Radiolink Electronic RL039RC6GS Pistol grip transmitter User Manual

Radiolink Electronic Limited Pistol grip transmitter

Manual

RADIOLINK ELETRONIC LIMITEDwww.radiolink.comDigital 6-Channel Proportional RC SystemInstruction ManualCE FCC ROHSTechnical updates and additional programming examples available at: http://www.radiolink.com
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com1INTRODUCTIONThank you for choosing Radiolink 2.4 GHz 6 channels pistol grip radio -- RC6GS.RC6GS is default 6 channels transmitter, sells with receiver R6FG which with gyro integrated and HVservo supported.RC6GS, work with FHSS spread spectrum and 67 channels pseudo frequency sequence hopping, bothtransmitter and receiver use industrial chip ensure superior anti-interference ability both at the samefrequency band and different frequency band and anti-sparks interference ability. Ground controldistance is up to 400 meters.Suggestion: In order to fully enjoy the benefits of this remote control equipment and ensure safety,please read the introduction carefully and set up the device as described below.If you found any problems during the operation process, please refer to the manual. If the problemstill exists, you could contact our dealers to find out the way to solve it. And you could also log in BBS(such as https://www.facebook.com/Radiolink-1455452961436694/www.rcgroups.com) or call our after-sales (+86-0755-88361717) to check the issues related answer.Due to unforeseen changes in production procedures, the information contained in this manual issubject to change without notice.More information please check our website as below:http://www.radiolink.comSupport and Service: It is recommended to have your Radiolink equipment serviced annually duringyour hobby’s “off season” to ensure safe operation.Please be sure to regularly visit the Service and Support web site at www.radiolink.com. This pageincludes extensive programming, use, set up and safety information.Any technical updates and manual corrections will be available on this web pages. If you do not findthe answers to your questions there, please see the end of our contact area for information oncontacting us via email for the most rapid and convenient response.FOR AFTER-SALES SERVICE:Please start here for getting more service.www.radiolink.comPhone:+86-755-88361717Email: after_service@radiolink.com.cn/after_service1@radiolink.com.cnFOR TECHNIQUE SUPPORT:Please start here for answers to technique questions:www.radiolink.comPhone:86-755-88361717Email: alice@radiolink.com.cn
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com2Important Safety Notice：The following two symbols will appear in this manual（please pay attention to the paragraph with thistwo symbols labeled）：Prohibition Testing and confirmationDo not use in bad weather such as rainy or thundering to assure the safety of you and others.Forbid to use this product in the crowd and the place against national law!You need to turn the throttle channel(CH2) and inch switch to the lowest before you use. Thenswitch on the transmitter, finally connect the receiver.The sequence to shut down is that turn off the receiver power first, and then shut down thetransmitter. If the above operations are reverse, it might lead to uncontrolled situation and causeaccidents.The transmitter needs to be powered by 4 AA batteries or 2S-4S LiPo batteries. Please check thevoltage of batteries before using, as it might lead to uncontrolled situation and accidents when thevoltage is lacked. So you must change the battery or recharge them in time.Warning!!!This product is not a toy and is not suitable for children under the age of 18. Adults should keepthe product out of the reach of children and exercise caution when operating this product in thepresence of children.Please don't run in the rain! Rain or moisture may enter the transmitter internal through gaps in theantenna and cause your car to instability even out of control. If inevitable will run in the wet weather(such as game), please be sure to use plastic bags or waterproof cloth to cover your transmitter,please don't run if there is lightning.FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.-- Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions:(1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could voidthe user's authority to operate the equipment.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com3CONTENTS1. Introduction and Service……………………………………………………………………………………………….……………….12. Safety Notice and Warning……………………………………………………………………………………………..……….....….23. Pistol Grip Control System……………………………………………………….....…………………..……………..……….....…..43.1 Transmitter………………………………………………………………………………………………………………..………………43.2 Receiver……………………………………………………………………………………………………………..………………..……63.2.1 Receiver Installation and Binding………………………………………………………………………………………73.2.2 Working Mode…………………………………………………………………………………………….....…………………73.2.3 How to Turn On Gyro Function………………………………………………….…………….…………...……………74. RC6GS Functions…………………………………….………………………….…………………………….………….………..….…...94.1 Display When Power Switch Turned On…………………………………………………………………….……….……...94.2 Language Select "LANGUAGE" ………………....………………………………………….………….……………....…......94.3 Model Select "MODEL"……………………………………………….....……………….…....………........……….…...........104.4 End Point Adjuster "EPA"………………………………….…..…..……………………….…....……......……….………...…104.5 Steering EXP "STEXP"…………………………………….………..……………………….…....………….........…….………..114.6 Steering Speed "STSPD"…………………………………….….……………………….…....……………….….......…..…... 124.7 Throttle EXP "THEXP"……………………………………………………………………….…....…………….………..............124.8 Throttle Speed "THSPD"………………………………………………………………….…....…………….…………............144.9 A.B.S. Function "A.B.S"…………………………………………………..…………………….…....………….…....................164.10 Throttle Acceleration "ACCEL"…………………………………………………………….…....……………….……….....194.11 Idle-Up "IDLUP"………………………………………………………………………………….…....….………........…...........204.12 Sub-trim "SUBTR"………………………………………………………………………….…....………….……..…….............204.13 Servo Reverse "REV"……………………………………………………………………….…....……….…………............….214.14 Steering Dual Rate/Throttle Dual Rate "D/R"…………………………………………….…………………......……224.15 ATL Function "ATL"………………………………………………………………………………….…....…….…...……..........224.16 Programmable Mixes "PMIX"………………………………………………………………….…....….……………...…....234.17 Channel 3 Position "AUX"………………………………………..……………………………….….....……………........…254.18 Model Name "NAME"………………………………………………………………………….…....……….…….….............264.19 Low Voltage Alarm……………………………………………………..……………………….…....……….….………..........264.20 Gyro Sensitivity…………………………………………………………………………………….…....……….……...…..........264.21 Fail Safe………………………………………………………………………………….…………….…............…...…................274.22 Reset Function "RESET"………………………………………………………………………………….……...…................27
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com43. Pistol Grip Control SystemRC6GS, transmitter with chip STM32F103RB, receiver R6FG/R6F with 32 bits industrial chip, 12ms onlyfrom transmitter to the receiver, thus provide control synchronous and performance perfect.The same FHSS spread spectrum and 67 channels pseudo random frequency sequence hopping ofAT9S makes RC6GS have superior anti-interference ability both at the same frequency band anddifferent frequency bands.Control distance is up to 400 meters.3.1 Transmitter
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com5Size: 213 *117 * 115.5mmFrequency: 2.4Ghz ISM Band（2400MHZ-2483.5MHz）Channel: 6 CHChannel resolution: 4096, the regular jitter is 0.5usModel: Cars/BoatsModulation Mode: GFSKSpread Spectrum: FHSS, 67 Channels Pseudo Random Frequency Sequence Hopping10 Modes Memory StorageAntenna Length: 106mmControl Distance: More than 400 meters groundLCD Screen: 128*64 Resolution, LCD Back Light
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com6Transmitter Operating Voltage: 4.8-15.0V DCTransmitter Battery: 4*AA or 2-4S lithium batteryTransmitter operating current : 80-120mARF power: <20dbmLow Voltage alert: Yes(lower than 4.6V), can be set when using 2-4S LiPo batteryReceiver: R6FG, R6F, R8EF, R8FM3.2 ReceiverRC6GS, sells with R6FG, 2.4GHz 6 channels receiver, gyro integrated and HV servo supported.Specification1) Frequency: 2.4GHz ISM band(2400MHz~2483.5MHz)2) Size: 35*20*13mm3) Channel: 64) Model: cars/boats5) Modulation mode: GFSK6) Spread spectrum: FHSS7) Antenna length: 210mm8) Control distance: more than 400 meters9) Power supply: 4.8~10.0V DC10) Channel resolution: 4096, the regular jitter is 0.5us11) Work current: 30mA
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com73.2.1 Receiver Installation and BindingHow to Match Code With Transmitter:1. Put the transmitter and the receiver close to each other within 50 centimeters.2. Turn on the transmitter, then power on the R6FG.3. There is a black button on the R6FG, press the binding button twice in two seconds and release,receiver light start blinking, after about blinking 8 times, match code success then receiver signal LEDalways on!Attention: R6FG default have not turn on the gyro function. Make sure the R6FG keep motionlesswhen power on it, because the R6FG will do the self-test.R6FG with two indicate LED, green LED on indicate normal working mode while both green and redLED on indicate gyro function working mode.3.2.2 Working ModeR6FG has two working modes：normal working mode and gyro function working mode.Normal Working ModeGreen LED, gyro will not working.Gyro Function Working ModeBoth green and red LED on.Receiver with gyro integrated to hold the vehicle in a straight line during aggressive acceleration andbraking or get bumped around by rough terrain.Receiver with gyro integrated to keep the uni-direction and anti-slip.3.2.3 How to Turn On Gyro FunctionQuick press the ID SET switch two times within 1 second, the LED change from green to red meansgyro function has turn on.Gyro Function SetupIntegrated Gyro, is used to assure the stability of cars on turning status; and keep on straight runningeven the cars get some mechanical phantom. Gyro function can be enabled or disabled.A. Gyro enabledGyro preset disabled, and it enters post indication status. There are two indicators on the receiver. Thegreen one shows the receiver status and the red one is for gyro. When the led turns on, the gyro isenabled , and the led turns off, gyro disabled.B. Gyro enabled forwardCars can be drove forward and backward, gyro is enabled forward or backward correspondingly. Likethe EP cars, different connection will make different direction, the gyro is ensured to be enableforward.C. Gyro reverseSame like a plane has reverse, car kit gyro has reverse as well. Only right set reverse gyro can act tocorrect.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com8Setup(1) Enable gyroPress binding key three time (interval less than 1 second), the red LED will flash three time, indicatingwhether gyro is enabled.(2) Gyro sensitivityGyro sensitivity is predefined to adjust by channel three (factory set VR function), turning the VRswitch clockwise to raise sensitivity and anti-clockwise to decrease.(3) Gyro forwardWhen the gyro is enabled, pull the throttle trigger and then release (make sure the car stops running),turn the car right or left without changing steering wheel, if the servo will not follow with, it showsgyro is set backward. Press the binding switch one time less than 1 second, the LED flashes red once,gyro is changed to act forward.(4) Gyro reverseSet the gyro forward, turn the car right or left to see whether gyro functions. The wheel will turn leftwhen the car is turned right and the wheel turns right when the car is turned left. If the gyro actscounter, press the binding switch two time, the LED flashes two time red, the gyro reverse iscorrected.Installment of receiver antenna：(1) The antenna must be kept as straight as possible. Otherwise it will reduce the effective range.(2) Large model aircraft may of some metal part interfering signal; in this case the antennasshould be placed at both sides of the model. Then the best RF signal condition is obtained at anyattitude.(3) The antennas must be kept away from conductive materials, such as metal and carbon by atleast a half inch. The coaxial part of the antennas does not need to follow these guidelines, but do notbend it in a small radius.(4) Keep the antennas away from the motor, ESC, and other noise sources as much as possible.(5) Press and hold the Easy Link (ID SET) one second, now the receiver starts work.(6) After all of the above steps finished, the LED indicator will turn and keep in red/green.(7) The receiver can be packed by sponge or foam for shocking proof when it is installed to themodel.After all of the above steps finished, turn off the transmitter and then power it on, now the programfunctions to assure it under control of transmitter with a right connection.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com94. RC6GS Functions4.1 Display When Power Switch Turned OnLCD ScreenWhen you power on the transmitter RC6GS, LCD screen shows Model Name, Transmitter Name,Battery Voltage, Steering Trim, Throttle Trim.Model NameThe system can store the data for 10 models, model name will show on the LCD when you power onthe transmitter. Please make sure the model name is the right one that you want.If the model name you chose is not corresponding with your model, the settings should be wrong.Battery VoltageIn addition to the model, LCD can show the voltage of battery. When the voltage is lower than 4.6V, itwould start the low-voltage alarm, it would send out “ DDD … ” sounds, till the transmitter ispower-off. When you hear the low-voltage alert, you have no more than 4 minutes for controllingyour model, please safely stop your model before the uncontrolled situation. Please make sure thebattery voltage is higher than this voltage data while radio controlling.Transmitter function menu settingWhen you want to browse or change a setting of transmitter, you should go into function menusetting mode. Under function menu setting mode, you can set up Language. Select "LANGUAGE" ,Model Select "MODEL", End Point Adjuster "EPA", Steering EXP "STEXP", Steering Speed "STSPD",Throttle EXP "THEXP", Throttle Speed "THSPD", A.B.S. Function "A.B.S", Throttle Acceleration "ACCEL",Idle-Up "IDLUP", Sub-trim "SUBTR", Servo Reverse "REV", Steering Dual Rate/Second. Dual Rate "D/R",ATL Function "ATL", Programmable Mixes "PMIX", Auxiliary, Channel 3, 4, 5 and 6 "AUX"，Model name"NAME", Reset function "RESET".4.2 Language Select "LANGUAGE"Both English and Chinese version menu are available for which is convenient for Chinese andEnglish-speaking players to personalize function menus.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com10(1) Access the function menu (By pressing “ Exit ” and“ Enter”buttons simultaneously and holding them down forone second), the Language select function will be chosen.(2) Press “Enter” button to get into “LANGUAGE” functioninterface.(3) Use“Dec(-)”or “Inc(+)”key to select “中文”or “English”,the selected language will be with black shading effect.(4) Press “Enter” button, the desired language is selected, andreturn to the initial screen automatically.4.3 Model Select "MODEL"RC6GS can store model memories for ten models. Use this function to call a new model.(1) Access the function menu (By pressing “Exit” and“Enter”buttons simultaneously and holding them down for one second),press“Enter”key once, the Model select function will be chosen.(2) Press “ Enter ” button, the current active model will beblinking.(3) To activate a different model by pressing “Dec(-)” or “Inc(+)”button until the desired model blinks.(4) Press “Enter” button, the selected model stops blinking, nowthe model has been selected.(5) Return to the initial screen by pressing “Exit” button twice.4.4 End Point Adjuster "EPA"Use EPA when performing left and right steering angle adjustments, throttle high side/brake sideoperation amount adjustment, and channel 3 servo up side/down side operation amount adjustmentduring linkage.Correct the maximum steering angle and left and right steering angles when there is a difference inthe turning radius due to the characteristics, etc. of the vehicle.Setting item (channel and direction)ST :Steering (left/right)TH: Throttle (forward/brake)CH3: 3rd channel (left/ right)CH4: 4th channel (left/ right)CH5: 5th channel (left/ right)CH6: 6th channel (left/ right)Steering EPA Throttle EPAST:0%~120%(left/ right) TH:0%~120%(forward/brake)Initial value:100% Initial value : 100%
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com11Aux Servo EPA Aux Servo EPACH3:0%~120%(left/ right) CH4:0%~120%(left/ right)Initial value: 100% Initial value: 100%Aux Servo EPA Aux Servo EPACH5:0%~120%(left/ right) CH6:0%~120%(left/ right)Initial value: 100% Initial value: 100%End point adjustment(1) Access the function menu (By pressing “Exit” and “Enter” buttons simultaneously and holdingthem down for one second),press “Inc(+)” button twice to chose EAP function.(2) Press “Enter” button to get into EPA function interface, use “Dec(-)” or “Inc(+)” button toselect the desired setting item , press “Enter” key, the initial value of your selected setting item willblink, then you can press “Dec(-)” or “Inc(+)” button to adjust the value of your selected settingitem.(Note: In the interface of adjusting the value, return to the initial value "100%" by pressing “Dec(-)”and “Inc(+)” buttons simultaneously for about 1 second.)3. Press “Enter” button, the adjusted value of your selected setting item stops blinking, now thevalue of your selected setting item has been set.4. Return to the initial screen by pressing “Exit” button twice.4.5 Steering EXP "STEXP"This function is used to change the sensitivity of the steering servo around the neutral and both endsposition. It has no effect on the maximum servo travel.Adjust the sensitivity of direction wheel both in neutral position and ends.Setup ItemRATE: Steering EXP rateAdjustment range-100%~0%~+100%Initial value: 0%0%~-100%: Sensitivity around neutral position is low,getting higher when approaching ends.0%: Sensitivity around the neutral and ends position is equal0%~+100%: Sensitivity around neutral position is high, getting lower when approaching endsSteering operation curve adjustment(1) Access the function menu (By pressing “Exit” and “Enter ”buttons simultaneously and holdingthem down for one second ), press “Inc(+)” button three times to chose EAP function.(2) Press “Enter” button to get into STEXP function interface, press “Enter”key and the initial value
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com12of the rate will blink, then you can press“Dec(-) ”or“Inc(+)”button to adjust the value and the curveof the rate shown in the figure will change correspondingly.(Note: In the interface of adjusting the value, return to the initial value "0%" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)(3) Press “Enter” button, the adjusted value of the rate stops blinking, now the value of the rate hasbeen set.(4) Return to the initial screen by pressing“Exit” button twice.Note: the Vertical cursor shown in the figure moves in step with steering wheel operation.4.6 Steering Speed "STSPD"Quick steering operation will cause momentary under steering,loss of speed, or spinning. This function is effective in suchcases.Setup itemTURN: turn directionRETURN: return back to the original directionAdjustment range0%~100% (each direction)At 100%, there is no delaySteering servo delay(1) Access the function menu (By pressing “Exit” and “Enter” buttons simultaneously and holdingthem down for one second), press “Inc(+)” button four times to chose STSPD function.(2) Press“Enter” button to get into STSPD function interface, press “Dec(-)” or“Inc(+)” buttonto select setup item, then press “Enter” key and the initial value of selected setup item will blink.(3) Use“Dec(-)” or “Inc(+)” button to adjust the value of the selected setup item.(Note : In the interface of adjusting the value, return to the initial value "100%" by pressing“Dec(-)”and“Inc(+)” buttons simultaneously for about 1 second.)(4) Press “Enter”button, the adjusted value of the selected setup item stops blinking, now the valueof the selected setup item has been set.(5) Return to the initial screen by pressing “Exit” button twice.4.7 Throttle EXP "THEXP"This function makes the throttle high side and brake side direction servo operation quicker or milder.It has no effect on the servo maximum operation amount. For the high side, selection from amongthree kinds of curves (CRV/VTR/EXP) is also possible.The curve can be divided into: Five dots throttle curve adjustment, Single point adjustment,Exponential curve adjustment, Braking index curve adjustment. To elevation point,we can select(Exponential curve/Single point curve/Five points curve).
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com13Curve point adjustment(select five points 1-5)(1) Press"Enter" button,The curve point value start flashing,then press"Dec(-)"and"Inc(+)" button toadjust the starting value.(2) Press "Enter" button ,starting value stop flashing,adjustment is completed.(3) Press "Exit" button for two times,back to the initial interface.Throttle curve adjustmentAdjustment method for CRV curveSetup ItemsMode: ON/OFFRATE: 0%~100%1. Enter the function menu and use“ Dec(-) ” or “ Inc(+) ”button to access THEXP function. Select “ FWD-CRV ”function.2. Press “Dec(-)” or “Inc(+)” button to select curve points 1~5 for curve point adjustment that youwant, from the graph you will clearly see the changes you have made.Adjustment method for VTR curveAdjustment rangeTG.P: 20-80RATE: -100~0~+1001.Enter the function menu and use “Dec(-)” or“Inc(+)”buttonto access THEXP function. Select“FWD-VTR” function.2.Press “Dec(-)” or “Inc(+)” button to select RATE for forwardside adjustment that you want, when the “ MODE ” value is“OFF” the VTR will not work, only the “MODE” value set to“ON” the VTR function is available. From the graph you willclearly see the changes you have made on TG.P and RATE.Adjustment method for EXP curveSetup itemsMODE: EXP turn on or turn offRATE: EXP rateAdjustment rangeMODEL: OFF/ONRATE: -100 ~ 0 ~ +1001. Enter the function menu and use “Dec(-)”or“Inc(+)”buttonto access THEXP function, then select the “FWD-EXP” function.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com142. Press “Dec(-)” or “Inc(+)” button to select RATE for adjustment, set the most comfortable valueyou want. From the graph you will clearly see the changes you have made on the EXP RATE, also movethe trigger to check the throttle status.Adjustment method for BRK-EXP curveSetup ItemsRATE: BRK-EXP rateAdjustment rangeRATE: -100 ~ 0 ~ +1000~-100: flat braking0: uniform braking0~+100: sensitive brakingBrake side adjustment (select BRK)(1) Press“Enter”key, the current BRK value will blink, use“Inc(+)”button to adjust the + side whenyou want to quicker the rise and use“Dec(-)” button to adjust the - side when you want to make therise milder.(Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)(2) Press “Enter” button, the adjusted BRK value stops blinking, now the BRK value has been set.(3) When ending setting, return to the initial screen by pressing “Exit” button twice.4.8 Throttle Speed "THSPD"Throttle servo delaySudden trigger operation on a slippery road only causes thewheels to spin and the vehicle cannot accelerate smoothly. Settingthe throttle speed function reduces wasteful battery consumptionwhile at the same time permitting smooth, enjoyable operation.OperationThrottle servo(amp )operation is delayed so that the drive wheelswill not spin even if the throttle trigger is operated more thannecessary. This delay function is not performed when the throttletrigger is returned and at brake operation.OFF: Speed1 or speed2 can be selected.OFF means shut down the throttle speed functionAdjustment method for SPEED1Setup itemsMODE: Speed type selectionALL: Speed adjustment
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com15Adjustment range0~100 (each direction)At 100, there is no delay(1) Enter the function menu and use “Dec(-)”or“Inc(+) ” button to access THSPD function.(2) Press “Enter” button to get into THSPD function interface.(3) If initial MODE setup item is SPEED1, {if initial MODE setup item is SPEED2 or OFF, you need toselect SPEED1 by pressing“Dec(-)”or“Inc(+)”button to select MODE setup item , then press“Enter”key, SPEED2 or OFF will blink, press “Dec(-)” or “Inc(+)” button, when the blinking SPEED 2 or OFFchange to blinking SPEED 1, press“Enter” key, SPEED1 will stop blink, now SPEED1 is selected}, press“Dec(-)” or “Inc(+)” button to select ALL setup item, then press“Enter” key, the initial value willblink, use“Dec(-)”or“Inc(+)” button to adjust the delay of the entire throttle forward side range.(Note: In the interface of adjusting the value, return to the initial value "100" by pressing “Dec(-)”and “Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set.(4) When ending setting, return to the initial screen by pressing “Exit” button twice.Adjustment method for SPEED2Setup itemsMODE: Speed type selectionLOW: Low side range speed adjustmentHIGH: High side range speed adjustmentTGP1: Low and medium speed switching pointAdjustment rangeLOW: 0~100HIGH: 0~100At 100, there is no delayTGP1: 0~100(1) Enter the function menu and use “Dec(-)”or “Inc(+) ” button to access THSPD function.(2) Press “Enter” button to get into THSPD function interface.(3) If initial MODE setup item is SPEED 2,{ if initial MODE setup item is SPEED 1, you need to selectSPEED2 by pressing “Dec(-)” or “Inc(+)” button to select MODE setup item, then press “Enter”key, SPEED1 or OFF will blink, press “Dec(-)” or “Inc(+)” button, when the blinking SPEED1 or OFFchange to blinking SPEED2, press “Enter” key, SPEED2 will stop blinking, now SPEED2 is selected},press“Dec(-)”or“Inc(+)”button to select "LOW" or "HIGH" delay adjustment or“TGP1”speedswitching point adjustment.(4) Press “Enter” key to confirm "LOW" or "HIGH" or “TGP1” setup item, and the value of yourselected setup item will blink. Use “Dec(-)” or “Inc(+)” button to adjust the value.(Note: In the interface of adjusting the value, return to the initial value (the initial value of LOW andHIGH is “100”, the initial value of TGP1 is “30”) by pressing “Dec(-)” and “Inc(+)” buttons
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com16simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now your selected value has been set.(5) When ending setting, return to the initial screen by pressing “Exit” button twice.4.9 A.B.S. Function "A.B.S"Pulse brakeWhen the brakes are applied while cornering with a 4 Wheel Drive or other type of vehicle,under-steer may occur. The generation of under-steer can be eliminated and corners can be smoothlycleared by using this function.Operation- When the brakes are applied, the throttle servo will pulse intermittently. This will have the sameeffect as pumping the brakes in a full size car.- The brake return amount, pulse cycle, and brake duty can be adjusted.- The region over which the ABS is effective can be set ac-cording to the steering operation. (Mixingfunction)Setup itemsABP: Brake return amountDLY: Delay amountCYC: Cycle speedTGP: Operation pointDTY: Cycle duty ratioSTM: Steering mixing-ABP(Amount of brake return): Sets the rate at which the servo returns versus trigger operation forbrake release. When set to 0, the ABS function is notPerformed. When set to 50, the servo returns 50% (1/2)of the trigger operation amount and when setto 100, the servo returns to the neutral position.-DLY(Delay): Sets the delay from brake operation to ABS operation. When set to 0, the ABS function isactivated without any delay. At 50%, the ABS function is activated after a delay of approximately 0.7second and at 100, the ABS function is activated after a delay of approximately 1.4 seconds.-CYC(Pulse speed): Sets the pulse speed (cycle). The smaller the set value, the faster the pulse cycle.- TGP(Trigger point): Sets the trigger point at which the ABS function begins to operate at brakeoperation.-DTY(Cycle duty ratio): Sets the proportion of the time the brakes are applied and the time the brakesare released by pulse operation. The ratio can be set to +3 ~ 0~-3 in 7steps.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com17- STM(Steering mixing): Sets ABS operation ON/OFF according to the steering operation range.A.B.S function adjustmentEnter the function menu and use “Dec(-)” or “Inc(+)” button to access A.B.S function, then press“Enter” button to get into A.B.S function interface.(1) Brake return amount adjustmentSelect the setting item "ABP" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” keyand the initial value of “ABP” will blink. Use “Dec(-)”or“Inc(+)”button to adjust the return amount.(Note: In the interface of adjusting the value, return to the initial value "50" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set."0": No return"50": Return to the 50% position of the brake operation amount"100": Return to the neutral position.Brake return amount (ABP)0 ~ 50 ~ 100Initial value: 50- Brake return amount (ABP) is influenced by the "EXP" rate on the brake side.(2) Delay amount setupSelect the setting item "DLY" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” keyand the initial value of “DLY” will blink. Use “Dec(-)”or “Inc(+)”button to adjust the delay amount.(Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set."0": A.B.S. function performed without any delay"50": A.B.S function performed after an approximate 0.7 sec delay"100": A.B.S. function performed after an approximate 1.7 secs delayDelay amount (DLY)0 ~ 100Initial value; 0(3) Pulse speed adjustmentSelect setting item "CYC" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” key andthe initial value of“CYC”will blink. Use“Dec(-)”or“Inc(+)”button to adjust the pulse speed (cycle).(Note: In the interface of adjusting the value, return to the initial value "5" by pressing“Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com18- The smaller the set value, the faster the pulse speed.Cycle speed (CYC)0 ~ 30Initial value: 5(4) Operation point setupSelect setting item "TGP" by pressing “Dec(-)” or “Inc(+)” button, then press “Enter” key andthe initial value of “TGP” will blink. Use “Dec(-)” or “Inc(+)”button to adjust the operation point.(Note: In the interface of adjusting the value, return to the initial value "30" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set.- Sets the throttle trigger position at which the A.B.S. function is performed. The number is the 100display with the full brake position made 100%.Operation point (TGP)0 ~ 100Initial value: 30(5) Cycle duty ratio setupSelect setting item "DTY" by pressing “Dec(-)” or “Inc(+)” button, then press“Enter” key and theinitial value of “DTY” will blink. Use “Dec(-)” or “Inc(+)”button to adjust the duty ratio.(Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set."-3": Brake application time becomes shortest. (Brakes lock with difficulty)"+3": Brake application time becomes longest (Brakes lock easily)(Remark) For low grip set at the - side and for high grip set at the + side.Duty ratio (DTY)-3 ~ 0 ~ +3Initial value: 0(6) Steering mixing setupSelect setting item "STM" by pressing“Dec(-)”or“Inc(+)”button, then press“Enter” key and theinitial value of “STM”will blink. Use “Dec(-)”or “Inc(+)”button to adjust the steering mixing range.(Note: In the interface of adjusting the value, return to the initial value "OFF" by pressing “Dec(-)”and “Inc(+)” buttons simultaneously for about 1 second.)Press“Enter”button, the adjusted value stops blinking, now the value has been set.-Sets the range within which the A.B.S. function is performed relative to steering wheel operation.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com19Steering mixing (STM)OFF, N10 ~ N100, E10 ~ E100Initial value: OFFWhen steering mixing is set and steering operation enters the set range, "*" is displayed in front ofthe number. When mixing is OFF, the A.B.S function can operate over the entire steering range.When ending setting, return to the initial screen by pressing “Exit” button twice.4.10 Throttle Acceleration "ACCEL"Function which adjusts the movement characteristic from the throttle neutral position.The servo will jump to the input position at its maximum possible speed. Unlike exponential, whichadjusts the whole throttle movement into a curve, throttle acceleration simply "jumps" away fromneutral and then leaves the remaining response linear.Setup itemFWRD: Forward side acceleration amountBRAK: Brake side acceleration amountThrottle acceleration adjustmentEnter the function menu and use “Dec(-)” or “Inc(+)” buttonto access ACCEL function, then press “Enter” button to get intoACCEL function interface.(1) Forward acceleration amount adjustmentPress “Dec(-)” or “Inc(+)” button to select “FWRD”, press“Enter”key to confirm and the initialvalue of “FWRD” will blink, then use “Dec(-)”or“Inc(+)” button adjust the acceleration amount.(Note: In the interface of adjusting the value, return to the initial value "0%" by pressing “Dec(-)”and “Inc(+)” buttons simultaneously for about 1 second.)Press“Enter”button, the adjusted value stops blinking, now the value has been set."0%": No acceleration"100%": Maximum acceleration(Approximately1/2of the forward side steering angle)Forward acceleration amount(FWRD)0%~100%
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com20Initial value: 0%(2) Brake side acceleration amount adjustmentPress “Dec(-)” or “Inc(+)” button to select “ BRAK ”, press“Enter”key to confirm andthe initial value of “BRAK” will blink, then use“Dec(-)”or“Inc(+)”button adjust the accelerationamount.(Note: In the interface of adjusting the value, return to the initial value"0%" by pressing“Dec(-)” and “Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set."0%": No acceleration"100%": Maximum acceleration (Brake side maximum steering angle)Brake side acceleration amount(BRAK)0%~100%Initial value: 0%When ending setting, return to the initial screen by pressing “Exit” button twice.4.11 Idle-Up "IDLUP"Idle up at engine startUse this function to improve the starting characteristics of the engine by raising the idling speedwhen starting the engine of a gas powered car.Idle-Up rate (RATE)-50% ~ -1%, 0%, +1% ~ +50%Initial value: 0%"-": Brake side"+": Forward sideIdle-Up "IDLUP"(1) Enter the function menu and use “Dec(-)” or“Inc(+) ”button to access IDLUP function.(2) Press “Enter” button to get into IDLUP function interface.(3) Press “Enter” key, and the initial value of RATE will blink. Use“ Dec(-) ” or “Inc(+)” buttonto adjust the value.(Note: In the interface of adjusting the value, return to the initial value "0%" by pressing “Dec(-)”and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter”button, the adjusted value stops blinking, now the value has been set.(4) When ending setting, return to the initial screen by pressing “Exit”button twice.4.12 Sub-trim "SUBTR"Servo center position adjustmentUse this function to adjust the neutral position of the steering, throttle and channel 3 servos.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com21ChannelST: Steering(CH1)TH: Throttle(CH2)CH3: Channel3(VR)CH4: Channel4(SWA)CH5: Channel5(SWB)CH6: Channel6(SWC)Sub-trimST: -100~0~+100TH: -100~0~+100CH3: -100~0~+100CH4: -100~0~+100CH5: -100~0~+100CH6: -100~0~+100Initial value : 0(1) Enter the function menu and use “Dec(-)”or “Inc(+)” button to access SUBTR function.(2) Press “Enter” button to get into SUBTR function interface.(3) Use “Dec(-)” or “Inc(+)” button to select ST channel, press “Enter”key, and the initial valueof ST will blink. Use “Dec(-)” or “Inc(+)” button to adjust the center.(Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)(4) Press “Enter” key, the adjusted value stops blinking, now the center of ST has been adjusted.(5) TH channel and CH3 can be set similarly.(6) When ending setting, return to the initial screen by pressing “Exit” button twice.4.13 Servo Reverse "REV"Servo operation reversingThis function reverses the direction of operation of the servos related to transmitter steering, throttle,channel 3, channel 4, channel 5 and channel 6 operation.ChannelST: Steering(CH1)TH: Throttle(CH2)CH3: Channel3(VR)CH4: Channel4(SWA)CH5: Channel5(SWB)CH6: Channel6(SWC)
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com22(1) Enter the function menu and use “Dec(-)” or“Inc(+)” button to access REV function.(2) Press “Enter” button to get into REV function interface.(3) Use “Dec(-)” or “Inc(+)” button to select ST channel, press “Enter”key, and the “NOR” willblink.(4) Press “Enter” key, the “NOR” stops blinking, Use “Dec(-)”or“Inc(+)”button to reverse theST servo operation direction.(5) TH channel, CH3, CH4, CH5 and CH6 can be set similarly.(6) When ending setting, return to the initial screen by pressing “Exit” button twice.4.14 Steering Dual Rate/Throttle Dual Rate "D/R"Dual rateThe steering left and right servo travels are adjusted simultaneously. When you want to increase theservo travel, adjust the + side. When you want to decrease the servo travel, adjust the - side.Setup ItemSteering D/RThrottle D/RRATESteering D/R rate (RATE)0%~100%Initial value: 100%Throttle D/R rate (Throttle D/R RATE)0%~100%Initial value: 100%(1) Enter the function menu and use “Dec(-)” or “Inc(+)” button to access D/R function.(2) Press“Enter” button to get into D/R function interface.(3) Use “Dec(-)” or “Inc(+)” button to select Steering D/R RATE, press “Enter”key, and the initialvalue of Steering D/R RATE will blink. Use“Dec(-)”or “Inc(+)” button to make adjustments.(Note: In the interface of adjusting the value, return to the initial value"100%" by pressing“Dec(-)”and “Inc(+)” buttons simultaneously for about 1 second.)(4) Press “Enter” key, the adjusted value stops blinking, now the steering D/R RATE has been set.(5) Throttle D/R RATE can be set similarly.(6) When ending setting,return to the initial screen by pressing “Exit” button twice.4.15 ATL Function "ATL"Brake side adjustmentThis function decreases the set value when the braking effect is strong and increases the set valuewhen the braking effect is weak.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com23Setup ItemRATE: Brake amountBrake amount (RATE)0%~100%Initial value: 100%(1) Enter the function menu and use “Dec(-)” or “Inc(+)”buttonto access ATL function.(2) Press “Enter” button to get into ATL function interface.(3) Press “Enter” key, and the initial value of RATE will blink. Use“Dec(-)”or“Inc(+)” button to adjust the value.(Note: In the interface of adjusting the value, return to the initial value "100%" by pressing “Dec(-)”and “Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” button, the adjusted value stops blinking, now the value has been set.(4) When ending setting, return to the initial screen by pressing“Exit” button twice.4.16 Programmable Mixes "PMIX"Programmable mixes between arbitrary channelsThese functions allow you to apply mixing between the steering, throttle, CH3, CH4, CH5 and CH6.Setup itemsLEFT: Mixing rate (Left side)RGHT: Mixing rate (Right side)MST: Master channelSLV: Slave channelProgrammable Mixes "PMIX"MXMD:Mix modeEnter the function menu and use“Dec(-)”or “Inc(+)” button to access PMIX function, then press“Enter” button to get into PMIX function interface.(1) Master channelChannel selection (MST)ST, TH, CH3, CH4, CH5, CH6Initial value: STSelect setup item"MST" by pressing “Dec(-)” or“Inc(+)”button, press“ Enter ” button, the initialmaster channel will blink. Use“ Dec(-)”or“ Inc(+) ” button to select the master channel you wishto adjust, press“Enter” button,the blinking master channel you selected will stop blinking.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com24(2) Slave channelChannel selection (SLV)ST, TH, CH3, CH4, CH5, CH6Initial value: STSelect setup item "SLV" by pressing “Dec(-)” or “Inc(+)” button, press “Enter” button, the initialslave channel will blink. Use“Dec(-)”or“Inc(+)”button to select the slave channel you wish to adjust,press “Enter” button, the blinking slave channel you selected will stop blinking.(3) Left, forward or up side mixing amount adjustmentMixing amount-100~0~+100Select the setting item "LEFT", "FWRD", or "UP"(These setup items are different depend on the masterchannel. ST: "LEFT"; TH: "FWRD"; CH3:"UP") by pressing “Dec(-)” or “Inc(+)” button. Press “Enter”key, the initial value of "LEFT", "FWRD", or "UP" will blink, Use“Dec(-)”or“Inc(+)”button to adjustthe left, forward, or up side mixing amount.(Note: In the interface of adjusting the value, return to the initial value "0" by pressing“Dec(-)”and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” key, the adjusted value stops blinking, the selected mixing amount has been adjusted.(4) Right, brake or down side mixing amount adjustmentMixing amount-100~0~+100Select the setting item "RGHT", "BRAK", or "DOWN"(These setup items are different depend on themaster channel.ST:"RGHT"; TH:"BRAK";CH3:"DOWN") by pressing“Dec(-)”or“Inc(+)”button. Press“Enter”key,the initial value of "RGHT", "BRAK", or "DOWN" will blink, Use“Dec(-)”or“Inc(+)”buttonto adjust the right, brake, or down side mixing amount.(Note: In the interface of adjusting the value, return to the initial value "0" by pressing “Dec(-)” and“Inc(+)” buttons simultaneously for about 1 second.)Press “Enter” key, the adjusted value stops blinking, the selected mixing amount has been adjusted.(5) Mixing mode setupMixing mode (MXMD)OFF, MIXInitial value: OFFSelect setup item"MXMD"by pressing“Dec(-)”or “Inc(+)” button, press “Enter “ button, the initialmixing mode“OFF”will blink. Press“Dec(-)”or “Inc(+)”button to switch “OFF” to “MIX”, press“Enter” button, the blinking “MIX” will stop blinking."OFF": Mixing proportional to master channel operation."MIX": Mixing by master channel another function considered.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com25(6) When ending setting, return to the initial screen by pressing “Exit” button twice.4.17 Channel 3 Position "AUX"The channel 3 and channel 4 servo position can be set from the transmitter. When CH3 is assigned tothe 3rd channel key, this setting is linked to the key. When CH3 and CH4 is not assigned to the 3rdchannel key, it can be set with this screen.You can also set the CH3, CH4, CH5 and CH6 as VR at the same time, or SW.Channel 3 position (POSI)SW(LOCK) or VR(RATE)Channel 4 position (POSI)SW(LOCK) or VR(RATE)Channel 5 position (POSI)SW(LOCK) or VR(RATE)Channel 6 position (POSI)SW(LOCK) or VR(RATE)(1) Enter the function menu and use “Dec(-)” or “Inc(+)” button to access AUX function.(2) Press “Enter” button to get into CH3, CH4, CH5 or CH6 function interface.(3) Use “Dec(-)” or “Inc(+)” button to select Channel setup item.Use “Dec(-)” or “Inc(+)” button to select POSI, press“Enter”key and the value will blink, use“Dec(-)” or “Inc(+)” button to select “VR” or “SW”.Press “Enter” button, the adjusted value stops blinking, now the value has been set.If you use RC6GS to control RCcrawler, you can setup each channelsas below.CH1 is rudder,CH2 is throttle,CH3 can setup to control thetransfer case,CH4 can setup to control the shiftgear,CH5 can setup to control thefront locker andCH6 can setup to control the rear.
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com264.18 Model Name "NAME"RC6GS stores model memories for ten models. Each model memory can be named separatelyaccording to user’s requirement.Factory default name: MODEL1(1) Enter the function menu and use “Dec(-)” or “Inc(+)”button to access NAME function.(2) Press “Enter” button to get into NAME function interface,the first character of current name will blink, and the blinkingcharacter can be reset. The common use characters appear atthe bottom of the screen, use “Dec(-)” or “Inc(+)” button tochoose the character you desired.Press“Enter” button again,the next character of current name will blink. Reset othercharacters of current name in same manner.(3) After accomplishment of naming, all characters of current name will stop blinking, the new namewill be stored automatically.(4) When ending setting,return to the initial screen by pressing“Exit”button twice.(the new settingmodel name will appear on the initial screen)4.19 Low Voltage AlarmThe transmitter’s low voltage alarm adjustable, it depends on what kind of battery, the 4.6V is maycause the battery over discharge and damage the battery. Soyou can set transmitter’s warning voltage when you usedifferent battery.There are four options you can choose:Li2S-7.4VLi3-11.1VNi4S-4.6VALARM: adjustable 4.0V to 16.0VThe car will be out of control if the battery runs out, pleaseimmediately stop running when the alarm starting to ring.4.20 Gyro SensitivityThis function is available to set gyro sensitivity and VR mixing ONor OFF.When MIX set OFF, gyro is disabled while when MIX set ON, youcan adjust gyro sensitivity STD or VR. STD is adjusted on screenand VR is default CH3.In normal mode (STD), range of sensitivity is 0%-100%.(1) Enter the menu, use Dec(-) and Inc(+) to select options forgyro sensitivity.(2) Press the key button “Enter” to enter sub-menu gyro
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com27sensitivity.(3) Press “Enter” again, the initial value will start flashing, then use Dec (-) and Inc (+) to change thevalue.(4) Press the button key “Enter”, the value stops flashing, the setting is finished now.(5) "Mode"and "Rate" can also be set by the same step.(6) Press button key “Exit” to be back to initial screen.4.21 Fail SafeThis function is set by servo, throttle, CH3, CH4, CH5 and CH6.Option:ST: Steering(CH1)TH: Throttle(CH2)CH3: Channel3(VR)CH4: Channel4(SWA)CH5: Channel5(SWB)CH6: Channel6(SWC)RANGE:Servo: -100~+100Throttle: -100~+100CH3: -100~+100CH4: -100~+100CH5: -100~+100CH6: -100~+100Initial value: 0(1) Enter the menu, use “Dec (-)” and “Inc (+)” to select options to set.(2) Press the button key “Enter” to enter menu.(3) Use “Dec (-)” and “Inc (+)” to select SERVO, then press “Enter”. Now the initial valueof SERVO will start flashing, use handle to change the value.(4) Press the button key “Enter”, the value stops flashing, now the value of SERVO is set.(5) THROTTLE is to set by the trigger.CH3 is to set by VR controller.CH4 is to set by the button switch.CH5 is to set by the toggle switch.CH6 is to set by the toggle switch.(6) Press “Exit” two times to back to initial screen.4.22 Reset Function "RESET"RESET- Data reset function:All the data for any model memory can be reset to original factory defaults. Often this function is
RADIOLINK ELETRONIC LIMITEDwww.radiolink.com28done to get a “fresh start” and clear the memory before inputting new model settings.(1) Enter the function menu and use “Dec(-)” or “Inc(+)”button to access RESET function.(2) Press “Enter” button to get into RESET function interface,the symbol “YES” will blink.Be sure to resetPress “Enter” key, the symbol “YES” will stop blinking, andreturn to the initial screen. Now the model data is reset to theinitial setting that is the default value set at the factory.Not to resetPress “Dec(-)” or “Inc(+)” button, the symbol “YES” will stopblinking and the symbol “NO” will blink, press “Enter” key, the symbol “NO” will stop blinking,return to the initial screen by pressing “Exit” button twice.Or you can press “Exit” button twice to quit resetting directly.CAUTION: Resetting the current model memory will permanently erase ALL programminginformation for that model. The data cannot be recovered. Do not reset the model unless you arecertain you want to clear-out that memory and start from scratch.Thank you again for using our product, we hope it can bring you happiness!

Navigation menu