Raymarine 4000 Mk2 Users Manual D5603_1

4000 MK2 to the manual c211627f-3efa-4a5a-abfc-cc55f8b370fd

: Raymarine Raymarine-4000-Mk2-Users-Manual-125970 raymarine-4000-mk2-users-manual-125970 raymarine pdf

Open the PDF directly: View PDF .
Page Count: 1

Download
Open PDF In Browser	View PDF

Raymarine 4000 mk2 Wheel Drive - Bulkhead/Box Pedestal Fitting Kit (E15017)
Installation Template and Instructions
Parts Supplied
Instructions

Metal
ring

Rubber
seal

Note: Before following these instructions, attach the wheel drive to the wheel (refer to the
ST4000+ Owner's Handbook for details).
No 10 x 3/4 in
self-tapping screw (x 6)

Preparation

1. Cut out the appropriate 'wheel spindle' circle (at the center of this template), so you
can place the template over your wheel spindle.
2. Rotate the template to determine suitable locations for the motor tube and bracket:
• You may be able to orientate the wheel drive so the motor tube runs alongside the
pedestal. In this case, proceed to 'Cutting the bracket'.
• There are two alternative slots for the bracket in the back cover of the wheel drive
(Slot 1 and Slot 2).
• Locate the motor tube where:
• a 55 mm (21/8 in) hole can be cut in the bulkhead/pedestal (if required)
• the seal and ring can be secured around the motor tube
• there is sufficient space behind the mounting location to allow at least 10 mm
(0.4 in) clearance around the motor (see diagram below)
CAUTION:
Mount the drive so the motor tube is as far as possible from the boat's
compass to reduce the risk of deviation.
3. Use the template to mark the locations of the bracket and motor tube.

Bracket

Slot 2

Bracket location
(alternative)

:

ter

me
dia
ce )
n
a
in
ar
cle 2.7
um mm (
m
i
min 68

in)
2/
m ( r hole
m
55 mete
dia

Typical installation

15

4m
m

(6.

1 8

1i
n)

up re
to qui
19 red
0 d
m ep
m th
(7 :
.5
in
)

mm
154 n)
i
1
(6.

Cutting the motor tube hole

1. Drill a small pilot hole at the center of the intended motor tube location so you can
check there is sufficient clearance behind the mounting location.
CAUTION:
Before you cut the motor tube hole, check behind the intended
location for any steering mechanisms, cables or obstructions.
2. Cut a 55 mm (21/8 in) diameter hole at the motor tube location and smooth any
sharp edges.
3. Assemble the ring/seal onto the motor tube:
• fit the metal ring first
• then fit the rubber seal: the seal will self-center on the tube
4. Temporarily mount the wheel and drive onto the spindle, allowing
the motor tube to pass through the hole.
5. Press the seal against the bulkhead/pedestal, orientate the seal as
required, then mark the centers of its mounting holes.

Cutting the bracket

Wheel spindle
19 mm (3/4 in) diameter
25 mm (1 in) diameter
32 mm (11/4 in) diameter

1. With the wheel still in place, hold the bracket under the wheel
drive so you can mark dimension A – the distance between the
mounting surface and the rear edge of the wheel drive front cover.
Note: If the wheel is bent or not running true, dimension A will
change. Measure the shortest distance.

Alternative positions

2
15
mm

Cut here

154 mm (6.1 in)

in)

A + 10 mm

0
(6.

A

A

Motor tube seal
D5

603

-1

2. Use a hacksaw to cut the pin 10 mm (0.4 in) LONGER than
dimension A. Remove any sharp edges with a file or sandpaper.
3. Position the bracket so the pin is in the middle of the relevant slot.
Note: the center of the bracket pin should be 154 mm (6.1 in) from
the center of the wheel spindle.
4. Mark the center of the bracket's mounting holes then remove the
wheel and drive.

Attaching the bracket and ring/seal

1. Drill 4 mm (5/32 in) diameter pilot holes for the bracket and
ring/seal mounting screws.
2. Attach the bracket using three self tapping screws
(No 10 x 3/4 in). Note: on fiber-glass surfaces you may
need to replace the mounting screws with suitable
nuts, bolts and washers.
3. Remove the ring/seal from the motor tube, then use
three self tapping screws (No 10 x 3/4 in) to attach
them to the mounting surface.
Note: make sure the rubber seal is closest to the
surface (i.e. with the metal ring on top).
1. Attach the drive cable to the socket on the motor
tube, then secure the cable so it is clear of any
moving parts.
2. Fit the wheel and drive back onto the wheel spindle
and fully tighten the wheel nut.
3. Route the cable to the control unit, bearing in mind
the EMC guidelines in the ST4000+ Handbook.
Document number: 84092-1

Slot 1

Motor tube
48 mm (1.9 in) diameter

Bracket location

Motor tube hole
55 mm (21/8 in) diameter

min. clearance:
45 mm (1.8 in)

Final assembly

190 mm (7.5 in)
235 mm (9.3 in)



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 2001:07:05 13:48:57+01:00
Create Date                     : 2001:06:05 13:48:57
Producer                        : Adobe PDF Library 4.0
Creator                         : Adobe Illustrator 8.0
Title                           : D5603_1.eps
Page Count                      : 1

EXIF Metadata provided by EXIF.tools