Ranger Electronic Communications 5054DX100 Communications Receiver User Manual RCI5054 100

Ranger Electronic Communications Inc Communications Receiver RCI5054 100

users manual

AM/FM/SSB/CW 6 Meter Amateur Mobile Transceiver Owner's Manual RCI-5054DX / RCI-5054DX -100 - 1 - Table of Contents PAGE Chapter 1 Specifications ....................................................... 2 Chapter 2 Introduction .......................................................... 3 Unpacking ........................................................................... 3 Chapter 3 Installation ............................................................ 4 Transceiver Mounting ........................................................... 4 Power Connection ............................................................... 4 Chapter 4 Operation .............................................................. 5 Front Panel .......................................................................... 5 Rear Panel ........................................................................... 9 Microphone ......................................................................... 10 Frequency Selection ............................................................. 11 Mode Selection .................................................................... 12 RF Power Control ................................................................. 12 Chapter 5 Programming ........................................................ 13 Receive Scanning ............................................................... 13 Split Function ....................................................................... 13 Memory Function ................................................................. 13 Memory Channel Scanning ................................................... 14 Metering .............................................................................. 14 Chapter 6 Frequency Si 14 All-Frequency Scanning ........................................................ 15 Memory Scanning ................................................................ 16 Chapter 7 Offset Frequency Oi 17 Memo .................................................................................... 18 LIMITED WARRANTY .............…............................. Inside Back Cover
- 2 - Chapter 1 Specifications GENERAL Model RCI-5054DX RCI-5054DX-100 Frequency Range : 50.000 ~ 54.000 MHz 50.000 ~ 54.000 MHz Tuning Steps 100 Hz, 1 KHz, 10 KHz, 100 KHz, 1 MHz 100 Hz, 1 KHz, 10 KHz, 100 KHz, 1 MHz Emission USB, LSB, CW, AM, FM USB, LSB, CW, AM, FM Frequency Control Phase-Lock-Loop Synthesizer Phase-Lock-Loop Synthesizer Frequency Tolerance 0.005% 0.005% Frequency Stability 0.001% 0.001% Operating Temperature Range -10OC to +50OC -10OC to +50OC Antenna Impedance 50 ohm 50 ohm Microphone Plug-In (6-Pin), 400 Ω Dynamic PTT Plug-In (6-Pin), 400 Ω Dynamic PTT Meter Function RF Output, RX Receive Signal Strength, SWR RF Output, RX Receive Signal Strength, SWR Input Voltage 13.8 V DC 13.8 V DC Dimensions 7 3/4" (W) x 10 3/4" (D) x 2 3/8" (H) 7 3/4" (W) x 9 3/4" (D) x 2 7/8" (H) Weight 4 lb. 3 oz. 5 lb. 13 oz. TRANSMITTER RF Power Output 25W : USB/LSB Peak Power 10W : CW/AM/FM 100W : USB/LSB Peak Power 50W : CW/AM/FM RF Transmit Modes USB, LSB, CW, AM, FM USB, LSB, CW, AM, FM Antenna Connector UHF Type, 50 Ω UHF Type, 50 Ω Modulation 16F3, A3E, J3E, A1A 16F3, A3E, J3E, A1A Spurious Emissions >60 dB >60 dB Carrier Suppression -50 dB -50 dB RECEIVER Sensitivity AM/CW : 0.5 uV for 10dB Sinad FM : 0.25uV for 12dB Sinad USB/LSB : 0.15uV for 10dB Sinad AM/CW : 0.5 uV for 10dB Sinad FM : 0.25uV for 12dB Sinad USB/LSB : 0.15uV for 10dB Sinad Image Rejection Ratio -65 dB -65 dB AGC Figure of Merit SSB/CW/AM : 80dB at 50mV for a 10dB change in Audio Output SSB/CW/AM : 80dB at 50mV for a 10dB change in Audio Output Audio Power Output 2.5W 2.5W ( SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE ) - 3 - Chapter 2 Introduction Congratulations on your purchase of an RCI-5054DX/5054DX-100 6 meter amateur radio. Your RCI-5054DX/5054DX-100 is designed to provide trouble-free service and state-of-the-art communications in the 6 meter band. Please read this manual thoroughly to ensure proper performance. Unpacking The following items are included with our RCI-5054DX/5054DX-100. Carefully remove and examine all materials from the packing carton. If any items are missing or appear damaged, please contact your dealer immediately. Each unit should include: (1) RCI-5054DX/5054DX-100 Transceiver (2) Dynamic Microphone with remote frequency adjustment switches (3) Power Cord (4) Mounting Bracket & Hardware (5) Installation Hardware (6) Owner's Manual (7) Warranty Registration Card It is recommended that you save the packing materials for future storage or shipping. IMPORTANT To operate this radio, you must possess and amateur radio operator's license issued by the FCC. Operation of this unit without proper licensing is ILLEGAL and can result in severe penalties. NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate this equipment.
- 4 - Chapter 3 Installation The RCI-5054DX/5054DX-100 is easy to install. All necessary parts (less the antenna and coax cable) have been included to facilitate installation. Transceiver Mounting Choose a suitable location for the transceiver that will allow easy access to the front panel as well as proper air circulation to the back of the unit. If you are installing the unit in a vehicle, attach the mounting bracket first, then attach the transceiver to the mounting bracket using the hardware provided. Before making any electrical connection, ensure that the transceiver is turned off and the vehicle's battery is disconnected. Power Connection The transceiver operates off of any 12 to 13.8 VDC source. Beware of voltage drops caused by operating from Cigarette Lighter Plugs or long DC wire runs. Sometimes it is best to connect direct to the battery for best RF output and Tx audio quality If an AC power supply is used with your radio, it must be regulated and rated for at least 7 Amps continuous for the RCI-5054DX and 20 Amps continuous for the RCI-5054DX-100. Low voltage while under load will cause reduced receiver gain and low transmitter output with possible distortion and splatter. NOTE The condition of a vehicle's electrical system can affect the operation of your RCI-5054DX/5054DX-100. A low battery, worn generator/ alternator, or poor voltage regulator will impair performance of the unit as well as the vehicle. CAUTION Voltage above 15 VDC will damage the unit. Be sure to check the source voltage before connecting the power cord. - 5 - SWRDIM SCAN MEM LOCKENTAMFMRCI−5054DXMANR.BEEPNB/ANL SPLIT PRG SHFCLR GAINRFUSBLSBCWOFFRF MICPWR VOLPASQ924 1510 1116 17121813 1419 202121 678352423221Chapter 4 Operation Front Panel 1. FREQUENCY SELECTOR: Used to set the desired transmit and receive frequency. The frequency is digitally displayed in the LCD window next to the selector. The FREQUENCY SELECTOR knob next to the LCD display, allows changing each digit on the frequency display by first placing the frequency display cursor (using SHF button) below the desired digit and then turning the selector knob. 2. RF POWER CONTROL: This control adjust the Transmitter’s RF power output level. 3. MIC GAIN CONTROL: This feature adjust the microphone gain for the transmit and PA modes. Experiment with this control for the setting that will provide best audio quality. Avoid overmodulation, which causes interference to adjacent stations and “splatter”. 4. ON/OFF VOLUME CONTROL: Turn clockwise to apply power to the radio and to set the desired listening level.
- 6 - Operation (Continued) 5. SQUELCH CONTROL: This control is used to control or eliminate receiver background noise in the absence of an incoming signal. For maximum receiver sensitivity, it is necessary that the control be adjusted only to the point where the receiver background noise is eliminated. Turn fully counterclockwise and then slowly clockwise until the receiver noise just disappears. Any signal to be received must now be slightly stronger than the average received noise. Further clockwise rotation will increase the threshold level that a signal must overcome in order to be heard. Only strong signals will be heard at a maximum clockwise squelch setting. 6. RF GAIN CONTROL: This control is used to reduce the receiver's front-end gain when receiving strong signals. 7. CLARIFIER CONTROL: Allows variation of the receive frequency above and below the selected receive frequency as shown on the display. This control is intended primarily to tune in SSB signals when communicating with several stations that may not be exactly on frequency. It may also be used to optimize AM/FM signals as described in the operating procedure paragraph. The clarifier can adjust the receive frequency ±2.5KHz but does not affect the transmit frequency or the frequency display. 8. MODE SWITCH: This switch allows you to select one of the following six operating modes: FM, AM, USB, LSB, CW and PA. 9. NB/ANL BUTTON (NB/ANL): The noise blanker (NB) is very effective in eliminating repetitive impulse noise such as ignition interference. In the ANL position, the AUTOMATIC NOISE LIMITER also limits noise at the receiver audio stages. 10. ROGER BEEP BUTTON (R.BEEP): This switch activates the ROGER BEEP circuit, when its function is selected. When enabled, the radio automatically transmits an audio tone each time you release the PTT. This indicates the end of each transmission so that stations who may - 7 - Operation (Continued) be having trouble receiving will know that you have finished transmitting. This feature is sometimes used in weak signal conditions or other special circumstances. We discourage use of this feature in normal operation, as it can be annoying to other operators. 11. SPLIT BUTTON (SPLIT): Enables the offsetting of the transmitter frequency by up to ± 2 MHz (programmable) for FM repeater operation. 12. PROGRAM BUTTON (PRG): Used to pre-program operating or scanning frequencies into memory. See the OPERATION section of this manual for details. 13. MANUAL BUTTON (MAN): Used to return the unit to manual mode. 14. SHIFT BUTTON (SHF): Determines which digit will change when changing frequencies, by placing a “cursor” under the desired digit. Allows frequency to be changed in 100 Hz, 1KHz, 10KHz, 100KHz and 1 MHz increments. 15. DIM BUTTON (DIM): This button adjusts the display backlighting in four different steps to best match the ambient light. 16. SWR BUTTON (SWR): Used to check relative SWR. 17. SCAN BUTTON (SCAN): Used to enable the scanning of frequencies. See the PROGRAMMING and SCANNING section of this manual for detailed information on using the scan control. 18. MEMORY BUTTON (MEM): Used to program often used frequencies in memory. Detailed information on how to use this control is provided in the PROGRAMMING section of the manual. 19. ENTER BUTTON (ENT): Used to program frequencies in memory. See PROGRAMMING section.
- 8 - Operation (Continued) 20. LOCK BUTTON (LOCK): Disables the Frequency Selector Control, UP/DOWN buttons on the front control panel and remote UP/DOWN buttons on the microphone. Pressing this switch again will re-enable the frequency selectors. 21. UP/DOWN SELECTOR: These buttons are used to increase or decrease the frequency digit above the SHF cursor on the display. - 9 - 23451Operation (Continued) Rear Panel 1. ANTENNA: This jack accepts a 50 ohms coaxial cable with a PL-259 style plug. 2. CW KEY: The CW key is used for Morse Code operation. To operate connect a CW key to this jack, and place the mode switch in the CW position. 3. EXTERNAL SPEAKER: This jack accepts a 4 - 8 ohm 5W external speaker. When an external speaker is connected to this jack, the built-in speaker is disabled. 4. PA SP.: An 8 ohm, 4W PA speaker may be connected to this jack for PA operation. This feature operates by placing mode selector in PA position. 5. POWER: This socket accepts a 13.8 VDC power cable with built-in fuse. The power cord provided with the radio consists of a black wire (negative) and a red wire (positive ).
- 10 - Operation (Continued) Microphone 1. PTT SWITCH: The Push-To-Talk (PTT) switch controls the transmit and receive function of the radio. Push to transmit and release to receive. 2. REMOTE UP/DOWN SWITCH: The digit on the frequency display above the SHF “cursor” can be stepped up or down by pushing either of these buttons. For best results, the user should select a low-impedance dynamic type microphone or a transistorized microphone. The microphone should provide the functions shown in schematic below. 6 WIRE MIC CABLE Pin Number Mic Cable Lead 1 Audio Shield 2 Audio Lead 3 Transmit Control 4 Receive Control 5 Up Control 6 Down Control Transceiver Microphone Schematic Diagram - 11 - Operation (Continued) Frequency Selection Frequency selection in the RCI-5054DX/5054DX-100 can be accomplished using any one of the following three methods: 1. The first method of frequency selection uses the SHF (Shift) key and the ▲(UP)/▼(DOWN) keys located on the front panel. To accomplish this, press the SHF key until the display cursor on the frequency display is positioned under the frequency digit that is to be changed. Use the”▲” key to increase the number. Press the “▼” key to decrease the number. Perform the steps described above for each digit until the desired frequency is displayed in the LCD frequency display window. 2. The second method of frequency selection is performed using the SHF key and the FREQUENCY select knob located on the front panel. Use the SHF key in the manner described above to select the digit to be changed. Then rotate the FREQUENCY selector clockwise to increase the frequency and counterclockwise to decrease the frequency. 3. The third method of frequency selection is through the use of the SHF key and the remote UP and DOWN buttons located on the microphone. Frequency selection by this method is accomplished in the same manner as with the “▲” key and the “▼” key on the front panel keypad. Sometimes when receiving more than one station on a fixed frequency such as on a “Net” or “round table” operation, it is convenient to be able to vary the receive frequency slightly without changing the transmit frequency. To do this, rotate the clarifier control while an off frequency station is transmitting. You can vary the receiver frequency by ±2.5 KHz for clearest voice reception. The clarifier can be optionally modified to vary both Transmit and Receive frequencies together.
- 12 - Operation (Continued) Mode Selection To Select an operating mode, rotate the MODE selector, and place it in the desired operating mode position. RF Power Control This feature allows the adjustment of the RF output power continuously over the range of 1W through 25W. - 13 - Chapter 5 Programming Receive Scanning The receive scanning feature helps locate active frequencies within a preprogrammed band segment anywhere on the 6 Meter band (refer to SCANNING, page 16). To begin scanning, slowly turn the Squelch control clockwise until the receiver noise disappears. Next, press the scan button. The unit should start scanning from the lower to the higher frequencies. Pressing the Scan button again will change the direction of scanning. Each time the Scan button is pressed, "SCAN+" or "SCAN-" will be displayed on the LCD display. The scan will stop on any active frequency for the duration of the transmission. After the on frequency activity stops, the RCI-5054DX/5054DX-100 will resume scanning after about a 2 second pause. To deactivate the Scan mode, press the MAN (manual) button or turn the Squelch control counterclockwise until you hear receiver noise. The MAN button will disable the Scan function. Split Function This function enables you to split the transmit and receive frequencies for by a pre-programmed amount. This feature is necessary for operation with FM repeaters. (See OFFSET FREQUENCY OPERATION, pg. 17 for more information). To split frequencies, press the MAN button and the SPLIT button to select + split frequency (transmitter higher than receiver). For - split frequency, press the SPLIT button again (transmitter lower than receiver). Memory Function The RCI-5054DX/5054DX-100 can store up to 10 frequencies in memory locations 0 to 9. To program a frequency into memory, follow the procedure described below: 1. Press the MAN button. 2. Press the PRG button. 3. Press the MEM button. ("MEMORY" and "0" should appear on the left-hand side of the LCD display). Each press of the MEM button will advance the memory location one step at a time from "0" to "9".
- 14 - Programming (Continued) 4. Set the desired frequency you wish to store in memory. 5. Press the ENT button. 6. Repeat the procedure to program other memory channels. Memory Channel Scanning You can scan the 10 pre-programmed memory locations by following the procedure described below: 1. Press MAN button. 2. Press the MEM button. 3. Slowly turn the Squelch knob clockwise until the receiver noise disappears. 4. Press the Scan button. The unit will scan from lower to higher memory locations. Pressing scan again will cause the unit to scan from higher to lower memory locations. 5. To stop scanning while on a memory location, press the MAN button. You can also turn the Squelch knob counterclockwise until you hear the receiver noise. Metering The segmented bars on the left-hand side of the LCD display provide the following information: 1. S/RF METER: Provides a relative indication of transmit RF output power while transmitting or signal strength while receiving 2. SWR METER: This function allows the checking of relative SWR. To use this function, set the unit to AM mode and push the SWR button on the front panel while holding down the PTT switch on the microphone. The bars on the meter will indicate approximate SWR. If there is no bar, your antenna system is well matched. If several bars appear, the antenna needs adjustment. The fewer the bars, the better the match. - 15 - .Chapter 6 Frequency Scanning Frequency scanning can be achieved by either of two methods: the first method involves scanning of all frequencies between a pre-set upper and lower scan frequency. The second method permits the scanning of frequencies previously programmed in the memory locations 0 thru 9. All-Frequency scanning To allow All-Frequency scanning, the user must first program the upper and lower scan limit frequencies as follows: 1. Press the PRG (Program) key. 2. Press the SCAN key. ("PRG SCAN+" should appear in the lower right-hand corner of the display window.) 3. Using the SHF key and the UP and DOWN arrows, select the upper scan limit frequency. 4. Press the SCAN key again. ("SCAN-" should appear in the display window.) 5. Using the SHF key and UP and DOWN arrows, select the lower scan limit frequency, then press ENT. The upper and lower scan limits have now been programmed. To activate the scan feature, return the radio to manual operation and press the SCAN button. If the display shows "SCAN+", the radio will scan from the lower limit to the upper limit. If "SCAN-" is displayed, the unit will scan from the upper limit to the lower limit. To change from "SCAN+" to "SCAN-" or vice versa, press SCAN. NOTE Whichever upper and lower scan limits are programmed in, are also the upper and lower operating limits of the radio. The radio will not operate above or below the scan limits last programmed in. Full band coverage can be returned by reprogramming the original band edges.
- 16 - Frequency Scanning (Continued) Memory Scanning The RCI-5054DX/5054DX-100 has 10 non-volatile memory locations which can be programmed with any frequency within the operating range of the radio. The scan function of the unit can scan the frequencies in the 10 memory locations. The first step in utilizing the memory scan function is programming the desired frequencies into the memory locations 0 through 9 by performing the following steps: 1. With the radio operating in the manual mode, press the PRG (Program) key. 2. Press the MEM key. "PRG" should display in the lower right-hand corner of the LCD display. "MEM" should display in the upper left portion of the display. A number between 0 and 9 will display directly below MEM. This number represents the memory location currently being shown on the frequency display. Pressing the MEM key will increase the memory counter to the next memory location and the frequency in that memory location will be displayed. 3. Set the new frequency to be stored in the memory location displayed by using the SHF key and the UP and DOWN arrows. After the desired frequency is indicated, press ENT. This will overwrite whatever frequency had been previously stored at this location. 4. Repeat steps 2 and 3 for all of the memory locations to be programmed. 5. After the desired memory locations have been programmed with frequencies, return the unit to the manual mode of operation by pressing the MAN key. 6. To initiate memory scanning, press MEM and then SCAN. The display will show "SCAN+" or "SCAN-" to indicate whether the radio is scanning from the lowest to the highest memory location or vice versa. To return the radio to normal (non-scanning) operation, press the MAN key. - 17 - Chapter 7 Offset Frequency Operation The split frequency function offsets the transmitter frequency either above or below the receiver frequency by a user-programmable amount. This is necessary for operating on FM repeaters. In the following example, the programming of a 1 MHz offset will be described. Before attempting to program the offset frequency, ensure that the radio is operating in the manual mode by pressing the MAN key. NOTE: FM repeaters may require that a sub-audible CTCSS tone be transmitted to gain access to the repeater. The RCI-5054DX/5054DX-100 can be equipped with an optional CTCSS encoder. TO PROGRAM TX OFFSET: 1. Press the PRG (Program) key. 2. Press the SPLIT key. The LCD display will indicate 00000 with PRG and SPLIT showing in the lower left-hand corner of the display. 3. Using the SHF key and the UP and DOWN arrows as described earlier, program the display to read 10000. 4. Press ENT. A 1 MHz offset has now been programmed into the radio. 5. Return the radio to manual operation by pressing the MAN key. 6. Using the SHF key and the UP and DOWN arrows as described previously, set the radio to the desired receive frequency. 7. Press SPLIT. Either "SPLIT+" or "SPLIT-" will be displayed in the lower right corner of the display. If "SPLIT+" is displayed, the transmitter will be offset 1 MHz above the receive frequency when keyed. If "SPLIT-" is displayed, the transmitter will be offset 1 MHz below the receive frequency. NOTE When the transmitter is keyed, the frequency display will change to show the frequency being transmitted.
- 18 - Memo - 19 - Ranger Communications Limited Warranty Ranger Communication, Inc. (Ranger) warrants to the original purchaser only this product against defects in material or workmanship, as noted below. Effective December 1, 2001, the following Ranger Communications, Inc.'s products are covered by a two (2) year limited warranty: 1. Amateur Radio Products: RCI-2950DX, RCI-2970DX, RCI-2980WX, RCI-2985DX, RCI-2990DX, RCI-2995DX, RCI-6300FHP, RCI-6300FTB, RCI-6900FHP, RCI-6900FTB, RCI-6300F25/150, RCI-6900F25/150, RCI-5054DX, RCI-5054DX-100. 2. Citizens Band Products: TR-100 Series, TR-296 (all models), TR-396F, TR-696F, TR-696F SSB, TR-900 Series (all models). The above products are warranted for the specified time period from the original date of purchase as shown on the original purchaser’s bill of sale, receipted invoice, or other proof of purchase. After this period, the original purchaser must pay for any labor at the prevailing rate either at an authorized Ranger warranty repair facility or at the factory. In the event of a defect during the warranty period, Ranger shall, at its option, repair or replace the defective product. Such action shall constitute the purchaser’s exclusive remedy under this warranty. A Return Authorization Number must be obtained from the Ranger Customer Service Department before any returns for warranty repair will be accepted. Send the defective product postage-paid, along with proof of the date of purchase (photocopy of the original invoice or receipt), to: Ranger Communications, Inc. 401 W. 35th Street, Suite B National City, Ca 91950-7909 TEL: (800) 446-5778, (619) 426-6440 FAX: (619) 426-3788 E-mail: rci@rangerusa.com This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, improper installation, UNAUTHORIZED MODIFICATION, or any action in violation of the product’s instruction manual. This warranty is valid only in the U. S. A. 1. "Limited" means that we will repair problems that are caused by factory defects, only for the above mentioned products and time limit, at no charge. Work performed by qualified technicians which did not cause any damage to the radio will not void the warranty. Problems or damage caused by unqualified or misinformed technicians, operator abuse or other miscellaneous actions may be able to be repaired, but there will be a charge. This warranty is limited to the radio only. 2. Generally, if the warranty sticker is removed or cut, the radio is considered to be "Void of Warranty". However, our policy is to be as lenient as we can, and to take this into consideration. We will usually repair the radio - under warranty - if no abuse or misuse is found. Radios that have parts removed cut or clipped; or the PCB has been damaged, will not be repaired under warranty.
- 20 - 401 W. 35th Street, Suite B National City, CA 91950 (800) 446-5778 • FAX (619) 426-3788 Email: rci@rangerusa.com http: //www.rangerusa.com PRINTED IN TAIWAN AT5054010B

Navigation menu