle thesebatteries at the end of their useful life, whentaken out of service in the United States orCanada. The RBRC program provides a con-venient alternative to placing used Ni-Cd bat-teries into the trash or the municipal wastestream, which may be illegal in your area.Please call 1-800-THE-SHACK (1-800-843-7422) for information on Ni-Cd battery recy-cling and disposal bans/restrictions in yourarea. RadioShack’s involvement in this pro-gram is part of the company’s commitment topreserving our environment and conservingour natural resources.SETTING THE DIALING MODEYour phone is set for tone dialing. If you havepulse service, change the dialing mode. Ifyou are not sure which type of service youhave, do this test.1. Lift the handset, press TALK, and listenfor a dial tone.2. Press any number other than 0.Note: If your phone system requires thatyou dial an access code (9, for example)before you dial an outside number, donot dil the access code either.If the dial tone stops, you have touch-tone service. If the dial tone continues,you have pulse service.3. Press TALK.To set the dialing mode, hold down FLASHuntil the phone beeps and Pulse Dial-ing or Tone Dialing appears. Press #/7777 to set pulse mode or ∗/TONE to set tonemode.Notes:• The phone exits the setting mode if acall or page is received, or if you pressTALK.• If the battery pack power becomes toolow, the dial mode might reset to tone. Ifyou are on a pulse line and cannot makea call, hold down FLASH to check thecurrent dialing mode. Set to pulse modeif necessary.SETTING THE RINGER TONE AND VOLUMEYou can select one of four different ringertone/volume settings on the handset. Lift thehandset and repeatedly press 8888 or 9999 toselect the desired ringer setting. Each timeyou press the button, the phone rings at theselected setting and the display shows RingType A High, Ring Type A Low,43-1122.C.fm  Page 10  Wednesday, December 13, 2000  1:56 PM
11InstallationRing Type B High, or Ring Type BLow. TURNING AUTO TALK ON/OFFYour phone is preset so you must pressTALK when you lift the handset from the baseto answer a call. With Auto Talk turned on,you can answer a call by just lifting the hand-set from the base. If the handset is awayfrom the base, you can answer by pressingany key. Follow these steps to turn Auto Talk on oroff.1. Lift the handset and hold down CALL IDuntil the menu appears with AutoTalk selected.2. Press SELECT to change the Auto Talksetting. On or Off appears indicatingthe selected setting.3. Return the handset to the base (or pressCALL ID) to store the new setting.TURNING CALLER ID/CALL WAITING ON/OFFIf you subscribe to Call Waiting with Caller IDservice, you can set the phone to show Call-er ID information for an incoming call evenwhile you are using the phone.Follow these steps to turn the Caller ID/CallWaiting feature on or off.1. Lift the handset and hold down CALL IDuntil the menu appears with AutoTalk selected.2. Press  2 or 9999 to move the cursor toCIDCW: (Caller ID/Call Waiting).3. Press SELECT to turn the Caller ID/CallWaiting setting on or off. On or Offappears indicating the selected setting.4. Return the handset to the base to storethe new setting.STORING YOUR AREA CODEYou can store your local area code in thephone’s memory so it will not store the areacode if you receive a local call. If you need toadd or store the area code for a local num-ber, you can add it afterwards (see “Adding/Deleting the Area Code” on Page 17).Important: In some areas, the area code isnecessary even for a local call. If you live insuch an area, do not store the area code.Follow these steps to store your area code.1. Lift the handset and hold down CALL IDuntil the menu appears with AutoTalk selected.2. Press  3 or 9999 to move the cursor toArea Code:.3. Press  SELECT, then enter your three-digit area code. If you make a mistake,repeatedly press 6666 or 7777 to move thecursor over the incorrect digit, then enterthe correct number.Note: If an area code is already stored,it appears on the display after you holddown  CALL ID. Press DELETE threetimes to delete the area code. Thenenter your area code.4. Press  SELECT to store the area code,then press CALL ID or return the handsetto the base to clear the display.43-1122.C.fm  Page 11  Wednesday, December 13, 2000  1:56 PM
12 OperationˆOperationThe handset window has plastic film on it toprotect it during shipment. Carefully peel offthe film before using your phone.MAKING AND RECEIVING CALLSTo make a call, lift the handset and pressTALK. Talk and the current volume settingappear on the handset’s display, and theCHARGE/IN USE indicator on the baselights. Dial the number. The number appearson the handset as you dial, then the call’selapsed time appears. To end a call, placethe handset on the base or press TALK.You can also dial the number before youpress TALK. If you make a mistake, pressDELETE until the incorrect entry is erased,then enter the correct number. To delete theentire number, hold down DELETE.When you receive a call, Incoming Callappears. To answer the call, lift the handsetand press TALK. If Auto Talk is on, just lift thehandset. If the handset is away from thebase, press any key. Talk appears on thehandset’s display. To end a call, place thehandset on the base or press TALK.SELECTING THE CHANNELThe phone has 40 channels. If the call dis-connects or you experience difficulty hearingthe conversation during a call, press CH onthe handset to select a different channel.Scanning appears as your phone search-es for a clear channel.ADJUSTING THE HANDSET’S VOLUMETo adjust the volume of the sound you hearthrough the handset during a call, press 8888or 9999 on the handset until you obtain the de-sired volume level. Volume Maximum,Volume High,  Volume Medium, orVolume Low appears on the handset dis-play. Once you set the volume level, the set-ting is maintained even after you hang up thephone.Note: When you press 8888 while the volumeis maximum or 9999 while the volume is low,the setting does not change. The phonesounds three short beeps.USING REDIALYou can quickly dial the last number you di-aled. Lift the handset and press REDIAL/PAUSE, then TALK. The phone dials the num-ber.Notes:• You can also press REDIAL/PAUSE afterpressing TALK.• The redial memory holds up to 32 digits,so you can redial long-distance as wellas local numbers.• The redial memory also holds pauseentries (see “Entering a Pause” onPage 14).USING FLASHFLASH performs the electronic equivalent ofa switchhook operation for special services,such as Call Waiting. For example, if youhave Call Waiting, press FLASH to answer anincoming call without disconnecting the cur-rent call. Press FLASH again to return to thefirst call.Note: If you do not have any special phoneservices, pressing FLASH might disconnectthe current call.43-1122.C.fm  Page 12  Wednesday, December 13, 2000  1:56 PM
13OperationUSING TONE SERVICES ON A PULSE LINESome special services require tone signals(such as bank-by-phone). If you have pulsedialing, you can still use these special toneservices. Dial the service’s main number. When theservice answers, press ∗/TONE. Any addi-tional numbers you dial are sent as tone sig-nals.The phone’s dial mode resets to pulse whenyou make or receive a call.PAGINGTo send a page from the base to the handsetor to locate the handset when the phone isnot in use, press PAGE/FIND on the base.The handset beeps for 15 seconds.To locate the handset using a continuousbeep, press and hold PAGE/FIND longer than2 seconds. The handset beeps for 1 minute.If you still cannot locate the handset, releasePAGE/FIND, then press again. The handsetbeeps for another minute.To stop the page, press any key on thehandset, place the handset on the base, orpress PAGE/FIND on the base again.Note: The phone rings when a call comes inwhile you are using the page feature.USING A HEADSETYou can make or answer calls with hands-free convenience using an optional headsetthat has a 3/32-inch (2.5-mm) plug. Your localRadioShack store has a variety of headsetsavailable. To connect the headset, gently flip open therubber headset jack cover on the side of thehandset, then insert the headset’s plug intothe jack.Notes:• Connecting a headset disconnects thehandset’s earpiece and microphone.•8888 or 9999 on the handset also controlsthe headset’s volume.• If you place the handset on the base torecharge it while the headset is con-nected, be sure the handset seats prop-erly.• With a headset connected, you canmake or answer calls as usual using thekeys on the handset.• You can use a handset holder (availablefrom your local RadioShack store) tohang the handset on your belt forgreater convenience when using aheadset.• When you finish using the headset, dis-connect it from the handset and closethe rubber cover to protect the jack.MEMORY DIALINGYou can store up to 10 phone numbers andnames in memory, then dial a stored numberby entering its memory location number.Each number can be up to 20 digits, andeach name can be up to 14 characters.Storing a Number and Name in Memory1. Lift the handset.2. Hold down MEM until Memory Storeand a list of memory location numbersappears.3. Select an empty memory location (or theone you want to replace) by entering thelocation number (1–0) or using 8888 or 9999to scroll through the list.43-1122.C.fm  Page 13  Wednesday, December 13, 2000  1:56 PM
14 Operation4. Press SELECT. Store Name appears.If you do not want to enter a name, skipto Step 6. 5. To enter a name, use the number keys.Refer to the letters on the number keysto select the desired letter. Press the keyonce for the first letter in the upper case,press twice for second letter in the uppercase, and so on. To enter the lower caseletter, press four times (or five times) todisplay the first letter in lower case, fiveor six times for second letter, and so on. For example, to enter John: press 5once; upper case J appears. Thenpress 6 six times; lower case o appears.Press 4 five times; lower case happears. Finally, press 6 five times;lower case n appears.To enter two letters from the same key ina row, press #/7777 to move the cursor tothe next position. For example to enterAB, press 2; A appears. Then press #/7777, the cursor moves to next position,then press 2 twice so B appears.To enter a space, press #/7777 twice with-out entering any character.To enter a number, repeatedly press thecorresponding number key until thenumber appears. To enter a special character, press 0.Each time you press 0, the followingcharacters appear in this order:∗ # – & ( ) (space) 0If you make a mistake, use ∗/TONE/6666or  #/7777 to move the cursor over theerror, then enter the correct character, orpress DELETE to delete a character. Todelete all characters, hold down DELETEfor at least 1 second.6. Press  SELECT.  Store Numberappears.7. Enter the number and any tone andpause entries (see “Using Tone Serviceson a Pulse Line” on Page 13 and “Enter-ing a Pause” on Page 14).Note: Each tone or pause entry usesone digit of memory.8. Press  SELECT. The phone beeps andMemory n Stored appears (n = num-ber). After two seconds, MemoryStore appears, and you can repeatSteps 3–8 to store more numbers.To replace a stored number, simply store anew one in its place.Entering a PauseIn some telephone systems, you must dial anaccess code (9, for example) and wait for asecond dial tone before you can dial an out-side number. You can store the access codewith the phone number. However, youshould also store a pause after the accesscode to allow the outside line time to con-nect. To enter a 2-second pause, press REDIAL/PAUSE. You can add more pause entries fora longer pause.Editing or Deleting a Number in Memory1. Lift the handset.2. Hold down MEM until Memory Storeand a list of memory location numbersappear on the handset display.3. Choose a memory location (1–0) bypressing a number or by repeatedlypressing 8888 or 9999.43-1122.C.fm  Page 14  Wednesday, December 13, 2000  1:56 PM
15Operation4. Press  SELECT. Three options (EditMemory n,  Delete Memory n andGo Back) appear. Press 8888 or 9999 tochoose the option then press SELECT tochoose it.Edit Memory n — edit the record asdescribed in Steps 5 through 8 of “Stor-ing a Number and Name in Memory” onPage 13.Delete Memory n — the displayprompts you to confirm the deletion.Press 8888 or 9999 to move the cursor toYes, then press SELECT or DELETE.The phone beeps, and Memory nDeleted appears.Go Back — returns you to the list ofmemory numbers.Reviewing Memory NumbersTo review your memory numbers, pressMEM. The list of memory location numbers(1–0) appears with the name stored witheach number (or <Memory n> if you did notstore a name).To see the stored phone numbers, press 7777.Only the first 13 characters/numbers appearfor number. To see the rest of the number,press 7777 when the number is on the display.Press 6666 to return to the name display. To exit the memory number list, press MEM.Note: To view the name and number at thesame time, press SELECT when the cursor isby a memory location number. To exit thisdisplay, hold down DELETE until the displayclears.Dialing a Memory NumberTo dial a number stored in memory, lift thehandset and press MEM. The list of memorylocation numbers appears. Choose a memo-ry location (1–0) by pressing a number or byrepeatedly pressing 8888 or 9999, then pressTALK.You can also dial a memory number afterpressing TALK. Press MEM (the display doesnot change but the phone’s memory recallactivates), then press the desired memory lo-cation number.Chain-Dialing Service NumbersFor quick recall of numbers for special ser-vices (such as bank-by-phone), store eachgroup of numbers in its own memory loca-tion.Dial the service’s main number first. Then, atthe appropriate place in the call, press MEMand enter the number for the location wherethe additional information is stored.Testing Stored Emergency Num-bersIf you store an emergency service’s number(police department, fire department, ambu-lance) and you choose to test the storednumber, make the test call during the lateevening or early morning hours to avoid peakdemand periods. Also, remain on the line toexplain the reason for your call.43-1122.C.fm  Page 15  Wednesday, December 13, 2000  1:56 PM
16 Caller ID OperationˆCaller ID OperationIf you subscribe to Caller ID service fromyour phone company, the phone companysends information about the call, as well asthe time and date, between the first and sec-ond rings of every call you receive. Thephone displays this information after the sec-ond ring, and it stores up to 20 Caller IDrecords for later review. It also shows if thecaller information is unavailable or if thename and number were blocked by the caller(see “Caller ID Messages”).If you subscribe to Call Waiting with CallerID, you hear a tone through the handsetwhen a call comes in, then the Caller IDrecord appears.If the phone’s Caller ID memory becomesfull, any new call replaces the oldest call’srecord.IMPORTANT CALLER ID INFORMATIONTo use the phone’s Caller ID and Caller IDwith Call Waiting features, you must be in anarea where those services are available andyou must subscribe to those servicesthrough your local phone company. Where Caller ID is offered, one or more op-tions are generally available:• caller’s number only• caller’s name only• caller’s name and numberREVIEWING CALLER ID RECORDSIf the handset is face-up on the base, itshows the number of new and total Caller IDrecords and lets you view the display for anynew records.To review the Caller ID records, lift the hand-set and press CALL ID. The number of newCaller ID records, if any, and the total num-ber of records appears. Repeatedly press 9999to scroll through the Caller ID records fromthe newest to the oldest, or 8888 to scroll backthrough the records. To scroll quickly throughthe records, hold down 8888 or 9999. The top line of each record shows the date,time and the number of calls from that num-ber. The second line shows the caller’s name(if available), and the third line shows thecaller’s phone number.Caller ID MessagesDisplay DescriptionNew: XX Total: XXShows the number of new Caller ID records (records you have not reviewed) and the total number of records.Private Name or Private Number The caller has blocked the caller ID information.Unknown Name or Unknown Number The caller is not within a Caller ID service area.Incomplete Data Appears if there was an error during the transmission of Caller ID information. Occa-sional errors are nor-mal. If the phone frequently displays Incomplete Data, con-tact your local tele-phone company or your local RadioShack store.43-1122.C.fm  Page 16  Wednesday, December 13, 2000  1:56 PM
17Caller ID OperationADDING/DELETING THE AREA CODEThe display shows the area code of an in-coming call, unless the call comes from thearea code you stored (see “Storing YourArea Code” on Page 11). You can add thearea code to the display or delete it. With therecord displayed, press 3 to add or delete thearea code.Numbers are stored in memory as they ap-pear on the display, with or without the areacode. Numbers in Caller ID records remainthe same, even if you add or delete the areacode (to make a call, for example).DIALING NUMBERS FROM A CALLER ID RECORDTo dial a local number stored in a Caller IDrecord, recall the record, then press TALK.To add or delete the area code, press 3 be-fore you press TALK.If the call is long distance, press 1 (1 ap-pears before the displayed number) beforeyou press TALK.Note: If a Caller ID record does not contain aphone number (if it was blocked by the caller,for example) you cannot dial from thatrecord.STORING A CALLER ID RECORD IN MEMORYFollow these steps to store the name andnumber from a Caller ID record into a memo-ry location.1. Press  CALL ID then 9999 to recall therecord you want to store. To add ordelete the area code, press 3. If it is along distance number, press 1.2. Press  MEM.  Select Locationappears.3. Choose a memory location (1–0) bypressing a number or by repeatedlypressing 8888 or 9999, then press SELECT.If the selected location is empty, thephone beeps to confirm that it stored thenumber, then the Caller ID recordappears.If a record exists in the selected loca-tion,  Replace Memory? appears,prompting you to confirm the replace-ment. Press 8888 or 9999 to move the cursorto Yes or No, then press SELECT.DELETING CALLER ID RECORDSYou can delete Caller ID records individuallyor all at once.Deleting a Single Caller ID RecordFollow these steps to delete a single CallerID record.1. Press CALL ID then 9999 to recall the recordyou want to delete.2. Press DELETE. Delete Message? ap-pears, prompting you to confirm the deletion.3. Press 8888 to move the cursor to Yes, thenpress SELECT or DELETE. The phone beepsonce, indicating that the record was deleted.Deleting All Caller ID RecordsFollow these steps to delete all Caller IDrecords.1. Press CALL ID so the record totals appear.2. Press DELETE. Delete All? appears,prompting you to confirm the deletion.43-1122.C.fm  Page 17  Wednesday, December 13, 2000  1:56 PM
18 Troubleshooting3. Press 8888 to move the cursor to Yes, thenpress SELECT or DELETE. The phone beeps once and TOTAL:00 appears, indicatingthat all Caller ID records were deleted.ˆTroubleshootingWe do not expect you to have any problems with your phone, but if you do, these suggestionsmight help.Problem SuggestionsThe phone does not work or works poorly.Be sure the base’s phone line cord and AC adapter are correctly and securely connected.Be sure the battery pack in the handset is connected and charged.Return the handset to the base for about 5 seconds to reset the security access-protection code.The display flashes slowly when the hand-set is faceup on the base.Make sure the battery pack in the handset is properly connected.The handset stops working or works poorly during a call.Move the handset closer to the base. Lift the base’s antenna to a fully vertical position. Be sure the handset’s battery pack is charged. (If the battery pack power is too low, the handset cannot display Low Battery.)Low volume or unusual sounds.Someone has picked up another phone on the same line. Hang up the other phone.Your conversation is difficult to hear due to dropout or muting.Keep the handset away from computers, remote control toys, wireless micro-phones, alarm systems, intercoms, room monitors, fluorescent lights, and elec-trical appliances.Move to another location or turn off the source of interference. Press CH to change the channel. Hang up and redial the number.The phone cannot be operated at a useful distance from the base because the signal becomes weak or noisy (handset’s range has decreased).Lift the base’s antenna to a vertical position. Be sure neither the handset’s nor base’s antenna is touching a metal surface. Return the handset to the base and recharge the battery pack.The handset battery pack does not charge.Check the charging contacts on the handset and base. If they are dirty, clean them with a pencil eraser. Be sure the battery pack is connected correctly.Be sure the handset is properly seated on the base. Replace the battery pack.43-1122.C.fm  Page 18  Wednesday, December 13, 2000  1:56 PM
19TroubleshootingIf you still have problems, disconnect the phone. If other phones on the same line work proper-ly, the fault is in this phone or its installation. If you cannot find the problem, take the phone toyour local RadioShack store for assistance.CAREKeep the phone dry; if it gets wet, wipe it dry immediately. Use and store the phone only in nor-mal temperature environments. Handle the phone carefully; do not drop it. Keep the phoneaway from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new.Modifying or tampering with the telephone’s internal components can cause a malfunction andmight invalidate its warranty and void your FCC authorization to operate it. If your telephone isnot performing as it should, take it to your local RadioShack store for assistance. If the troubleis affecting the telephone lines, the phone company can ask you to disconnect your telephoneuntil you have resolved the problem.The handset does not ring or receive a page.Move the handset closer to the base. Lift base’s antenna to a vertical position. Be sure the battery pack in the handset is connected and charged.Move the base away from other electrical devices.You have an incoming call, but do not receive any Caller ID informa-tion.Let the phone ring twice before you answer so the system has time to record the Caller ID information. Check that the system is correctly and securely connected. Check with your phone company to verify that your Caller ID service is active.Problem Suggestions43-1122.C.fm  Page 19  Wednesday, December 13, 2000  1:56 PM
43-1122 UCZZ01308BZ12A00Printed in ChinaCRadioShack CorporationFort Worth, Texas 76102Limited One-Year WarrantyThis product is warranted by RadioShack against manufacturing defects in material and workman-ship under normal use for one (1) year from the date of purchase from RadioShack company-ownedstores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN,RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUD-ING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-ITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINEDHEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANYLIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSSOF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THEPOSSIBILITY OF SUCH DAMAGES.Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-tion of incidental or consequential damages, so the above limitations or exclusions may not apply toyou.In the event of a product defect during the warranty period, take the product and the RadioShacksales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-less otherwise provided by law: (a) correct the defect by product repair without charge for parts andlabor; (b) replace the product with one of the same or similar design; or (c) refund the purchaseprice. All replaced parts and products, and products on which a refund is made, become the prop-erty of RadioShack. New or reconditioned parts and products may be used in the performance ofwarranty service. Repaired or replaced parts and products are warranted for the remainder of theoriginal warranty period. You will be charged for repair or replacement of the product made after theexpiration of the warranty period.This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation ormaintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairsother than those provided by a RadioShack Authorized Service Facility; (c) consumables such asfuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costsof product removal, installation, set-up service adjustment or reinstallation.This warranty gives you specific legal rights, and you may also have other rights which vary fromstate to state.RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102We Service What We Sell12/9943-1122.C.fm  Page 20  Wednesday, December 13, 2000  1:56 PM

Navigation menu