Rajant RJ1302 Mini PCI Radio Module, 1x1,IEEE 802.11 b/g /n,902 MHz User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3223110
Application ID	ySYNvIfhNS/TKnCDs84fQw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.93kB (436620 bits)
Date Submitted	2016-12-09 00:00:00
Date Available	2017-06-08 00:00:00
Creation Date	2016-09-28 13:11:02
Producing Software	Microsoft® Word 2010
Document Lastmod	2016-09-28 13:11:02
Document Title	Users Manual
Document Creator	Microsoft® Word 2010
Document Author:	Toshiba

RJ-1302 USER MANUAL
MODEL
RJ-1302
BRAND
VIZMONET
FCCID
VJA-RJ1302
ICID
7382A-RJ1302
RJ-1302 is an IEEE 802.11b/g/n 902 MHz ~ 928 MHz Radio platform engineered for carrier class long range high
data capacity applications. With superior TX power efficient RF design, the product supports high TX Power
offering best-in class EVM performance at higher modulation schemes. This facilitates to achieve long range
without compromising on data throughput. With well-engineered RX Design, RJ-1302 offers ultra-low receive
sensitivity to achieve long range.
This module shall be integrated into OEM Wireless Products such as Outdoor Access Points and Mesh
networking devices etc., which are typically used at a distance of more than 20 cm away from human body.
INSTALLATION INSTRUCTIONS
1.
2.
3.
Ensure that the Power is shut down before integrating the Module into the host system
Ensure that the antenna port is connected to the antenna that is designated to be used with this
module
Follow appropriate ESD precautionary measures
TECHNICAL SPECIFICATION
RADIO MODULE – GENERAL INFO
Chipset Info
Operating Frequency Range
Security
Data Rates
Legacy 11g up to 54 Mbps
11n HT20-1S up to 65 Mbps
Atheros AR9223-AC1A
902 MHz ~ 928 MHz
WPA, WPA2, AES-CCM & TKIP Encryption, 802.1x, 64/128/152bit WEP
6Mbps, 9Mbps, 12Mbps, 24Mbps, 36Mbps, 48Mbps,54Mbps
(Legacy IEEE802.11g)
1 Mbps,2 Mbps,5.5 Mbps,11 Mbps (Legacy IEEE 802.11b)
MCS0,MCS1,MCS2,MCS3,MCS4,MCS5,MCS6,MCS7 –IEEE 802.11n HT20
Single Stream
Channel Bandwidth
5 MHz/10 MHz/20 MHz
INTERFACE SPECIFICATIONS
Interface
Operating Voltage
RF Antenna connector
PCI 32 bit,33 MHz, mini PCI Form Factor
3.3V
Single MMCX, VERTICAL
OPERATING CENTRE FREQUENCY MAPING
OP FREQ
(MHz)
907
CH BW
(MHz)
5/10
STANDARD
11g/n
Vizmonet Pte Ltd
www.vizmonet.com
912
917
922
5/10/20
5/10/20
5/10
11b/g/n
11b/g/n
11g/n
MECHANICAL DIMENSIONS
Vizmonet Pte Ltd
www.vizmonet.com
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This module is intended for OEM integrator. The
OEM integrator is still responsible for the FCC compliance requirement of the end product, which
integrates this module.
This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
Vizmonet Pte Ltd
www.vizmonet.com

The transmitter module may not be co-located with any other transmitter or antenna,
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the
FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such
that 20 cm may be maintained between the antenna and users.
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: VJA-RJ1302 and IC ID : 7382A-RJ1302”
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as shown in
this manual.
Industry Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device. Le présent
appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and
compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5
de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne sur l'exposition et la conformité de rf.
Vizmonet Pte Ltd
www.vizmonet.com
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne
fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être
installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
This radio transmitter (identify the device by certification number, or model number if Category II)
has been approved by Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif
par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a
été approuvé par Industrie Canada pour fonctionner avec les types d'antenneénumérés ci-dessous et
ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types
d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
The final end product must be labelled in a visible area with the following: The Industry Canada
certification label of a module shall be clearly visible at all times when installed in the host device,
otherwise the host device must be labelled to display the Industry Canada certification number of the
module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar
wording expressing the same meaning, as follows: Contains transmitter module IC: 7382A-RJ1301 This
End equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body. Cet équipement devrait être installé et actionné avec une
distance minimum de 20 centimètres entre le radiateur et votre corps.
Manual Information to the End User
Vizmonet Pte Ltd
www.vizmonet.com
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as show in
this manual.
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final sur la
façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui
intègre ce module.
Vizmonet Pte Ltd
www.vizmonet.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 6
Language                        : en-SG
Tagged PDF                      : Yes
Author                          : Toshiba
Creator                         : Microsoft® Word 2010
Create Date                     : 2016:09:28 13:11:02+08:00
Modify Date                     : 2016:09:28 13:11:02+08:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools