Ranger Electronic Communications 310-139 BLUETOOTH ACCESSORY INSTALLED IN A CB TRANSCEIVER User Manual MANUAL PPR 129RBT 2008 11 18
Ranger Electronic Communications Inc BLUETOOTH ACCESSORY INSTALLED IN A CB TRANSCEIVER MANUAL PPR 129RBT 2008 11 18
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1049492 |
| Application ID | D0+i1zkaxC51Qo8KH9nezw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 28.8kB (360000 bits) |
| Date Submitted | 2008-12-24 00:00:00 |
| Date Available | 2008-12-29 00:00:00 |
| Creation Date | 2008-11-19 09:52:19 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2008-11-19 09:52:19 |
| Document Title | Microsoft Word - MANUAL PPR-129RBT 2008 11 18.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | CHANG JF |
CONTENTS PPR-129RBT 40 Channel AM Mobile CB Radio With Bluetooth Hands Free Profile Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting The Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition Noise Interference . . . . . . . . . . . . . . . . . . . . . . . Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tuning The Antenna for Optimum SWR . . . . . . . . . . . . . External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Public Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frequency Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Procedure to Receive And Transmit . . . . . . . . . . . . . . . . Alternate Microphone And Installation . . . . . . . . . . . . . . Maintenance And Adjustment . . . . . . . . . . . . . . . . . . . . A Few Rules That Should Be Obeyed . . . . . . . . . . . . . . How Your CB Can Serve You . . . . . . . . . . . . . . . . . . . . . 10 11 12 13 16 17 17 USER MANUAL -1- SPECIFICATIONS GENERAL INSTALLATION LOCATION Model Channels Frequency Range Emission Frequency Control Frequency Stability Temperature Range Antenna Impedance Antenna Connectors Input Voltage Size Weight PPR-129RBT 40 26.965 ~ 27.405 MHz AM Phase-Lock-loop (PLL) Synthesizer 0.001% -30C to +50C 50 Ohms Standard SO-239 type 13.8V DC 7- 3/8” (W) x 8- 3/4” (D) x 2- 1/4” (H) 4.2 lbs. TRANSMITTER RF Power Output Spurious Emission Audio Distortion Frequency Response Microphone 4W -60 dB 10% 300 to 2500 Hz Dynamic Plan the location of the transceiver and microphone bracket before starting the installation. Select a location that is convenient for operation and does not interfere with the drive or passengers in the automobiles, the transceiver is usually mounted the dash panel with the microphone bracket beside it. MOUNTING THE RADIO The transceiver is supplied with a universal mounting bracket. When mounting the bracket and radio to your car, make sure it is mechanically strong. Also provide a good electrical connection to the chassis of the vehicle. Proceed as follows to mount the transceiver: 1. After you have determined the most convenient location in your vehicle, hold the transceiver with mounting bracket in the exact desired location. Before drilling the holes, make sure that nothing will interfere with the installation of the mounting bracket. 2. Connect the antenna cable connector to the standard receptacle on the rear panel. Most transceiver antennas are terminated with PL-259 male connector which would mate with the radio’s connector. 3. Connect the red DC power input wire (with the fuse) to +13.8V DC. This wire extends from the rear panel. In automobile installation, +13.8V DC is usually obtained from the accessory contact on the ignition switch. This will prevent the set being left on accidentally when the driver leaves the car and also permits operating the unit without the engine running. 4. Connect the black lead to –13.8V DC. This is usually the chassis of the car. Any convenient location with good electrical contact may be used. 5. Mount the microphone bracket on the right side of the transceiver, using the two supplied screws. RECEIVER Sensitivity for 10 dB (S+N)/N Squelch Sensitivity Image Rejection AGC Figure of Merit Audio Power Output Audio Response < 1.0 uV < 0.5 uV More than 65 dB 100 mV for 10dB Change in Audio Output 3W @ 10% Distortion 300 to 2500 Hz Bluetooth RF Power output RX Sensitivity Working Distance in open space + 4 dBm - 80 dBm 10 m (SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE) -2- -3- INSTALLATION INSTALLATION IGNITION NOISE INTERFERENCE TUNING THE ANTENNA FOR OPTIMUM S.W.R Use of a mobile receiver at low signal levels is normally limited by the presence of electrical noise. The primary source of noise in automobile installation is from the generator and ignition system in the vehicle. Under most operating conditions, when signal level is adequate, the background noise does not present a serious problem. Also, when extremely low level signals are being received, the transceiver may be operated with vehicles engine turned off. The unit requires very little current and therefore will not significantly discharge the vehicle battery. Since there is such a wide variety of a base and mobile antenna, this section will strictly concern itself to the various types of mobile adjustable antennas. Because the antenna length is directly related to the channel frequency, it must be tuned to resonate optimally on all channels of the transceiver. Channel 1 requires a longer antenna than Channel 40 because it is lower in its frequency of operation. Due to the various methods of adjusting antennas for proper S.W.R. we have chosen what we think is the optimum method: Even though the transceiver has ANL and NB controls, in some installation ignition interference may be high enough to make good communications impossible. The electrical noise may come from several sources. Many possibilities exist, as variations between vehicles require different solutions to reduce the noise. A. Antenna with adjustment screws (set screws). 1. Starts with the antenna extended and tighten the set screw lightly enough so that the antenna can be lightly tapped with your finger for easy adjustment. 2. ANTENNA A vertically polarized, quarter-wavelength whip antenna provides the most reliable operation and greatest range. Shorter, loaded-type whip antennas are more attractive, compact and adequate for applications where the maximum possible distance is not required. Also, loaded whips do not present the problems of high wind resistant imposed by a full quarter-wavelength whip. Mobile whip antennas utilize the metal body of the vehicle as a ground plane. When mounted at a corner of the vehicle they are slightly directional, in the direction of the body of the vehicle. For all practical purpose, however, the radiation pattern is nondirectional. The slight directional characteristic will be observed only at extreme distances. A standard antenna connector (type SO-239) is provided on the transceiver for easy connection to a standard PL-259 cable termination. If the transceiver is not mounted on a metal surface, it is necessary to run a separate ground wire from the unit to a good metal electrical ground in the vehicle. When installed in a boat, the transceiver will not operate at maximum efficiency without a ground plate, unless the vessel has a steel hull. Before installing the transceiver in a boat, consult your dealer for information regarding an adequate grounding system and prevention of electrolysis between fittings in the hull and water. -4- Set your transceiver to Channel 20. Press the PTT (push-to-talk) switch, and tap the antenna (making it shorter). The S.W.R meter will show different reading each time the antenna is tapped. By continuing to shorten the antenna, you will notice the S.W.R reading will reach a low point and then start rising again. This means that you have passed the optimum point for Channel 20. Extend the antenna a short distance and again follow the procedure above. When the lowest point has been reached, switch to Channel 1 and then to Channel 40 and compare S.W.R readings, both readings should be similar. NOTE The proper setting is achieved when the SWR is 1.5 or below, and when it has the similar reading for channels 1 and 40. B. Antennas which must be cut to proper length 1. Follow the same procedure as above but adjust the length by cutting in 1/8” increments until a good match is obtained. 2. Be very careful not to cut too much at one time, as once it is cut, it can no longer be lengthed. 3. The whip is easily cut by filing a notch all the way around and breaking the piece off with pliers. -5- INSTALLATION If you’re having difficulties in adjusting your antenna, check the following: a. b. c. d. e. f. OPERATION FRONT PANEL All doors must be closed when adjusting the antenna Make sure the antenna base is grounded. Check your coaxial cable routing (it may be pinched when routed into the car) Try a different location in your car (keeping in mind the radiation pattern you wish.) Is the antenna perfectly vertical? Try a different location in your neighborhood. Stay away from large metal objects when adjusting (metal telephone polls or light post, fences, etc.) NOTE The transceiver will operate into an SWR of 2 to 1 indefinitely and sustain an SWR of 2:1 for a maximum of 5 minutes at rated operating conditions. 1. BLUETOOTH MICROPHONE JACK: Used for connecting a BT microphone for phone call. EXTERNAL SPEAKER The external speaker jack (EXT SP.) on the rear panel is used for remote receiver monitoring. The external speaker should have 8 ohms impedance and be able to handle at least 4 watts. When the external speaker is plugged in, the internal speaker is disconnected. PUBLIC ADDRESS To use the transceiver as a public address system, connect an external 8 ohms speaker (4 watts minimum) to the PA.SP. Jack located on the rear panel. Keep speaker away from the microphone to prevent acoustic feedback. Physical separation or isolation of the microphone and speaker is important when operating the PA at high output levels. 2. CB RADIO MICROPHONE JACK: Used for connecting a CB microphone for voice source. 3. MIC GAIN CONTROL: Adjust the microphone gain in the transmitting and PA modes. This controls the gain to the extent that full talk power is available several inches away from the microphone. In the Public Address (PA) mode, the control functions as the volume control. 4. RF GAIN CONTROL: This control is used to reduce the gain of the RF amplifier under strong signal conditions. 5. ON/OFF VOLUME CONTROL: This knob controls the volume and power to the radio. To turn radio on, rotate the knob clockwise. Turning the knob further will increase the volume of the receiver. 6. SQUELCH CONTROL: This switch is used to eliminate background noise being heard through the receiver, which can be disturbing when no transmission is being heard through the received. To use this feature, turn the switch fully counterclockwise and then turn clockwise slowly until the background noise is just eliminated. Further clockwise rotation will increase the threshold level, which a signal must overcome in order to be heard. Only strong signal will be heard at a maximum clockwise setting. -6- -7- OPERATION OPERATION 7. TALKBACK CONTROL: Adjust this knob for desired volume of Talkback. This is used to monitor your own voice. This feature could be used for comparing TX audio from different microphones. 17. PHONE VOLUME▼DOWN SWITCH: This Push switch has dual function; it is used for turning down the volume for phone call, and is used to set the time for the clock. 8. TX/RX LED: The Red LED indicates the unit is in the transmit mode. The Green LED indicates the unit is in the receive mode. 18. PHONE VOLUME UP▲SWITCH: This Push switch has dual function; it is used for turning up the volume for phone call, and it is used to set up the time for the clock. 9. CHANNEL SELECTOR: This control is used to select a desired transmit and receive channel. 19. ANSWER SWITCH: This is a multifunction switch for Bluetooth operation; please refer to the chart below. 10. ANT LED: This LED lights red when your SWR is higher than about 3:1. This is not an exact indicator of 3:1 SWR, but it is an indication that you should check your antenna and its components. 11. FRONT PANEL METER: The Front Panel Meter allows the user to monitor the incoming signal strength and RF power output. 12. PA/CB SWITCH: In the PA position, the radio acts as public address amplifier. Your voice will come out of the speaker that is plugged into the PA. SP. jack on the rear panel. The CB will not operate when you are in the PA mode. In the CB position, the PA function is disabled and the CB transceiver is functional. 13. CALLER ID DISPLAY: The Caller ID shows the telephone number of the incoming call (if available) and the number being dialed. 14. NB ANL/ANL/OFF SWITCH: In the ANL position, the Automatic Noise Limiter (ANL) in the audio circuits is activated. In the NB position, the Noise Blanker (NB) is activated. The NB is very effective in eliminating repetitive impulse noise such as ignition interference. 15. CH19/NORMAL SWITCH: This switch is used to access Channel 19 instantly. 16. DIMMER SWITCH: This Push switch has dual function; it adjusts the level of brightness for the meter lamp and the LED. In addition, this switch is used in conjunction with the Phone Volume UP & Down switches for setting the time for the clock. Press and hold this switch for 3 seconds and the first two digits (hour) of the clock will flash, set the hour by using the Phone Volume switches. Once the desired hour is set, short press the Dimmer switch to set the minutes. Once the desired time is set, press the Dimmer switch momentarily to activate the clock. The time is displayed in military configuration (e.g., 1:30 PM will read as 1330 Hrs, 1: 00AM will read as 0100 Hrs). -8- Switch Action Bluetooth Condition Power HFP HFP Incoming Outgoing Active Off Connections Connected Call Call Call Short Press N/A (Answer SW) Connect to last AG Long Press Power Connect to last AG (Answer SW) On Voice Dial/ Cancel Voice Dial (toggle) Last Number Redial Power Off Answer Call End Call End Call N/A N/A Transfer Audio Enter Power Off Power Off Power Off Power Extra Long Pairing Off Press (Answer SW) Enter Pairing Enter Reject Call N/A N/A Double Short N/A Pairing Press (Answer SW) N/A Volume Volume Volume Volume Short Press N/A Down Down Down Down (Phone Vol SW ▼) N/A Volume Up Volume Up Volume Volume Short Press N/A Up Up (Phone Vol SW▲) ***Short Press =1 second ***Long Press= 3 seconds ***Extra Long Press= 8 seconds ***HFP= Hands Free Profile ***AG= Audio Gate -9- OPERATION 20. BLUETOOTH LED: This LED allows the user to monitor the Bluetooth Operation. Bluetooth State LED Blue LED one flash every 2 seconds Connecting Blue LED two flashes every 2 seconds Connected Blue LED two flashes every 2 seconds Voice Dialing Incoming call Outgoing call Active call Pairing Mode Blue LED two flashes every 2 seconds Blue LED two flashes every 2 seconds Blue LED always on Blue and Red LED flashes alternately 21. CHANNEL DISPLAY: The channel display indicates the current selected channel. REAR PANEL 1. ANTENNA: This jack accepts 50 ohms coaxial cable with a PL-259 type plug. 2. DC POWER: This accepts 13.8V DC power cable with built-in fuse. The power cord provided with the radio has a black and red wire. The black goes to negative and red goes to positive. 3. EXT. SP: This jack accepts 4 to 8 ohms, 5 watts external speaker. When the external speaker is connected to this jack, the built-in speaker will be disabled. OPERATION FREQUENCY CHART Channel Channel Frequency Channel Channel Frequency 26.965 MHz 21 27.215 MHz 26.975 MHz 22 27.225 MHz 26.985 MHz 23 27.255 MHz 27.005 MHz 24 27.235 MHz 27.015 MHz 25 27.245 MHz 27.025 MHz 26 27.265 MHz 27.035 MHz 27 27.275 MHz 27.055 MHz 28 27.285 MHz 27.065 MHz 29 27.295 MHz 10 27.075 MHz 30 27.305 MHz 11 27.085 MHz 31 27.315 MHz 12 27.105 MHz 32 27.325 MHz 13 27.115 MHz 33 27.335 MHz 14 27.125 MHz 34 27.345 MHz 15 27.135 MHz 35 27.355 MHz 16 27.155 MHz 36 27.365 MHz 17 27.165 MHz 37 27.375 MHz 18 27.175 MHz 38 27.385 MHz 19 27.185 MHz 39 27.395 MHz 20 27.205 MHz 40 27.405 MHz 4. PA SP.: This jack is for PA operation. Before operating, you must first connect a PA speaker (8 ohms, 4W) to this jack. - 10 - - 11 - OPERATION OPERATION PROCEDURE TO RECEIVE AND TRANSMIT ALTERNATE MICROPHONES AND INSTALLATION A. MICROPHONE The receiver and transmitter are controlled by the push-to-talk switch on the microphone. Press the switch the transmitter is activated, release switch to receive. When transmitting, hold the microphone two inches from the mouth and speak clearly in a normal voice. This transceiver comes complete with a low impedance dynamic microphone. For best results, the user should select a low-impedance dynamic type microphone or a transistorized microphone. Transistorized type microphones have low output impedance characteristics. The microphones must be provided with a four-lead cable. The audio conductor and its shielded lead comprise two of the leads. The third lead is for transmit control and fourth is for receiving control. B. PROCEDURE TO RECEIVE 1. Be sure that power source, microphone and antenna are connected to the proper connectors before going to the next step. The microphone should provide the functions shown in schematic below. 2. Turn VOL knob clockwise to apply power to the radio. 3. Set the VOL for a comfortable listening level. 4. Set the MODE switch to the desired mode. 5. Listen to the background noise from the speaker. Turn the SQ knob slowly clockwise until the noise just disappears. The SQ is now properly adjusted. The receiver will remain quiet until a signal is actually received. Do not advance the control too far or some of weaker signals will not be heard. 4 WIRE MIC CABLE Pin Number Mic Cable Lead Audio Shield Audio Lead Transmit Control Receive Control 6. Set the CHANNEL selector switch to the desired channel. 7. Set the RF GAIN control fully clockwise for maximum RF gain. 8. Adjust the CLARIFY control to optimize AM signals. C. PROCEDURE TO TANSMIT 1. Select the desired channel of transmission 2. Set the MIC GAIN control fully clockwise. 3. If the channel is clear, depress the push-to-talk switch on the microphone and speak in a normal voice. Fig. 1 Your transceiver microphone schematic. If the microphone to be used is provided with precut leads, they must be revised as follows. 1. Cut leads so that they extend 7/16" beyond the plastic insulating jacket of the microphone cable. 2. All leads should be cut to the same length. Strip the ends of each wire 1/8" and tin the exposed wire. - 12 - - 13 - OPERATION Before beginning the actual wiring, read carefully the circuit and wiring information provided with the microphone you select. Use the minimum heat required in soldering the connections. Keep the exposed wire lengths to a minimum to avoid shorting when the microphone plug is reassembled. OPERATION 5. The wires must now be soldered to the pins as indicated in the above wiring tables. If a vise or clamping tool is available it should be used to hold the pin receptacle body during the soldering operation, so that both hands are free to perform the soldering. If a vise or clamping tool is not available, the pin receptacle body can be held in a stationary position by inserting it into the microphone jack on the front panel. The numbers of the microphone plug are shown in Fig. 3, as viewed from the back of the plug. Before soldering the wire to the pins, pre-tin the wire receptacle of each pin of the plug. Fig. 3 Microphone plug pin numbers viewed from rear of pin receptacle. 6. Be sure that the housing and the knurled ring of Figure 2 are pushed back onto the microphone cable before starting to solder. If the washer is not captive to the pin receptacle body, make sure that it is placed on the threaded portion of the pin receptacle body before soldering. Fig. 2 Microphone plug wiring To wire the microphone cable to the plug provided, proceed as follows: 1. Remove the retaining screw. 7. If the microphone jack is used to hold the pin receptacle during soldering operation, best results are obtained when the connections to pin 1 and 3 are made first and then the connections to pins 2 and 4. Use a minimum amount of soldering and be careful to prevent excessive solder accumulation on pins, which could cause a short between the pin and the microphone plug housing. 4. Feed the microphone cable through the housing, knurled ring and washer as shown Figure 2. 8. When all soldering connections to the pins of the microphone are completed, push the knurled ring and the housing forward and screw the housing onto the threaded portion of the pin receptacle body. Note the location of the screw clearance hole in the plug housing with respect to the threaded hole in the pin receptacle body. When the housing is completely threaded into the pin receptacle body, a final fraction of a turn either clockwise or counterclockwise may be required to align the screw hole with the threaded hole in the pin receptacle body. When these are aligned, the retaining screw is then screwed into place to secure the housing to the pin receptacle body. - 14 - - 15 - 2. Unscrew the housing from the pin receptacle body. 3. Loosen the two cable clamp retainer screws. OPERATION 9. The two cable clamp retainer screws should now be tightened to secure the housing to the microphone cord. If the cutting directions have been carefully followed, the cable clamp should secure to the insulation jacket of the microphone cable. OPERATION A FEW RULES THAT SHOULD BE OBEYED 1. You are not allowed to carry on a conversation with another station for more than five minutes at a time without taking a one-minute break, to give others a chance to use the channel. MAINTENANCE AND ADJUSTMENT 2. You are not allowed to blast others off the air by over-powering them with illegally amplified transmitter power, or illegally high antennas. This transceiver is specifically designed for the environment encountered in base installations. The use of all solid state circuitry and its light weight result in high reliability. Should a failure occur, however, replace parts only with identical parts. Do not substitute. 3. You can’t use the transceiver to promote illegal activities. 4. You are not allowed to use profanity. 5. You may not play music in your transceiver. 6. You may not use your transceiver to sell merchandised or professional service. 10. Upon completion of the microphone plug wiring, connect and secure the microphone plug in the transceiver. NOTE If the performance described in the OPERATION and MAINTENANCE AND ADJUSTMENT sections is not obtained, review the operating instructions to insure that proper procedures were followed. FCC WARNING All transmitter adjustments other than those provided on front panel by the manufacturer must be made by or under the supervision of the holder of an FCC – issued general radiotelephone operator’s license. - 16 - HOW YOUR CB CAN SERVE YOU 1. Warn of traffic tie-ups ahead. 2. Provide weather and road information. 3. Provide help fast in event of emergency or breakdown. 4. Suggest good spots to eat and sleep. 5. Make long trips more interesting, and help keep you awake. 6. Provide direct contact with your office or home. 7. Make friends for you as you travel. 8. Provide “local information” to find your destination. 9. Help law enforcement officers by reporting drunk and reckless drivers. - 17 - Memo PRINTED IN CHINA A38200726A - 18 - - 19 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Create Date : 2008:11:19 09:52:19+08:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2008:11:19 09:52:19+08:00 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : Microsoft Word - MANUAL PPR-129RBT 2008 11 18.doc Creator : CHANG JF Document ID : uuid:02ee0ec6-7730-427e-9f2b-8098c70c1667 Instance ID : uuid:9c98d555-3aa9-40b9-9a6b-fa11ed30b7c5 Page Count : 10 Author : CHANG JFEXIF Metadata provided by EXIF.tools