Rayson Technology BTA-121 Bluetooth class2 Audio Transmitter User Manual BTA 131 2008 1 31

Download:
Mirror Download [FCC.gov]
Document ID	909391
Application ID	36Z+zPwkwc7wsEBiH1mmtw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.1kB (51302 bits)
Date Submitted	2008-03-04 00:00:00
Date Available	2008-03-04 00:00:00
Creation Date	2008-01-31 16:19:02
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-02-27 13:59:48
Document Title	Microsoft Word - BTA-131 user manual-2008.1.31
Document Creator	Acrobat PDFMaker 7.0.7 for Word
Document Author:	rayson

interference to radio communications.
BTA-121 Stereo Headset AdapteUser
Manual
However, there is no guarantee
that interference will not occur in a particular installation.
If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
Stereo Headset Adapter overv
on, the user is encouraged to try to correct the interference by one of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
1. LED indicator
2. Power On/Off
3. Pairing button
4. Audio connector
5. Mini USB charging port
6. Audio jack
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
Charging your Stereo Headset Adapter
Plug one end of the charger into your Stereo Headset Adapter and the
other end into an electrical outlet. The red LED indicator lights up when
charging and off when Stereo Headset Adapter fully charged.
The rechargeable batteries that power this product must be disposed of
properly and may need to be recycled. Contact your local
recycling center for proper disposal methods. Never dispose
received, including interference that may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. To maintain compliance with FCC
RF exposure compliance requirements, please avoid direct contact to
the transmitting antenna during transmitting.
of batteries in a fire because they may explode.
Turn on/off your Stereo Headset Adapter
To turn the Stereo Headset Adapter on, set the switch to On.
To turn the Stereo Headset Adapter off, set the switch to Off.
The LED indicator flashes blue when the Stereo Headset Adapter is
operating. When running out of battery, the LED indicator will flash red
slowly
Pairing and connecting
At the first time using the Stereo Headset Adapter, you must pair with
the other Bluetooth headset..
Please take the instructions step by step
1. Power on the both devices.
2. Make your Bluetooth headset into a pairing mode (refer to the user
guide enclosed with the product).
3. Place the Stereo Headset Adapter in pairing mode by pressing the
Pairing button lasting for 2 seconds. Release the button when the
LED indicator begins to flash quickly.
4. When the blue LED flashes slowly, the Stereo Headset Adapter is
successfully paired.
5. If pairing fails, please try again the above steps.
Note: In some circumstances the pairing process can take up to 2
minutes to complete.
6. The Stereo Headset Adapter will automatically initiate a paired
connection (when powered on) with the last paired headset. In
case the connection is undone, you can manually connect the
Stereo Headset Adapter to the headset by pressing the Pairing
button (less than 1 sec)
Using your Stereo Headset Adapter
The Stereo Headset Adapter is compatible with most popular
non-Bluetooth devices with a standard 2.5mm headset jack. You can
connect the Stereo Headset Adapter to the non-Bluetooth devices with
the attached audio connector.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
-1-
-2-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Source Modified                 : D:20080131081812
Create Date                     : 2008:01:31 16:19:02+08:00
Creator Tool                    : Acrobat PDFMaker 7.0.7 for Word
Modify Date                     : 2008:02:27 13:59:48+08:00
Metadata Date                   : 2008:02:27 13:59:48+08:00
Document ID                     : uuid:f8f2c590-9231-43a5-946e-84e17e530324
Instance ID                     : uuid:22815353-373f-4bb9-9a1b-66d1ea25dfaa
Version ID                      : 2
Format                          : application/pdf
Title                           : Microsoft Word - BTA-131 user manual-2008.1.31
Creator                         : rayson
Subject                         : 
Headline                        : 
Page Count                      : 1
Page Layout                     : OneColumn
Language                        : EN-US
Author                          : rayson

EXIF Metadata provided by EXIF.tools